From: Eric Nelson <eric.nelson@boundarydevices.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings
Date: Tue, 1 May 2012 12:55:11 -0700 [thread overview]
Message-ID: <1335902111-10159-1-git-send-email-eric.nelson@boundarydevices.com> (raw)
In-Reply-To: <http://lists.denx.de/pipermail/u-boot/2012-April/#123169>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
---
V2 has been stripped of the board-independent changes and
uses clrsetbits_le32() instead of twiddling bits by hand.
V3 returns immediately from setup_sata() if enable_sata_clock()
returns an error.
V4 removes extra #include and addresses a style issue as discussed
on the ML.
V5 addresses another (hopefully last) style issue.
board/freescale/mx6qsabrelite/mx6qsabrelite.c | 31 +++++++++++++++++++++++++
include/configs/mx6qsabrelite.h | 13 ++++++++++
2 files changed, 44 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 1d09a72..cdd2f15 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -25,6 +25,7 @@
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx6x_pins.h>
#include <asm/arch/iomux-v3.h>
+#include <asm/arch/clock.h>
#include <asm/errno.h>
#include <asm/gpio.h>
#include <mmc.h>
@@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis)
return 0;
}
+#ifdef CONFIG_CMD_SATA
+
+int setup_sata(void)
+{
+ struct iomuxc_base_regs *const iomuxc_regs
+ = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR;
+ int ret = enable_sata_clock();
+ if (ret)
+ return ret;
+
+ clrsetbits_le32(&iomuxc_regs->gpr[13],
+ IOMUXC_GPR13_SATA_MASK,
+ IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
+ |IOMUXC_GPR13_SATA_PHY_7_SATA2M
+ |IOMUXC_GPR13_SATA_SPEED_3G
+ |(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
+ |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
+ |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16
+ |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB
+ |IOMUXC_GPR13_SATA_PHY_2_TX_1P104V
+ |IOMUXC_GPR13_SATA_PHY_1_SLOW);
+
+ return 0;
+}
+#endif
+
int board_early_init_f(void)
{
setup_iomux_uart();
@@ -283,6 +310,10 @@ int board_init(void)
setup_spi();
#endif
+#ifdef CONFIG_CMD_SATA
+ setup_sata();
+#endif
+
return 0;
}
diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h
index f52c3c7..1d92dd0 100644
--- a/include/configs/mx6qsabrelite.h
+++ b/include/configs/mx6qsabrelite.h
@@ -71,6 +71,19 @@
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_SATA
+/*
+ * SATA Configs
+ */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_DWC_AHSATA_PORT_ID 0
+#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
--
1.7.9
next prev parent reply other threads:[~2012-05-01 19:55 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <http://lists.denx.de/pipermail/u-boot/2012-April/#123169>
2012-05-01 19:24 ` [U-Boot] [PATCH V4] i.MX6: mx6q_sabrelite: add SATA bindings Eric Nelson
2012-05-01 19:25 ` Marek Vasut
2012-05-01 19:53 ` Eric Nelson
2012-05-01 21:11 ` Marek Vasut
2012-05-01 21:58 ` Eric Nelson
2012-05-01 19:55 ` Eric Nelson [this message]
2012-05-01 20:09 ` [U-Boot] [PATCH V5] " Marek Vasut
2012-05-01 20:23 ` Eric Nelson
2012-05-06 17:06 ` Stefano Babic
2012-05-06 17:10 ` Stefano Babic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1335902111-10159-1-git-send-email-eric.nelson@boundarydevices.com \
--to=eric.nelson@boundarydevices.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox