[U-Boot] [PATCH v3 2/7] tegra: usb: make controller init functions more self contained

[Lucas Stach <dev@lynxeye.de>]

There is no need to pass around all those parameters. The init functions
are able to easily extract all the needed setup info on their own.

This allows to move out the controller init into ehci_hcd_init later
on, without having to save away global state for later use  and thus
bloating the file global state.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
---
 arch/arm/cpu/armv7/tegra20/usb.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/arch/arm/cpu/armv7/tegra20/usb.c b/arch/arm/cpu/armv7/tegra20/usb.c
index f151fb2..07c1ade 100644
--- a/arch/arm/cpu/armv7/tegra20/usb.c
+++ b/arch/arm/cpu/armv7/tegra20/usb.c
@@ -198,11 +198,12 @@ void usbf_reset_controller(struct fdt_usb *config, struct usb_ctlr *usbctlr)
 }
 
 /* set up the UTMI USB controller with the parameters provided */
-static int init_utmi_usb_controller(struct fdt_usb *config,
-				struct usb_ctlr *usbctlr, const u32 timing[])
+static int init_utmi_usb_controller(struct fdt_usb *config)
 {
 	u32 val;
 	int loop_count;
+	const unsigned *timing;
+	struct usb_ctlr *usbctlr = config->reg;
 
 	clock_enable(config->periph_id);
 
@@ -229,6 +230,8 @@ static int init_utmi_usb_controller(struct fdt_usb *config,
 	 * PLL Delay CONFIGURATION settings. The following parameters control
 	 * the bring up of the plls.
 	 */
+	timing = usb_pll[clock_get_osc_freq()];
+
 	val = readl(&usbctlr->utmip_misc_cfg1);
 	clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
 		timing[PARAM_STABLE_COUNT] << UTMIP_PLLU_STABLE_COUNT_SHIFT);
@@ -331,12 +334,12 @@ static int init_utmi_usb_controller(struct fdt_usb *config,
 #endif
 
 /* set up the ULPI USB controller with the parameters provided */
-static int init_ulpi_usb_controller(struct fdt_usb *config,
-				struct usb_ctlr *usbctlr)
+static int init_ulpi_usb_controller(struct fdt_usb *config)
 {
 	u32 val;
 	int loop_count;
 	struct ulpi_viewport ulpi_vp;
+	struct usb_ctlr *usbctlr = config->reg;
 
 	/* set up ULPI reference clock on pllp_out4 */
 	clock_enable(PERIPH_ID_DEV2_OUT);
@@ -408,8 +411,7 @@ static int init_ulpi_usb_controller(struct fdt_usb *config,
 	return 0;
 }
 #else
-static int init_ulpi_usb_controller(struct fdt_usb *config,
-				struct usb_ctlr *usbctlr)
+static int init_ulpi_usb_controller(struct fdt_usb *config)
 {
 	printf("No code to set up ULPI controller, please enable"
 			"CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT");
@@ -430,22 +432,20 @@ static void config_clock(const u32 timing[])
  * @param config	USB port configuration
  * @return 0 if ok, -1 if error (too many ports)
  */
-static int add_port(struct fdt_usb *config, const u32 timing[])
+static int add_port(struct fdt_usb *config)
 {
-	struct usb_ctlr *usbctlr = config->reg;
-
 	if (port_count == USB_PORTS_MAX) {
 		printf("tegrausb: Cannot register more than %d ports\n",
 		      USB_PORTS_MAX);
 		return -1;
 	}
 
-	if (config->utmi && init_utmi_usb_controller(config, usbctlr, timing)) {
+	if (config->utmi && init_utmi_usb_controller(config)) {
 		printf("tegrausb: Cannot init port\n");
 		return -1;
 	}
 
-	if (config->ulpi && init_ulpi_usb_controller(config, usbctlr)) {
+	if (config->ulpi && init_ulpi_usb_controller(config)) {
 		printf("tegrausb: Cannot init port\n");
 		return -1;
 	}
@@ -558,7 +558,7 @@ int board_usb_init(const void *blob)
 			return -1;
 		}
 
-		if (add_port(&config, usb_pll[freq]))
+		if (add_port(&config))
 			return -1;
 		set_host_mode(&config);
 	}
-- 
1.8.1