public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: York Sun <yorksun@freescale.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 14/31] powerpc/t4qds: use clock measurement for sysclk and ddr clock
Date: Fri, 22 Mar 2013 10:29:12 -0700	[thread overview]
Message-ID: <1363973369-26110-14-git-send-email-yorksun@freescale.com> (raw)
In-Reply-To: <1363973369-26110-1-git-send-email-yorksun@freescale.com>

From: Ed Swarthout <Ed.Swarthout@freescale.com>

Use QIXIS measurement registers to obtain sysclk and ddr clock. This
allows using non-standard clock speeds, set by directly writing to
clock chip or store the values in qixis clock data eeprom.

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
---
 board/freescale/t4qds/t4qds.c |   30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/board/freescale/t4qds/t4qds.c b/board/freescale/t4qds/t4qds.c
index 3eec601..5571a00 100644
--- a/board/freescale/t4qds/t4qds.c
+++ b/board/freescale/t4qds/t4qds.c
@@ -541,6 +541,21 @@ int board_early_init_r(void)
 unsigned long get_board_sys_clk(void)
 {
 	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+	/* use accurate clock measurement */
+	int freq = QIXIS_READ(clk_freq[0]) << 8 | QIXIS_READ(clk_freq[1]);
+	int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+	u32 val;
+
+	val =  freq * base;
+	if (val) {
+		debug("SYS Clock measurement is: %d\n", val);
+		return val;
+	} else {
+		printf("Warning: SYS clock measurement is invalid, "
+			"using value from brdcfg1.\n");
+	}
+#endif
 
 	switch (sysclk_conf & 0x0F) {
 	case QIXIS_SYSCLK_83:
@@ -564,6 +579,21 @@ unsigned long get_board_sys_clk(void)
 unsigned long get_board_ddr_clk(void)
 {
 	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+	/* use accurate clock measurement */
+	int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]);
+	int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+	u32 val;
+
+	val =  freq * base;
+	if (val) {
+		debug("DDR Clock measurement is: %d\n", val);
+		return val;
+	} else {
+		printf("Warning: DDR clock measurement is invalid, "
+			"using value from brdcfg1.\n");
+	}
+#endif
 
 	switch ((ddrclk_conf & 0x30) >> 4) {
 	case QIXIS_DDRCLK_100:
-- 
1.7.9.5

  parent reply	other threads:[~2013-03-22 17:29 UTC|newest]

Thread overview: 42+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-03-22 17:28 [U-Boot] [PATCH 01/31] 83xx/pcie: fix build error for 83xx pcie York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 02/31] Enable L2 cache parity/ECC error checking York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 03/31] net/phy: fix select line for TN80xx York Sun
2013-03-22 20:59   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 04/31] powerpc/mpc85xx: check if core is disabled for showing status York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 05/31] powerpc/t4240qds: Add VDD override York Sun
2013-03-22 21:00   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 06/31] T4240/ramboot: enable PBL tool for T4240 York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 07/31] Add e6500 L2 replacement policy selection York Sun
2013-03-22 21:00   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 08/31] powerpc/p5040: enable NAND, SD, SPI boot support York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 09/31] powerpc/T4160: Merge T4160 and T4240 in config_mpc85xx.h York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 10/31] powerpc/mpc8xxx: Add T1040 and variant SoCs York Sun
2013-03-22 21:00   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 11/31] powerpc/chassis2: Change core numbering scheme York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 12/31] powerpc/mpc8xxx: Allow DDR overclock York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 13/31] powerpc/qixis: add clock measurement registers York Sun
2013-03-22 17:29 ` York Sun [this message]
2013-03-22 21:01   ` [U-Boot] [PATCH 14/31] powerpc/t4qds: use clock measurement for sysclk and ddr clock Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 15/31] powerpc/p5040: enable PBL tool support York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 16/31] board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32M York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 17/31] Enable XAUI interface for B4860QDS York Sun
2013-03-22 21:02   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 18/31] powerpc/t4qds: Add SW7[4] in the DIP switch display York Sun
2013-03-22 21:02   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 19/31] powerpc/t4qds: Enable master module for Boot from SRIO and PCIE York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 20/31] powerpc/t4qds: Slave module for boot " York Sun
2013-03-22 21:02   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 21/31] powerpc/t4240qds: fix PHY reset timeout issue York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 22/31] powerpc/doc: Fix the misalignment of document README.srio-pcie-boot-corenet York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 23/31] powerpc/b4860: fix for Serdes connectivity to SFP's York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 24/31] powerpc/mpc85xx: add setting of clock-frequency for mpic node York Sun
2013-03-22 21:03   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 25/31] powerpc/p2041: fix serdes reference clock frequency display for PC board York Sun
2013-03-22 21:03   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 26/31] sf: spansion: Add support for S25FL128S York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 27/31] powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.h York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 28/31] powerpc/p5040: fix mdio mux for 10G port York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 29/31] powerpc/usb: Fix usb device-tree fix-up York Sun
2013-03-22 21:04   ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 30/31] fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speed York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 31/31] powerpc/b4860qds: Add LAW Target ID and Create LAW entry for Maple York Sun

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1363973369-26110-14-git-send-email-yorksun@freescale.com \
    --to=yorksun@freescale.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox