From: Lucas Stach <dev@lynxeye.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 04/11] tegra20: switch over tamonten platform to use tablebased pinmux
Date: Thu, 24 Jan 2013 17:48:13 +0100 [thread overview]
Message-ID: <1359046100-19385-5-git-send-email-dev@lynxeye.de> (raw)
In-Reply-To: <1359046100-19385-1-git-send-email-dev@lynxeye.de>
Init pinmux in one shot, in order to avoid any conflicts.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
---
board/avionic-design/common/tamonten.c | 133 ++++++++++++++++++++++++++++-----
include/configs/medcom-wide.h | 3 +
include/configs/plutux.h | 3 +
include/configs/tec.h | 3 +
4 files changed, 125 insertions(+), 17 deletions(-)
diff --git a/board/avionic-design/common/tamonten.c b/board/avionic-design/common/tamonten.c
index e6a932e..f072407 100644
--- a/board/avionic-design/common/tamonten.c
+++ b/board/avionic-design/common/tamonten.c
@@ -3,6 +3,8 @@
* NVIDIA Corporation <www.nvidia.com>
* (C) Copyright 2011-2012
* Avionic Design GmbH <www.avionic-design.de>
+ * (C) Copyright 2013
+ * Lucas Stach
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -28,7 +30,6 @@
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/clock.h>
-#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/tegra.h>
#include <asm/arch-tegra/board.h>
@@ -50,28 +51,126 @@ void gpio_early_init(void)
#endif
#ifdef CONFIG_TEGRA_MMC
-/*
- * Routine: pin_mux_mmc
- * Description: setup the pin muxes/tristate values for the SDMMC(s)
- */
-static void pin_mux_mmc(void)
-{
- funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
- /* for write-protect GPIO PI6 */
- pinmux_tristate_disable(PINGRP_ATA);
- /* for CD GPIO PH2 */
- pinmux_tristate_disable(PINGRP_ATD);
-}
-
/* this is a weak define that we are overriding */
int board_mmc_init(bd_t *bd)
{
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
/* init dev 0, SD slot, with 4-bit bus */
tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2);
return 0;
}
#endif
+
+static struct pingroup_config tamonten_pinmux[] = {
+ PINMUX_ENTRY(ATA, IDE, NORMAL, NORMAL), /* GPIO */
+ PINMUX_ENTRY(ATB, SDIO4, NORMAL, NORMAL), /* MMC */
+ PINMUX_ENTRY(ATC, NAND, NORMAL, TRISTATE),
+ PINMUX_ENTRY(ATD, GMI, NORMAL, NORMAL), /* GPIO */
+ PINMUX_ENTRY(ATE, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(CDEV1, PLLA_OUT, NORMAL, TRISTATE),
+ PINMUX_ENTRY(CDEV2, PLLP_OUT4, NORMAL, TRISTATE),
+ PINMUX_ENTRY(CRTP, CRT, NORMAL, TRISTATE),
+ PINMUX_ENTRY(CSUS, VI_SENSOR_CLK, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DAP1, DAP1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DAP2, DAP2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DAP3, DAP3, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DAP4, DAP4, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DDC, RSVD4, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DTA, SDIO2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DTB, RSVD1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DTC, RSVD1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DTD, SDIO2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DTE, RSVD1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(DTF, I2C3, NORMAL, TRISTATE),
+ PINMUX_ENTRY(GMA, SDIO4, NORMAL, NORMAL), /* MMC */
+ PINMUX_ENTRY(GMB, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(GMC, UARTD, NORMAL, NORMAL), /* UART D */
+ PINMUX_ENTRY(GMD, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(GME, SDIO4, NORMAL, NORMAL), /* MMC */
+ PINMUX_ENTRY(GPU, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(GPU7, RTCK, NORMAL, NORMAL), /* JTAG RTCK */
+ PINMUX_ENTRY(GPV, PCIE, NORMAL, TRISTATE),
+ PINMUX_ENTRY(HDINT, HDMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(I2CP, I2C, NORMAL, TRISTATE),
+ PINMUX_ENTRY(IRRX, UARTA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(IRTX, UARTA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(KBCA, KBC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(KBCB, KBC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(KBCC, KBC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(KBCD, KBC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(KBCE, KBC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(KBCF, KBC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LCSN, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD0, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD1, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD2, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD3, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD4, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD5, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD6, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD7, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD8, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD9, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD10, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD11, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD12, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD13, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD14, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD15, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD16, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LD17, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LDC, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LDI, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LHP0, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LHP1, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LHP2, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LHS, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LM0, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LM1, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LPP, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LPW0, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LPW1, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LPW2, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LSC0, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LSC1, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LSCK, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LSDA, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LSDI, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LSPI, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LVP0, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LVP1, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(LVS, DISPA, NORMAL, TRISTATE),
+ PINMUX_ENTRY(OWC, RSVD2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(PTA, RSVD4, NORMAL, TRISTATE),
+ PINMUX_ENTRY(RM, I2C, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SDB, PWM, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SDC, PWM, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SDD, PWM, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SDIO1, SDIO1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SLXA, PCIE, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SLXC, SPDIF, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SLXD, SPDIF, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SLXK, PCIE, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPDI, RSVD2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPDO, RSVD2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIA, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIB, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIC, GMI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPID, SPI1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIE, SPI1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIF, SPI1, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIG, SPI2_ALT, NORMAL, TRISTATE),
+ PINMUX_ENTRY(SPIH, SPI2_ALT, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UAA, ULPI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UAB, ULPI, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UAC, RSVD2, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UAD, UARTB, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UCA, UARTC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UCB, UARTC, NORMAL, TRISTATE),
+ PINMUX_ENTRY(UDA, ULPI, NORMAL, TRISTATE),
+};
+
+void pinmux_init(void)
+{
+ pinmux_config_table(tamonten_pinmux, ARRAY_SIZE(tamonten_pinmux));
+}
diff --git a/include/configs/medcom-wide.h b/include/configs/medcom-wide.h
index bae4ba0..a2913ee 100644
--- a/include/configs/medcom-wide.h
+++ b/include/configs/medcom-wide.h
@@ -28,6 +28,9 @@
#include "tegra20-common.h"
+/* Enable tablebased pinmux */
+#define CONFIG_TEGRA_TABLEBASED_PINMUX
+
/* Enable fdt support for Medcom-Wide. Flash the image in u-boot-dtb.bin */
#define CONFIG_DEFAULT_DEVICE_TREE tegra20-medcom-wide
#define CONFIG_OF_CONTROL
diff --git a/include/configs/plutux.h b/include/configs/plutux.h
index deee237..5a02c27 100644
--- a/include/configs/plutux.h
+++ b/include/configs/plutux.h
@@ -28,6 +28,9 @@
#include "tegra20-common.h"
+/* Enable tablebased pinmux */
+#define CONFIG_TEGRA_TABLEBASED_PINMUX
+
/* Enable fdt support for Plutux. Flash the image in u-boot-dtb.bin */
#define CONFIG_DEFAULT_DEVICE_TREE tegra20-plutux
#define CONFIG_OF_CONTROL
diff --git a/include/configs/tec.h b/include/configs/tec.h
index caeb9cd..74c56d8 100644
--- a/include/configs/tec.h
+++ b/include/configs/tec.h
@@ -28,6 +28,9 @@
#include "tegra20-common.h"
+/* Enable tablebased pinmux */
+#define CONFIG_TEGRA_TABLEBASED_PINMUX
+
/* Enable fdt support for TEC. Flash the image in u-boot-dtb.bin */
#define CONFIG_DEFAULT_DEVICE_TREE tegra20-tec
#define CONFIG_OF_CONTROL
--
1.8.0.2
next prev parent reply other threads:[~2013-01-24 16:48 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-01-24 16:48 [U-Boot] [PATCH 00/11] tablebased pinmux for Tegra20 Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 01/11] tegra: introduce config option to do table based pinmux Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 02/11] tegra20: add entry point and helper for tablebased pinmux Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 03/11] tegra20: switch over colibri_t20 board to use " Lucas Stach
2013-01-24 16:48 ` Lucas Stach [this message]
2013-01-25 22:04 ` [U-Boot] [PATCH 04/11] tegra20: switch over tamonten platform " Stephen Warren
2013-01-25 22:11 ` Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 05/11] tegra20: switch over harmony board " Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 06/11] tegra20: switch over seaboard and ventana " Lucas Stach
2013-01-24 17:54 ` Simon Glass
2013-01-24 18:22 ` Lucas Stach
2013-01-25 21:20 ` Simon Glass
2013-01-25 21:38 ` Lucas Stach
2013-01-25 21:49 ` Simon Glass
2013-01-25 21:57 ` Lucas Stach
2013-01-25 22:09 ` Stephen Warren
2013-01-25 22:10 ` Stephen Warren
2013-01-27 16:36 ` Simon Glass
2013-01-25 22:06 ` Stephen Warren
2013-01-24 16:48 ` [U-Boot] [PATCH 07/11] tegra20: switch over whistler board " Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 08/11] tegra20: switch over paz00 " Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 09/11] tegra20: switch over trimslice " Lucas Stach
2013-01-24 16:48 ` [U-Boot] [PATCH 10/11] tegra20: remove old pinmux setup Lucas Stach
2013-01-25 22:12 ` Stephen Warren
2013-01-25 22:19 ` Lucas Stach
2013-01-25 22:34 ` Stephen Warren
2013-01-24 16:48 ` [U-Boot] [PATCH 11/11] tegra20: remove funcmux Lucas Stach
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1359046100-19385-5-git-send-email-dev@lynxeye.de \
--to=dev@lynxeye.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox