From: York Sun <yorksun@freescale.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 31/31] powerpc/b4860qds: Add LAW Target ID and Create LAW entry for Maple
Date: Fri, 22 Mar 2013 10:29:29 -0700 [thread overview]
Message-ID: <1363973369-26110-31-git-send-email-yorksun@freescale.com> (raw)
In-Reply-To: <1363973369-26110-1-git-send-email-yorksun@freescale.com>
From: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
---
arch/powerpc/include/asm/fsl_law.h | 2 ++
board/freescale/b4860qds/law.c | 3 +++
include/configs/B4860QDS.h | 9 +++++++++
3 files changed, 14 insertions(+)
diff --git a/arch/powerpc/include/asm/fsl_law.h b/arch/powerpc/include/asm/fsl_law.h
index f9cec8e..90b264d 100644
--- a/arch/powerpc/include/asm/fsl_law.h
+++ b/arch/powerpc/include/asm/fsl_law.h
@@ -70,6 +70,8 @@ enum law_trgt_if {
LAW_TRGT_IF_DCSR = 0x1d,
LAW_TRGT_IF_LBC = 0x1f,
LAW_TRGT_IF_QMAN = 0x3c,
+
+ LAW_TRGT_IF_MAPLE = 0x50,
};
#define LAW_TRGT_IF_DDR LAW_TRGT_IF_DDR_1
#define LAW_TRGT_IF_IFC LAW_TRGT_IF_LBC
diff --git a/board/freescale/b4860qds/law.c b/board/freescale/b4860qds/law.c
index abaad7a..b26725b 100644
--- a/board/freescale/b4860qds/law.c
+++ b/board/freescale/b4860qds/law.c
@@ -33,6 +33,9 @@ struct law_entry law_table[] = {
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
#endif
SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_MAPLE_MEM_PHYS
+ SET_LAW(CONFIG_SYS_MAPLE_MEM_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_MAPLE),
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
/* Limit DCSR to 32M to access NPC Trace Buffer */
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
index e871a70..c745fac 100644
--- a/include/configs/B4860QDS.h
+++ b/include/configs/B4860QDS.h
@@ -540,6 +540,15 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SF_DEFAULT_MODE 0
/*
+ * MAPLE
+ */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_MAPLE_MEM_PHYS 0xFA0000000ull
+#else
+#define CONFIG_SYS_MAPLE_MEM_PHYS 0xA0000000
+#endif
+
+/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
--
1.7.9.5
prev parent reply other threads:[~2013-03-22 17:29 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-22 17:28 [U-Boot] [PATCH 01/31] 83xx/pcie: fix build error for 83xx pcie York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 02/31] Enable L2 cache parity/ECC error checking York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 03/31] net/phy: fix select line for TN80xx York Sun
2013-03-22 20:59 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 04/31] powerpc/mpc85xx: check if core is disabled for showing status York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 05/31] powerpc/t4240qds: Add VDD override York Sun
2013-03-22 21:00 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 06/31] T4240/ramboot: enable PBL tool for T4240 York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 07/31] Add e6500 L2 replacement policy selection York Sun
2013-03-22 21:00 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 08/31] powerpc/p5040: enable NAND, SD, SPI boot support York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 09/31] powerpc/T4160: Merge T4160 and T4240 in config_mpc85xx.h York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 10/31] powerpc/mpc8xxx: Add T1040 and variant SoCs York Sun
2013-03-22 21:00 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 11/31] powerpc/chassis2: Change core numbering scheme York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 12/31] powerpc/mpc8xxx: Allow DDR overclock York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 13/31] powerpc/qixis: add clock measurement registers York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 14/31] powerpc/t4qds: use clock measurement for sysclk and ddr clock York Sun
2013-03-22 21:01 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 15/31] powerpc/p5040: enable PBL tool support York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 16/31] board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32M York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 17/31] Enable XAUI interface for B4860QDS York Sun
2013-03-22 21:02 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 18/31] powerpc/t4qds: Add SW7[4] in the DIP switch display York Sun
2013-03-22 21:02 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 19/31] powerpc/t4qds: Enable master module for Boot from SRIO and PCIE York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 20/31] powerpc/t4qds: Slave module for boot " York Sun
2013-03-22 21:02 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 21/31] powerpc/t4240qds: fix PHY reset timeout issue York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 22/31] powerpc/doc: Fix the misalignment of document README.srio-pcie-boot-corenet York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 23/31] powerpc/b4860: fix for Serdes connectivity to SFP's York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 24/31] powerpc/mpc85xx: add setting of clock-frequency for mpic node York Sun
2013-03-22 21:03 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 25/31] powerpc/p2041: fix serdes reference clock frequency display for PC board York Sun
2013-03-22 21:03 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 26/31] sf: spansion: Add support for S25FL128S York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 27/31] powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.h York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 28/31] powerpc/p5040: fix mdio mux for 10G port York Sun
2013-03-22 17:29 ` [U-Boot] [PATCH 29/31] powerpc/usb: Fix usb device-tree fix-up York Sun
2013-03-22 21:04 ` Wolfgang Denk
2013-03-22 17:29 ` [U-Boot] [PATCH 30/31] fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speed York Sun
2013-03-22 17:29 ` York Sun [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1363973369-26110-31-git-send-email-yorksun@freescale.com \
--to=yorksun@freescale.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox