From: Nishanth Menon <nm@ti.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH V2 3/9] twl6030: twl6030_i2c_[read|write]_u8 prototype consistent
Date: Fri, 22 Mar 2013 16:33:18 -0500 [thread overview]
Message-ID: <1363988004-25819-4-git-send-email-nm@ti.com> (raw)
In-Reply-To: <1363988004-25819-1-git-send-email-nm@ti.com>
u-boot standard i2c register access prototype is
i2c_read(addr, reg, 1, &buf, 1)
i2c_reg_write(u8 addr, u8 reg, u8 val)
twl6030_i2c_read_u8(u8 addr, u8 *val, u8 reg)
twl6030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl6030_i2c_read_u8(u8 addr, u8 reg, u8 *val)
twl6030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Signed-off-by: Nishanth Menon <nm@ti.com>
---
drivers/power/twl6030.c | 68 +++++++++++++++++++++++------------------------
1 file changed, 34 insertions(+), 34 deletions(-)
diff --git a/drivers/power/twl6030.c b/drivers/power/twl6030.c
index c5a0038..af1114c 100644
--- a/drivers/power/twl6030.c
+++ b/drivers/power/twl6030.c
@@ -26,12 +26,12 @@
#include <twl6030.h>
/* Functions to read and write from TWL6030 */
-static inline int twl6030_i2c_write_u8(u8 chip_no, u8 val, u8 reg)
+static inline int twl6030_i2c_write_u8(u8 chip_no, u8 reg, u8 val)
{
return i2c_write(chip_no, reg, 1, &val, 1);
}
-static inline int twl6030_i2c_read_u8(u8 chip_no, u8 *val, u8 reg)
+static inline int twl6030_i2c_read_u8(u8 chip_no, u8 reg, u8 *val)
{
return i2c_read(chip_no, reg, 1, val, 1);
}
@@ -42,13 +42,13 @@ static int twl6030_gpadc_read_channel(u8 channel_no)
u8 msb = 0;
int ret = 0;
- ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, &lsb,
- GPCH0_LSB + channel_no * 2);
+ ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC,
+ GPCH0_LSB + channel_no * 2, &lsb);
if (ret)
return ret;
- ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, &msb,
- GPCH0_MSB + channel_no * 2);
+ ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC,
+ GPCH0_MSB + channel_no * 2, &msb);
if (ret)
return ret;
@@ -60,7 +60,7 @@ static int twl6030_gpadc_sw2_trigger(void)
u8 val;
int ret = 0;
- ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, CTRL_P2_SP2, CTRL_P2);
+ ret = twl6030_i2c_write_u8(TWL6030_CHIP_ADC, CTRL_P2, CTRL_P2_SP2);
if (ret)
return ret;
@@ -68,7 +68,7 @@ static int twl6030_gpadc_sw2_trigger(void)
val = CTRL_P2_BUSY;
while (!((val & CTRL_P2_EOCP2) && (!(val & CTRL_P2_BUSY)))) {
- ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, &val, CTRL_P2);
+ ret = twl6030_i2c_read_u8(TWL6030_CHIP_ADC, CTRL_P2, &val);
if (ret)
return ret;
udelay(1000);
@@ -79,29 +79,29 @@ static int twl6030_gpadc_sw2_trigger(void)
void twl6030_stop_usb_charging(void)
{
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, 0, CONTROLLER_CTRL1);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CONTROLLER_CTRL1, 0);
return;
}
void twl6030_start_usb_charging(void)
{
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_VICHRG_1500,
- CHARGERUSB_VICHRG);
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_CIN_LIMIT_NONE,
- CHARGERUSB_CINLIMIT);
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, MBAT_TEMP,
- CONTROLLER_INT_MASK);
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, MASK_MCHARGERUSB_THMREG,
- CHARGERUSB_INT_MASK);
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_VOREG_4P0,
- CHARGERUSB_VOREG);
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_CTRL2_VITERM_400,
- CHARGERUSB_CTRL2);
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, TERM, CHARGERUSB_CTRL1);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CHARGERUSB_VICHRG, CHARGERUSB_VICHRG_1500);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CHARGERUSB_CINLIMIT, CHARGERUSB_CIN_LIMIT_NONE);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CONTROLLER_INT_MASK, MBAT_TEMP);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CHARGERUSB_INT_MASK, MASK_MCHARGERUSB_THMREG);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CHARGERUSB_VOREG, CHARGERUSB_VOREG_4P0);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CHARGERUSB_CTRL2, CHARGERUSB_CTRL2_VITERM_400);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CHARGERUSB_CTRL1, TERM);
/* Enable USB charging */
- twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, CONTROLLER_CTRL1_EN_CHARGER,
- CONTROLLER_CTRL1);
+ twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER,
+ CONTROLLER_CTRL1, CONTROLLER_CTRL1_EN_CHARGER);
return;
}
@@ -111,8 +111,8 @@ int twl6030_get_battery_current(void)
u8 msb = 0;
u8 lsb = 0;
- twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, &msb, FG_REG_11);
- twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, &lsb, FG_REG_10);
+ twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, FG_REG_11, &msb);
+ twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, FG_REG_10, &lsb);
battery_current = ((msb << 8) | lsb);
/* convert 10 bit signed number to 16 bit signed number */
@@ -156,10 +156,10 @@ void twl6030_init_battery_charging(void)
int ret = 0;
/* Enable VBAT measurement */
- twl6030_i2c_write_u8(TWL6030_CHIP_PM, VBAT_MEAS, MISC1);
+ twl6030_i2c_write_u8(TWL6030_CHIP_PM, MISC1, VBAT_MEAS);
/* Enable GPADC module */
- ret = twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, FGS | GPADCS, TOGGLE1);
+ ret = twl6030_i2c_write_u8(TWL6030_CHIP_CHARGER, TOGGLE1, FGS | GPADCS);
if (ret) {
printf("Failed to enable GPADC\n");
return;
@@ -173,7 +173,7 @@ void twl6030_init_battery_charging(void)
printf("Main battery voltage too low!\n");
/* Check for the presence of USB charger */
- twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, &stat1, CONTROLLER_STAT1);
+ twl6030_i2c_read_u8(TWL6030_CHIP_CHARGER, CONTROLLER_STAT1, &stat1);
/* check for battery presence indirectly via Fuel gauge */
if ((stat1 & VBUS_DET) && (battery_volt < 3300))
@@ -185,8 +185,8 @@ void twl6030_init_battery_charging(void)
void twl6030_power_mmc_init()
{
/* set voltage to 3.0 and turnon for APP */
- twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x15, VMMC_CFG_VOLTATE);
- twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x21, VMMC_CFG_STATE);
+ twl6030_i2c_write_u8(TWL6030_CHIP_PM, VMMC_CFG_VOLTATE, 0x15);
+ twl6030_i2c_write_u8(TWL6030_CHIP_PM, VMMC_CFG_STATE, 0x21);
}
void twl6030_usb_device_settings()
@@ -194,12 +194,12 @@ void twl6030_usb_device_settings()
u8 data = 0;
/* Select APP Group and set state to ON */
- twl6030_i2c_write_u8(TWL6030_CHIP_PM, 0x21, VUSB_CFG_STATE);
+ twl6030_i2c_write_u8(TWL6030_CHIP_PM, VUSB_CFG_STATE, 0x21);
- twl6030_i2c_read_u8(TWL6030_CHIP_PM, &data, MISC2);
+ twl6030_i2c_read_u8(TWL6030_CHIP_PM, MISC2, &data);
data |= 0x10;
/* Select the input supply for VBUS regulator */
- twl6030_i2c_write_u8(TWL6030_CHIP_PM, data, MISC2);
+ twl6030_i2c_write_u8(TWL6030_CHIP_PM, MISC2, data);
}
#endif
--
1.7.9.5
next prev parent reply other threads:[~2013-03-22 21:33 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-22 21:33 [U-Boot] [PATCH V2 0/9] OMAP3-5: TWL[46]03[05]: cleanup register access and misc minimal cleanups Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 1/9] twl4030: make twl4030_i2c_write_u8 prototype consistent Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 2/9] twl4030: make twl4030_i2c_read_u8 " Nishanth Menon
2013-03-22 21:33 ` Nishanth Menon [this message]
2013-03-22 21:33 ` [U-Boot] [PATCH V2 4/9] twl6030: move twl6030 register access functions to common header file Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 5/9] twl6030: add header guard Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 6/9] twl6035: make twl6030_i2c_[read|write]_u8 static inline Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 7/9] twl6035: twl6035_i2c_[read|write]_u8 prototype consistent Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 8/9] twl6035: remove redundant palmas_[read|write]_u8 Nishanth Menon
2013-03-22 21:33 ` [U-Boot] [PATCH V2 9/9] twl6035: add header guard Nishanth Menon
2013-03-25 17:47 ` [U-Boot] [PATCH V2 0/9] OMAP3-5: TWL[46]03[05]: cleanup register access and misc minimal cleanups Sricharan R
2013-03-25 18:20 ` Nishanth Menon
2013-03-26 9:31 ` Sricharan R
2013-03-26 13:25 ` Nishanth Menon
2013-03-26 13:34 ` Sricharan R
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1363988004-25819-4-git-send-email-nm@ti.com \
--to=nm@ti.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox