From: York Sun <yorksun@freescale.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 23/31] powerpc/b4860: fix for Serdes connectivity to SFP's
Date: Fri, 22 Mar 2013 10:29:21 -0700 [thread overview]
Message-ID: <1363973369-26110-23-git-send-email-yorksun@freescale.com> (raw)
In-Reply-To: <1363973369-26110-1-git-send-email-yorksun@freescale.com>
From: Shaveta Leekha <shaveta@freescale.com>
Crossbar switches were wrongly programmed to
route the CPRI lanes to SFP as the connectivity table
was not correct.
Modified it correctly for SFPs connections.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
---
board/freescale/b4860qds/b4860qds.c | 6 +++--
board/freescale/b4860qds/b4860qds_crossbar_con.h | 31 +++++++++++++++-------
2 files changed, 25 insertions(+), 12 deletions(-)
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c
index 41887c2..a39c17a 100644
--- a/board/freescale/b4860qds/b4860qds.c
+++ b/board/freescale/b4860qds/b4860qds.c
@@ -166,11 +166,13 @@ int configure_vsc3316_3308(void)
ret = select_i2c_ch_pca(I2C_CH_VSC3316);
if (!ret) {
ret = vsc3316_config(VSC3316_TX_ADDRESS,
- vsc16_tx_sgmii_lane_ab, num_vsc16_con);
+ vsc16_tx_4sfp_sgmii_12_56,
+ num_vsc16_con);
if (ret)
return ret;
ret = vsc3316_config(VSC3316_RX_ADDRESS,
- vsc16_rx_sgmii_lane_ab, num_vsc16_con);
+ vsc16_rx_4sfp_sgmii_12_56,
+ num_vsc16_con);
if (ret)
return ret;
} else {
diff --git a/board/freescale/b4860qds/b4860qds_crossbar_con.h b/board/freescale/b4860qds/b4860qds_crossbar_con.h
index 994dec5..c2b6c44 100644
--- a/board/freescale/b4860qds/b4860qds_crossbar_con.h
+++ b/board/freescale/b4860qds/b4860qds_crossbar_con.h
@@ -26,42 +26,53 @@
static const int8_t vsc16_tx_amc[8][2] = { {15, 3}, {0, 2}, {7, 4}, {9, 10},
{5, 11}, {4, 5}, {2, 6}, {12, 9} };
-static const int8_t vsc16_tx_sfp[8][2] = { {15, 8}, {0, 0}, {7, 7}, {9, 1},
- {5, 15}, {4, 14}, {2, 12}, {12, 13} };
+static const int8_t vsc16_tx_sfp[8][2] = { {15, 7}, {0, 1}, {7, 8}, {9, 0},
+ {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
-static const int8_t vsc16_tx_sgmii_lane_ab[8][2] = { {2, 14}, {12, 15},
- {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+static const int8_t vsc16_tx_4sfp_sgmii_12_56[8][2] = { {15, 7}, {0, 1},
+ {7, 8}, {9, 0}, {2, 14}, {12, 15},
+ {-1, -1}, {-1, -1} };
+
+static const int8_t vsc16_tx_4sfp_sgmii_34[8][2] = { {15, 7}, {0, 1},
+ {7, 8}, {9, 0}, {5, 14}, {4, 15},
+ {-1, -1}, {-1, -1} };
#ifdef CONFIG_PPC_B4420
static const int8_t vsc16_tx_sgmii_lane_cd[8][2] = { {5, 14}, {4, 15},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
#endif
+
static const int8_t vsc16_tx_aurora[8][2] = { {2, 13}, {12, 12}, {-1, -1},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
static const int8_t vsc16_rx_amc[8][2] = { {3, 15}, {2, 1}, {4, 8}, {10, 9},
{11, 11}, {5, 10}, {6, 3}, {9, 12} };
-static const int8_t vsc16_rx_sfp[8][2] = { {0, 15}, {8, 1}, {1, 8}, {7, 9},
+static const int8_t vsc16_rx_sfp[8][2] = { {8, 15}, {0, 1}, {7, 8}, {1, 9},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
-static const int8_t vsc16_rx_sgmii_lane_ab[8][2] = { {14, 3}, {15, 12},
- {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+static const int8_t vsc16_rx_4sfp_sgmii_12_56[8][2] = { {8, 15}, {0, 1},
+ {7, 8}, {1, 9}, {14, 3}, {15, 12},
+ {-1, -1}, {-1, -1} };
+
+static const int8_t vsc16_rx_4sfp_sgmii_34[8][2] = { {8, 15}, {0, 1},
+ {7, 8}, {1, 9}, {14, 11}, {15, 10},
+ {-1, -1}, {-1, -1} };
#ifdef CONFIG_PPC_B4420
static const int8_t vsc16_rx_sgmii_lane_cd[8][2] = { {14, 11}, {15, 10},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
#endif
-static const int8_t vsc16_rx_aurora[8][2] = { {12, 3}, {13, 12}, {-1, -1},
+static const int8_t vsc16_rx_aurora[8][2] = { {13, 3}, {12, 12}, {-1, -1},
{-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
static const int8_t vsc08_tx_amc[4][2] = { {2, 2}, {3, 3}, {7, 4}, {1, 5} };
-static const int8_t vsc08_tx_sfp[4][2] = { {2, 6}, {3, 7}, {7, 1}, {1, 0} };
+static const int8_t vsc08_tx_sfp[4][2] = { {2, 1}, {3, 0}, {7, 6}, {1, 7} };
static const int8_t vsc08_rx_amc[4][2] = { {2, 3}, {3, 4}, {4, 7}, {5, 1} };
-static const int8_t vsc08_rx_sfp[4][2] = { {6, 3}, {7, 4}, {1, 7}, {0, 1} };
+static const int8_t vsc08_rx_sfp[4][2] = { {1, 3}, {0, 4}, {6, 7}, {7, 1} };
#endif
--
1.7.9.5
next prev parent reply other threads:[~2013-03-22 17:29 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-22 17:28 [U-Boot] [PATCH 01/31] 83xx/pcie: fix build error for 83xx pcie York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 02/31] Enable L2 cache parity/ECC error checking York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 03/31] net/phy: fix select line for TN80xx York Sun
2013-03-22 20:59 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 04/31] powerpc/mpc85xx: check if core is disabled for showing status York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 05/31] powerpc/t4240qds: Add VDD override York Sun
2013-03-22 21:00 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 06/31] T4240/ramboot: enable PBL tool for T4240 York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 07/31] Add e6500 L2 replacement policy selection York Sun
2013-03-22 21:00 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 08/31] powerpc/p5040: enable NAND, SD, SPI boot support York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 09/31] powerpc/T4160: Merge T4160 and T4240 in config_mpc85xx.h York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 10/31] powerpc/mpc8xxx: Add T1040 and variant SoCs York Sun
2013-03-22 21:00 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 11/31] powerpc/chassis2: Change core numbering scheme York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 12/31] powerpc/mpc8xxx: Allow DDR overclock York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 13/31] powerpc/qixis: add clock measurement registers York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 14/31] powerpc/t4qds: use clock measurement for sysclk and ddr clock York Sun
2013-03-22 21:01 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 15/31] powerpc/p5040: enable PBL tool support York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 16/31] board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32M York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 17/31] Enable XAUI interface for B4860QDS York Sun
2013-03-22 21:02 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 18/31] powerpc/t4qds: Add SW7[4] in the DIP switch display York Sun
2013-03-22 21:02 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 19/31] powerpc/t4qds: Enable master module for Boot from SRIO and PCIE York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 20/31] powerpc/t4qds: Slave module for boot " York Sun
2013-03-22 21:02 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 21/31] powerpc/t4240qds: fix PHY reset timeout issue York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 22/31] powerpc/doc: Fix the misalignment of document README.srio-pcie-boot-corenet York Sun
2013-03-22 17:29 ` York Sun [this message]
2013-03-22 17:29 ` [U-Boot] [PATCH 24/31] powerpc/mpc85xx: add setting of clock-frequency for mpic node York Sun
2013-03-22 21:03 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 25/31] powerpc/p2041: fix serdes reference clock frequency display for PC board York Sun
2013-03-22 21:03 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 26/31] sf: spansion: Add support for S25FL128S York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 27/31] powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.h York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 28/31] powerpc/p5040: fix mdio mux for 10G port York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 29/31] powerpc/usb: Fix usb device-tree fix-up York Sun
2013-03-22 21:04 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 30/31] fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speed York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 31/31] powerpc/b4860qds: Add LAW Target ID and Create LAW entry for Maple York Sun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1363973369-26110-23-git-send-email-yorksun@freescale.com \
--to=yorksun@freescale.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox