[U-Boot] [PATCH 5/8] tegra: usb: move controller init into start_port

[Lucas Stach <dev@lynxeye.de>]

Am Dienstag, den 30.10.2012, 06:27 -0700 schrieb Simon Glass:
> Hi Lucas,
> 
> On Tue, Oct 30, 2012 at 2:22 AM, Lucas Stach <dev@lynxeye.de> wrote:
> > There is no need to init a USB controller before the upper layers indicate
> > that they are actually going to use it.
> >
> > board_usb_init now only parses the device tree and sets up the common pll.
> >
> > Signed-off-by: Lucas Stach <dev@lynxeye.de>
> > ---
> >  arch/arm/cpu/armv7/tegra20/usb.c | 47 +++++++++++++++-------------------------
> >  1 Datei ge?ndert, 18 Zeilen hinzugef?gt(+), 29 Zeilen entfernt(-)
> >
> > diff --git a/arch/arm/cpu/armv7/tegra20/usb.c b/arch/arm/cpu/armv7/tegra20/usb.c
> > index cf800b1..e372b8b 100644
> > --- a/arch/arm/cpu/armv7/tegra20/usb.c
> > +++ b/arch/arm/cpu/armv7/tegra20/usb.c
> > @@ -417,44 +417,29 @@ static int init_ulpi_usb_controller(struct fdt_usb *config)
> >  }
> >  #endif
> >
> > -/**
> > - * Add a new USB port to the list of available ports.
> > - *
> > - * @param config       USB port configuration
> > - * @return 0 if ok, -1 if error (too many ports)
> > - */
> > -static int add_port(struct fdt_usb *config)
> > +int tegrausb_start_port(int portnum, u32 *hccr, u32 *hcor)
> >  {
> > -       if (port_count == USB_PORTS_MAX) {
> > -               printf("tegrausb: Cannot register more than %d ports\n",
> > -                     USB_PORTS_MAX);
> > +       struct fdt_usb *config;
> > +       struct usb_ctlr *usbctlr;
> > +
> > +       if (portnum >= port_count)
> >                 return -1;
> > -       }
> > +
> > +       config = &port[portnum];
> >
> >         if (config->utmi && init_utmi_usb_controller(config)) {
> > -               printf("tegrausb: Cannot init port\n");
> > +               printf("tegrausb: Cannot init port %d\n", portnum);
> >                 return -1;
> >         }
> >
> >         if (config->ulpi && init_ulpi_usb_controller(config)) {
> > -               printf("tegrausb: Cannot init port\n");
> > +               printf("tegrausb: Cannot init port %d\n", portnum);
> >                 return -1;
> >         }
> >
> > -       port[port_count++] = *config;
> > -
> > -       return 0;
> > -}
> > +       set_host_mode(config);
> 
> This is good, but now I think you will re-init the USB peripheral at
> every 'usb start'. Perhaps you should remember whether it has been
> inited and only do it the first time?

I have to look this up, but the upper USB layers should not call those
lowlevel init functions repeatedly unless explicitly asked for it
through a "usb reset" or the like. If it actually does so it's a bug in
the upper layer and should not be fixed up in the lowlevel functions.

Regards,
Lucas