* [U-Boot] [PATCH 06/11] powerpc/T4240EMU: Add T4240EMU target
2013-06-25 18:37 [U-Boot] [PATCH 01/11] powerpc/corenet: Move CONFIG_FSL_CORENET out of board header file York Sun
` (3 preceding siblings ...)
2013-06-25 18:37 ` [U-Boot] [PATCH 05/11] powerpc/corenet: Move RCW print to cpu.c York Sun
@ 2013-06-25 18:37 ` York Sun
2013-06-25 21:24 ` Wolfgang Denk
2013-06-25 18:37 ` [U-Boot] [PATCH 07/11] powerpc/mpc8xxx: Set inactive csn_bnds to 0xffffffff York Sun
` (4 subsequent siblings)
9 siblings, 1 reply; 14+ messages in thread
From: York Sun @ 2013-06-25 18:37 UTC (permalink / raw)
To: u-boot
Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
ECC for DDR is disabled due the procedure to load images
No board FPGA (QIXIS)
NOR flash has 32-bit port for higher loading speed
IFC and I2C timing don't really matter, so set them fast
No ethernet
Signed-off-by: York Sun <yorksun@freescale.com>
---
board/freescale/t4qds/Makefile | 3 +-
board/freescale/t4qds/ddr.c | 73 +---
board/freescale/t4qds/ddr.h | 122 ++++++
board/freescale/t4qds/law.c | 2 +
board/freescale/t4qds/t4240emu.c | 96 +++++
board/freescale/t4qds/t4240qds.c | 855 ++++++++++++++++++++++++++++++++++++++
board/freescale/t4qds/t4qds.c | 853 -------------------------------------
board/freescale/t4qds/tlb.c | 3 +-
boards.cfg | 1 +
include/configs/T4240EMU.h | 185 +++++++++
include/configs/T4240QDS.h | 539 ++++++++++++++++++++++++
include/configs/t4qds.h | 482 +--------------------
12 files changed, 1807 insertions(+), 1407 deletions(-)
create mode 100644 board/freescale/t4qds/ddr.h
create mode 100644 board/freescale/t4qds/t4240emu.c
create mode 100644 board/freescale/t4qds/t4240qds.c
delete mode 100644 board/freescale/t4qds/t4qds.c
create mode 100644 include/configs/T4240EMU.h
diff --git a/board/freescale/t4qds/Makefile b/board/freescale/t4qds/Makefile
index ff09ffa..1923a47 100644
--- a/board/freescale/t4qds/Makefile
+++ b/board/freescale/t4qds/Makefile
@@ -24,7 +24,8 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
-COBJS-y += $(BOARD).o
+COBJS-$(CONFIG_T4240QDS) += t4240qds.o
+COBJS-$(CONFIG_T4240EMU) += t4240emu.o
COBJS-y += ddr.o
COBJS-$(CONFIG_T4240QDS)+= eth.o
COBJS-$(CONFIG_PCI) += pci.o
diff --git a/board/freescale/t4qds/ddr.c b/board/freescale/t4qds/ddr.c
index 058d625..26ac2a5 100644
--- a/board/freescale/t4qds/ddr.c
+++ b/board/freescale/t4qds/ddr.c
@@ -13,81 +13,10 @@
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
+#include "ddr.h"
DECLARE_GLOBAL_DATA_PTR;
-struct board_specific_parameters {
- u32 n_ranks;
- u32 datarate_mhz_high;
- u32 rank_gb;
- u32 clk_adjust;
- u32 wrlvl_start;
- u32 wrlvl_ctl_2;
- u32 wrlvl_ctl_3;
- u32 cpo;
- u32 write_data_delay;
- u32 force_2T;
-};
-
-/*
- * This table contains all valid speeds we want to override with board
- * specific parameters. datarate_mhz_high values need to be in ascending order
- * for each n_ranks group.
- */
-static const struct board_specific_parameters udimm0[] = {
- /*
- * memory controller 0
- * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
- * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
- */
- {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
- {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0},
- {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0},
- {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0},
- {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
- {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
- {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
- {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
- {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0},
- {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0},
- {}
-};
-
-/*
- * The three slots have slightly different timing. The center values are good
- * for all slots. We use identical speed tables for them. In future use, if
- * DIMMs require separated tables, make more entries as needed.
- */
-static const struct board_specific_parameters *udimms[] = {
- udimm0,
-};
-
-static const struct board_specific_parameters rdimm0[] = {
- /*
- * memory controller 0
- * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
- * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
- */
- {4, 1350, 0, 5, 9, 0x08070605, 0x07080805, 0xff, 2, 0},
- {4, 1666, 0, 5, 8, 0x08070605, 0x07080805, 0xff, 2, 0},
- {4, 2140, 0, 5, 8, 0x08070605, 0x07081805, 0xff, 2, 0},
- {2, 1350, 0, 5, 7, 0x0809090b, 0x0c0c0d09, 0xff, 2, 0},
- {2, 1666, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
- {2, 2140, 0, 5, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0},
- {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
- {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
- {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0},
- {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0},
- {}
-};
-
-/*
- * The three slots have slightly different timing. See comments above.
- */
-static const struct board_specific_parameters *rdimms[] = {
- rdimm0,
-};
-
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
diff --git a/board/freescale/t4qds/ddr.h b/board/freescale/t4qds/ddr.h
new file mode 100644
index 0000000..cde0785
--- /dev/null
+++ b/board/freescale/t4qds/ddr.h
@@ -0,0 +1,122 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+#ifdef CONFIG_T4240QDS
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0},
+ {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0},
+ {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0},
+ {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
+ {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
+ {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
+ {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0},
+ {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0},
+ {}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {4, 1350, 0, 5, 9, 0x08070605, 0x07080805, 0xff, 2, 0},
+ {4, 1666, 0, 5, 8, 0x08070605, 0x07080805, 0xff, 2, 0},
+ {4, 2140, 0, 5, 8, 0x08070605, 0x07081805, 0xff, 2, 0},
+ {2, 1350, 0, 5, 7, 0x0809090b, 0x0c0c0d09, 0xff, 2, 0},
+ {2, 1666, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
+ {2, 2140, 0, 5, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0},
+ {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
+ {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0},
+ {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0},
+ {}
+};
+
+#else /* CONFIG_T4240EMU */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {2, 2140, 0, 4, 8, 0x0, 0x0, 0xff, 2, 0},
+ {1, 2140, 0, 4, 8, 0x0, 0x0, 0xff, 2, 0},
+ {}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {4, 2140, 0, 5, 8, 0x0, 0x0, 0xff, 2, 0},
+ {2, 2140, 0, 5, 8, 0x0, 0x0, 0xff, 2, 0},
+ {1, 2140, 0, 4, 8, 0x0, 0x0, 0xff, 2, 0},
+ {}
+};
+#endif /* CONFIG_T4240EMU */
+
+/*
+ * The three slots have slightly different timing. The center values are good
+ * for all slots. We use identical speed tables for them. In future use, if
+ * DIMMs require separated tables, make more entries as needed.
+ */
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+/*
+ * The three slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+};
+
+
+#endif
diff --git a/board/freescale/t4qds/law.c b/board/freescale/t4qds/law.c
index f3848f3..7e41556 100644
--- a/board/freescale/t4qds/law.c
+++ b/board/freescale/t4qds/law.c
@@ -35,7 +35,9 @@ struct law_entry law_table[] = {
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
#endif
+#ifdef QIXIS_BASE_PHYS
SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
/* Limit DCSR to 32M to access NPC Trace Buffer */
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
diff --git a/board/freescale/t4qds/t4240emu.c b/board/freescale/t4qds/t4240emu.c
new file mode 100644
index 0000000..589a2ae
--- /dev/null
+++ b/board/freescale/t4qds/t4240emu.c
@@ -0,0 +1,96 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ struct cpu_type *cpu = gd->arch.cpu;
+
+ printf("Board: %sEMU\n", cpu->name);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+}
diff --git a/board/freescale/t4qds/t4240qds.c b/board/freescale/t4qds/t4240qds.c
new file mode 100644
index 0000000..9a714de
--- /dev/null
+++ b/board/freescale/t4qds/t4240qds.c
@@ -0,0 +1,855 @@
+/*
+ * Copyright 2009-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/qixis.h"
+#include "../common/vsc3316_3308.h"
+#include "t4qds.h"
+#include "t4240qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const int8_t vsc3316_fsm1_tx[8][2] = { {0, 0}, {1, 1}, {6, 6}, {7, 7},
+ {8, 8}, {9, 9}, {14, 14}, {15, 15} };
+
+static const int8_t vsc3316_fsm2_tx[8][2] = { {2, 2}, {3, 3}, {4, 4}, {5, 5},
+ {10, 10}, {11, 11}, {12, 12}, {13, 13} };
+
+static const int8_t vsc3316_fsm1_rx[8][2] = { {2, 12}, {3, 13}, {4, 5}, {5, 4},
+ {10, 11}, {11, 10}, {12, 2}, {13, 3} };
+
+static const int8_t vsc3316_fsm2_rx[8][2] = { {0, 15}, {1, 14}, {6, 7}, {7, 6},
+ {8, 9}, {9, 8}, {14, 1}, {15, 0} };
+
+int checkboard(void)
+{
+ char buf[64];
+ u8 sw;
+ struct cpu_type *cpu = gd->arch.cpu;
+ unsigned int i;
+
+ printf("Board: %sQDS, ", cpu->name);
+ printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ",
+ QIXIS_READ(id), QIXIS_READ(arch));
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ if (sw < 0x8)
+ printf("vBank: %d\n", sw);
+ else if (sw == 0x8)
+ puts("Promjet\n");
+ else if (sw == 0x9)
+ puts("NAND\n");
+ else
+ printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+
+ printf("FPGA: v%d (%s), build %d",
+ (int)QIXIS_READ(scver), qixis_read_tag(buf),
+ (int)qixis_read_minor());
+ /* the timestamp string contains "\n"@the end */
+ printf(" on %s", qixis_read_time(buf));
+
+ /*
+ * Display the actual SERDES reference clocks as configured by the
+ * dip switches on the board. Note that the SWx registers could
+ * technically be set to force the reference clocks to match the
+ * values that the SERDES expects (or vice versa). For now, however,
+ * we just display both values and hope the user notices when they
+ * don't match.
+ */
+ puts("SERDES Reference Clocks: ");
+ sw = QIXIS_READ(brdcfg[2]);
+ for (i = 0; i < MAX_SERDES; i++) {
+ static const char * const freq[] = {
+ "100", "125", "156.25", "161.1328125"};
+ unsigned int clock = (sw >> (6 - 2 * i)) & 3;
+
+ printf("SERDES%u=%sMHz ", i+1, freq[clock]);
+ }
+ puts("\n");
+
+ return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+/*
+ * read_voltage from sensor on I2C bus
+ * We use average of 4 readings, waiting for 532us befor another reading
+ */
+#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */
+#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */
+
+static inline int read_voltage(void)
+{
+ int i, ret, voltage_read = 0;
+ u16 vol_mon;
+
+ for (i = 0; i < NUM_READINGS; i++) {
+ ret = i2c_read(I2C_VOL_MONITOR_ADDR,
+ I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2);
+ if (ret) {
+ printf("VID: failed to read core voltage\n");
+ return ret;
+ }
+ if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) {
+ printf("VID: Core voltage sensor error\n");
+ return -1;
+ }
+ debug("VID: bus voltage reads 0x%04x\n", vol_mon);
+ /* LSB = 4mv */
+ voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4;
+ udelay(WAIT_FOR_ADC);
+ }
+ /* calculate the average */
+ voltage_read /= NUM_READINGS;
+
+ return voltage_read;
+}
+
+/*
+ * We need to calculate how long before the voltage starts to drop or increase
+ * It returns with the loop count. Each loop takes several readings (532us)
+ */
+static inline int wait_for_voltage_change(int vdd_last)
+{
+ int timeout, vdd_current;
+
+ vdd_current = read_voltage();
+ /* wait until voltage starts to drop */
+ for (timeout = 0; abs(vdd_last - vdd_current) <= 4 &&
+ timeout < 100; timeout++) {
+ vdd_current = read_voltage();
+ }
+ if (timeout >= 100) {
+ printf("VID: Voltage adjustment timeout\n");
+ return -1;
+ }
+ return timeout;
+}
+
+/*
+ * argument 'wait' is the time we know the voltage difference can be measured
+ * this function keeps reading the voltage until it is stable
+ */
+static inline int wait_for_voltage_stable(int wait)
+{
+ int timeout, vdd_current, vdd_last;
+
+ vdd_last = read_voltage();
+ udelay(wait * NUM_READINGS * WAIT_FOR_ADC);
+ /* wait until voltage is stable */
+ vdd_current = read_voltage();
+ for (timeout = 0; abs(vdd_last - vdd_current) >= 4 &&
+ timeout < 100; timeout++) {
+ vdd_last = vdd_current;
+ udelay(wait * NUM_READINGS * WAIT_FOR_ADC);
+ vdd_current = read_voltage();
+ }
+ if (timeout >= 100) {
+ printf("VID: Voltage adjustment timeout\n");
+ return -1;
+ }
+
+ return vdd_current;
+}
+
+static inline int set_voltage(u8 vid)
+{
+ int wait, vdd_last;
+
+ vdd_last = read_voltage();
+ QIXIS_WRITE(brdcfg[6], vid);
+ wait = wait_for_voltage_change(vdd_last);
+ if (wait < 0)
+ return -1;
+ debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC);
+ wait = wait ? wait : 1;
+
+ vdd_last = wait_for_voltage_stable(wait);
+ if (vdd_last < 0)
+ return -1;
+ debug("VID: Current voltage is %d mV\n", vdd_last);
+
+ return vdd_last;
+}
+
+
+static int adjust_vdd(ulong vdd_override)
+{
+ int re_enable = disable_interrupts();
+ ccsr_gur_t __iomem *gur =
+ (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 fusesr;
+ u8 vid, vid_current;
+ int vdd_target, vdd_current, vdd_last;
+ int ret;
+ unsigned long vdd_string_override;
+ char *vdd_string;
+ static const uint16_t vdd[32] = {
+ 0, /* unused */
+ 9875, /* 0.9875V */
+ 9750,
+ 9625,
+ 9500,
+ 9375,
+ 9250,
+ 9125,
+ 9000,
+ 8875,
+ 8750,
+ 8625,
+ 8500,
+ 8375,
+ 8250,
+ 8125,
+ 10000, /* 1.0000V */
+ 10125,
+ 10250,
+ 10375,
+ 10500,
+ 10625,
+ 10750,
+ 10875,
+ 11000,
+ 0, /* reserved */
+ };
+ struct vdd_drive {
+ u8 vid;
+ unsigned voltage;
+ };
+
+ ret = select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR);
+ if (ret) {
+ debug("VID: I2c failed to switch channel\n");
+ ret = -1;
+ goto exit;
+ }
+
+ /* get the voltage ID from fuse status register */
+ fusesr = in_be32(&gur->dcfg_fusesr);
+ vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) &
+ FSL_CORENET_DCFG_FUSESR_VID_MASK;
+ if (vid == FSL_CORENET_DCFG_FUSESR_VID_MASK) {
+ vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
+ FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
+ }
+ vdd_target = vdd[vid];
+
+ /* check override variable for overriding VDD */
+ vdd_string = getenv("t4240qds_vdd_mv");
+ if (vdd_override == 0 && vdd_string &&
+ !strict_strtoul(vdd_string, 10, &vdd_string_override))
+ vdd_override = vdd_string_override;
+ if (vdd_override >= 819 && vdd_override <= 1212) {
+ vdd_target = vdd_override * 10; /* convert to 1/10 mV */
+ debug("VDD override is %lu\n", vdd_override);
+ } else if (vdd_override != 0) {
+ printf("Invalid value.\n");
+ }
+
+ if (vdd_target == 0) {
+ debug("VID: VID not used\n");
+ ret = 0;
+ goto exit;
+ } else {
+ /* round up and divice by 10 to get a value in mV */
+ vdd_target = DIV_ROUND_UP(vdd_target, 10);
+ debug("VID: vid = %d mV\n", vdd_target);
+ }
+
+ /*
+ * Check current board VID setting
+ * Voltage regulator support output to 6.250mv step
+ * The highes voltage allowed for this board is (vid=0x40) 1.21250V
+ * the lowest is (vid=0x7f) 0.81875V
+ */
+ vid_current = QIXIS_READ(brdcfg[6]);
+ vdd_current = 121250 - (vid_current - 0x40) * 625;
+ debug("VID: Current vid setting is (0x%x) %d mV\n",
+ vid_current, vdd_current/100);
+
+ /*
+ * Read voltage monitor to check real voltage.
+ * Voltage monitor LSB is 4mv.
+ */
+ vdd_last = read_voltage();
+ if (vdd_last < 0) {
+ printf("VID: Could not read voltage sensor abort VID adjustment\n");
+ ret = -1;
+ goto exit;
+ }
+ debug("VID: Core voltage is at %d mV\n", vdd_last);
+ /*
+ * Adjust voltage to@or 8mV above target.
+ * Each step of adjustment is 6.25mV.
+ * Stepping down too fast may cause over current.
+ */
+ while (vdd_last > 0 && vid_current < 0x80 &&
+ vdd_last > (vdd_target + 8)) {
+ vid_current++;
+ vdd_last = set_voltage(vid_current);
+ }
+ /*
+ * Check if we need to step up
+ * This happens when board voltage switch was set too low
+ */
+ while (vdd_last > 0 && vid_current >= 0x40 &&
+ vdd_last < vdd_target + 2) {
+ vid_current--;
+ vdd_last = set_voltage(vid_current);
+ }
+ if (vdd_last > 0)
+ printf("VID: Core voltage %d mV\n", vdd_last);
+ else
+ ret = -1;
+
+exit:
+ if (re_enable)
+ enable_interrupts();
+ return ret;
+}
+
+/* Configure Crossbar switches for Front-Side SerDes Ports */
+int config_frontside_crossbar_vsc3316(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_prtcl_s1, srds_prtcl_s2;
+ int ret;
+
+ ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS);
+ if (ret)
+ return ret;
+
+ srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+ if (srds_prtcl_s1) {
+ ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm1_tx, 8);
+ if (ret)
+ return ret;
+ ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm1_rx, 8);
+ if (ret)
+ return ret;
+ }
+
+ srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+ srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+ if (srds_prtcl_s2) {
+ ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm2_tx, 8);
+ if (ret)
+ return ret;
+ ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm2_rx, 8);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+int config_backside_crossbar_mux(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_prtcl_s3, srds_prtcl_s4;
+ u8 brdcfg;
+
+ srds_prtcl_s3 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS3_PRTCL;
+ srds_prtcl_s3 >>= FSL_CORENET2_RCWSR4_SRDS3_PRTCL_SHIFT;
+ switch (srds_prtcl_s3) {
+ case 0:
+ /* SerDes3 is not enabled */
+ break;
+ case 2:
+ case 9:
+ case 10:
+ /* SD3(0:7) => SLOT5(0:7) */
+ brdcfg = QIXIS_READ(brdcfg[12]);
+ brdcfg &= ~BRDCFG12_SD3MX_MASK;
+ brdcfg |= BRDCFG12_SD3MX_SLOT5;
+ QIXIS_WRITE(brdcfg[12], brdcfg);
+ break;
+ case 4:
+ case 6:
+ case 8:
+ case 12:
+ case 14:
+ case 16:
+ case 17:
+ case 19:
+ case 20:
+ /* SD3(4:7) => SLOT6(0:3) */
+ brdcfg = QIXIS_READ(brdcfg[12]);
+ brdcfg &= ~BRDCFG12_SD3MX_MASK;
+ brdcfg |= BRDCFG12_SD3MX_SLOT6;
+ QIXIS_WRITE(brdcfg[12], brdcfg);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes3 Protocol %d\n",
+ srds_prtcl_s3);
+ return -1;
+ }
+
+ srds_prtcl_s4 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS4_PRTCL;
+ srds_prtcl_s4 >>= FSL_CORENET2_RCWSR4_SRDS4_PRTCL_SHIFT;
+ switch (srds_prtcl_s4) {
+ case 0:
+ /* SerDes4 is not enabled */
+ break;
+ case 2:
+ /* 10b, SD4(0:7) => SLOT7(0:7) */
+ brdcfg = QIXIS_READ(brdcfg[12]);
+ brdcfg &= ~BRDCFG12_SD4MX_MASK;
+ brdcfg |= BRDCFG12_SD4MX_SLOT7;
+ QIXIS_WRITE(brdcfg[12], brdcfg);
+ break;
+ case 4:
+ case 6:
+ case 8:
+ /* x1b, SD4(4:7) => SLOT8(0:3) */
+ brdcfg = QIXIS_READ(brdcfg[12]);
+ brdcfg &= ~BRDCFG12_SD4MX_MASK;
+ brdcfg |= BRDCFG12_SD4MX_SLOT8;
+ QIXIS_WRITE(brdcfg[12], brdcfg);
+ break;
+ case 10:
+ case 12:
+ case 14:
+ case 16:
+ case 18:
+ /* 00b, SD4(4:5) => AURORA, SD4(6:7) => SATA */
+ brdcfg = QIXIS_READ(brdcfg[12]);
+ brdcfg &= ~BRDCFG12_SD4MX_MASK;
+ brdcfg |= BRDCFG12_SD4MX_AURO_SATA;
+ QIXIS_WRITE(brdcfg[12], brdcfg);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes4 Protocol %d\n",
+ srds_prtcl_s4);
+ return -1;
+ }
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ /* Disable remote I2C connection to qixis fpga */
+ QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE);
+
+ /*
+ * Adjust core voltage according to voltage ID
+ * This function changes I2C mux to channel 2.
+ */
+ if (adjust_vdd(0))
+ printf("Warning: Adjusting core voltage failed.\n");
+
+ /* Configure board SERDES ports crossbar */
+ config_frontside_crossbar_vsc3316();
+ config_backside_crossbar_mux();
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+ /* use accurate clock measurement */
+ int freq = QIXIS_READ(clk_freq[0]) << 8 | QIXIS_READ(clk_freq[1]);
+ int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+ u32 val;
+
+ val = freq * base;
+ if (val) {
+ debug("SYS Clock measurement is: %d\n", val);
+ return val;
+ } else {
+ printf("Warning: SYS clock measurement is invalid, using value from brdcfg1.\n");
+ }
+#endif
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+ /* use accurate clock measurement */
+ int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]);
+ int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+ u32 val;
+
+ val = freq * base;
+ if (val) {
+ debug("DDR Clock measurement is: %d\n", val);
+ return val;
+ } else {
+ printf("Warning: DDR clock measurement is invalid, using value from brdcfg1.\n");
+ }
+#endif
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+ switch (clock) {
+ case SRDS_PLLCR0_RFCK_SEL_100:
+ return "100";
+ case SRDS_PLLCR0_RFCK_SEL_125:
+ return "125";
+ case SRDS_PLLCR0_RFCK_SEL_156_25:
+ return "156.25";
+ case SRDS_PLLCR0_RFCK_SEL_161_13:
+ return "161.1328125";
+ default:
+ return "???";
+ }
+}
+
+int misc_init_r(void)
+{
+ u8 sw;
+ serdes_corenet_t *srds_regs =
+ (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+ u32 actual[MAX_SERDES];
+ unsigned int i;
+
+ sw = QIXIS_READ(brdcfg[2]);
+ for (i = 0; i < MAX_SERDES; i++) {
+ unsigned int clock = (sw >> (6 - 2 * i)) & 3;
+ switch (clock) {
+ case 0:
+ actual[i] = SRDS_PLLCR0_RFCK_SEL_100;
+ break;
+ case 1:
+ actual[i] = SRDS_PLLCR0_RFCK_SEL_125;
+ break;
+ case 2:
+ actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25;
+ break;
+ case 3:
+ actual[i] = SRDS_PLLCR0_RFCK_SEL_161_13;
+ break;
+ }
+ }
+
+ for (i = 0; i < MAX_SERDES; i++) {
+ u32 pllcr0 = srds_regs->bank[i].pllcr0;
+ u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
+ if (expected != actual[i]) {
+ printf("Warning: SERDES%u expects reference clock"
+ " %sMHz, but actual is %sMHz\n", i + 1,
+ serdes_clock_to_string(expected),
+ serdes_clock_to_string(actual[i]));
+ }
+ }
+
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+}
+
+/*
+ * This function is called by bdinfo to print detail board information.
+ * As an exmaple for future board, we organize the messages into
+ * several sections. If applicable, the message is in the format of
+ * <name> = <value>
+ * It should aligned with normal output of bdinfo command.
+ *
+ * Voltage: Core, DDR and another configurable voltages
+ * Clock : Critical clocks which are not printed already
+ * RCW : RCW source if not printed already
+ * Misc : Other important information not in above catagories
+ */
+void board_detail(void)
+{
+ int i;
+ u8 brdcfg[16], dutcfg[16], rst_ctl;
+ int vdd, rcwsrc;
+ static const char * const clk[] = {"66.67", "100", "125", "133.33"};
+
+ for (i = 0; i < 16; i++) {
+ brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i);
+ dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i);
+ }
+
+ /* Voltage secion */
+ if (!select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR)) {
+ vdd = read_voltage();
+ if (vdd > 0)
+ printf("Core voltage= %d mV\n", vdd);
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+ }
+
+ printf("XVDD = 1.%d V\n", ((brdcfg[8] & 0xf) - 4) * 5 + 25);
+
+ /* clock section */
+ printf("SYSCLK = %s MHz\nDDRCLK = %s MHz\n",
+ clk[(brdcfg[11] >> 2) & 0x3], clk[brdcfg[11] & 3]);
+
+ /* RCW section */
+ rcwsrc = (dutcfg[0] << 1) + (dutcfg[1] & 1);
+ puts("RCW source = ");
+ switch (rcwsrc) {
+ case 0x017:
+ case 0x01f:
+ puts("8-bit NOR\n");
+ break;
+ case 0x027:
+ case 0x02F:
+ puts("16-bit NOR\n");
+ break;
+ case 0x040:
+ puts("SDHC/eMMC\n");
+ break;
+ case 0x044:
+ puts("SPI 16-bit addressing\n");
+ break;
+ case 0x045:
+ puts("SPI 24-bit addressing\n");
+ break;
+ case 0x048:
+ puts("I2C normal addressing\n");
+ break;
+ case 0x049:
+ puts("I2C extended addressing\n");
+ break;
+ case 0x108:
+ case 0x109:
+ case 0x10a:
+ case 0x10b:
+ puts("8-bit NAND, 2KB\n");
+ break;
+ default:
+ if ((rcwsrc >= 0x080) && (rcwsrc <= 0x09f))
+ puts("Hard-coded RCW\n");
+ else if ((rcwsrc >= 0x110) && (rcwsrc <= 0x11f))
+ puts("8-bit NAND, 4KB\n");
+ else
+ puts("unknown\n");
+ break;
+ }
+
+ /* Misc section */
+ rst_ctl = QIXIS_READ(rst_ctl);
+ puts("HRESET_REQ = ");
+ switch (rst_ctl & 0x30) {
+ case 0x00:
+ puts("Ignored\n");
+ break;
+ case 0x10:
+ puts("Assert HRESET\n");
+ break;
+ case 0x30:
+ puts("Reset system\n");
+ break;
+ default:
+ puts("N/A\n");
+ break;
+ }
+}
+
+/*
+ * Reverse engineering switch settings.
+ * Some bits cannot be figured out. They will be displayed as
+ * underscore in binary format. mask[] has those bits.
+ * Some bits are calculated differently than the actual switches
+ * if booting with overriding by FPGA.
+ */
+void qixis_dump_switch(void)
+{
+ int i;
+ u8 sw[9];
+
+ /*
+ * Any bit with 1 means that bit cannot be reverse engineered.
+ * It will be displayed as _ in binary format.
+ */
+ static const u8 mask[] = {0, 0, 0, 0, 0, 0x1, 0xcf, 0x3f, 0x1f};
+ char buf[10];
+ u8 brdcfg[16], dutcfg[16];
+
+ for (i = 0; i < 16; i++) {
+ brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i);
+ dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i);
+ }
+
+ sw[0] = dutcfg[0];
+ sw[1] = (dutcfg[1] << 0x07) | \
+ ((dutcfg[12] & 0xC0) >> 1) | \
+ ((dutcfg[11] & 0xE0) >> 3) | \
+ ((dutcfg[6] & 0x80) >> 6) | \
+ ((dutcfg[1] & 0x80) >> 7);
+ sw[2] = ((brdcfg[1] & 0x0f) << 4) | \
+ ((brdcfg[1] & 0x30) >> 2) | \
+ ((brdcfg[1] & 0x40) >> 5) | \
+ ((brdcfg[1] & 0x80) >> 7);
+ sw[3] = brdcfg[2];
+ sw[4] = ((dutcfg[2] & 0x01) << 7) | \
+ ((dutcfg[2] & 0x06) << 4) | \
+ ((~QIXIS_READ(present)) & 0x10) | \
+ ((brdcfg[3] & 0x80) >> 4) | \
+ ((brdcfg[3] & 0x01) << 2) | \
+ ((brdcfg[6] == 0x62) ? 3 : \
+ ((brdcfg[6] == 0x5a) ? 2 : \
+ ((brdcfg[6] == 0x5e) ? 1 : 0)));
+ sw[5] = ((brdcfg[0] & 0x0f) << 4) | \
+ ((QIXIS_READ(rst_ctl) & 0x30) >> 2) | \
+ ((brdcfg[0] & 0x40) >> 5);
+ sw[6] = (brdcfg[11] & 0x20) |
+ ((brdcfg[5] & 0x02) << 3);
+ sw[7] = (((~QIXIS_READ(rst_ctl)) & 0x40) << 1) | \
+ ((brdcfg[5] & 0x10) << 2);
+ sw[8] = ((brdcfg[12] & 0x08) << 4) | \
+ ((brdcfg[12] & 0x03) << 5);
+
+ puts("DIP switch (reverse-engineering)\n");
+ for (i = 0; i < 9; i++) {
+ printf("SW%d = 0b%s (0x%02x)\n",
+ i + 1, byte_to_binary_mask(sw[i], mask[i], buf), sw[i]);
+ }
+}
+
+static int do_vdd_adjust(cmd_tbl_t *cmdtp,
+ int flag, int argc,
+ char * const argv[])
+{
+ ulong override;
+
+ if (argc < 2)
+ return CMD_RET_USAGE;
+ if (!strict_strtoul(argv[1], 10, &override))
+ adjust_vdd(override); /* the value is checked by callee */
+ else
+ return CMD_RET_USAGE;
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ vdd_override, 2, 0, do_vdd_adjust,
+ "Override VDD",
+ "- override with the voltage specified in mV, eg. 1050"
+);
diff --git a/board/freescale/t4qds/t4qds.c b/board/freescale/t4qds/t4qds.c
deleted file mode 100644
index 67de0ea..0000000
--- a/board/freescale/t4qds/t4qds.c
+++ /dev/null
@@ -1,853 +0,0 @@
-/*
- * Copyright 2009-2012 Freescale Semiconductor, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <command.h>
-#include <i2c.h>
-#include <netdev.h>
-#include <linux/compiler.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_portals.h>
-#include <asm/fsl_liodn.h>
-#include <fm_eth.h>
-
-#include "../common/qixis.h"
-#include "../common/vsc3316_3308.h"
-#include "t4qds.h"
-#include "t4240qds_qixis.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static const int8_t vsc3316_fsm1_tx[8][2] = { {0, 0}, {1, 1}, {6, 6}, {7, 7},
- {8, 8}, {9, 9}, {14, 14}, {15, 15} };
-
-static const int8_t vsc3316_fsm2_tx[8][2] = { {2, 2}, {3, 3}, {4, 4}, {5, 5},
- {10, 10}, {11, 11}, {12, 12}, {13, 13} };
-
-static const int8_t vsc3316_fsm1_rx[8][2] = { {2, 12}, {3, 13}, {4, 5}, {5, 4},
- {10, 11}, {11, 10}, {12, 2}, {13, 3} };
-
-static const int8_t vsc3316_fsm2_rx[8][2] = { {0, 15}, {1, 14}, {6, 7}, {7, 6},
- {8, 9}, {9, 8}, {14, 1}, {15, 0} };
-
-int checkboard(void)
-{
- char buf[64];
- u8 sw;
- struct cpu_type *cpu = gd->arch.cpu;
- unsigned int i;
-
- printf("Board: %sQDS, ", cpu->name);
- printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ",
- QIXIS_READ(id), QIXIS_READ(arch));
-
- sw = QIXIS_READ(brdcfg[0]);
- sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
-
- if (sw < 0x8)
- printf("vBank: %d\n", sw);
- else if (sw == 0x8)
- puts("Promjet\n");
- else if (sw == 0x9)
- puts("NAND\n");
- else
- printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
-
- printf("FPGA: v%d (%s), build %d",
- (int)QIXIS_READ(scver), qixis_read_tag(buf),
- (int)qixis_read_minor());
- /* the timestamp string contains "\n"@the end */
- printf(" on %s", qixis_read_time(buf));
-
- /*
- * Display the actual SERDES reference clocks as configured by the
- * dip switches on the board. Note that the SWx registers could
- * technically be set to force the reference clocks to match the
- * values that the SERDES expects (or vice versa). For now, however,
- * we just display both values and hope the user notices when they
- * don't match.
- */
- puts("SERDES Reference Clocks: ");
- sw = QIXIS_READ(brdcfg[2]);
- for (i = 0; i < MAX_SERDES; i++) {
- static const char *freq[] = {
- "100", "125", "156.25", "161.1328125"};
- unsigned int clock = (sw >> (6 - 2 * i)) & 3;
-
- printf("SERDES%u=%sMHz ", i+1, freq[clock]);
- }
- puts("\n");
-
- return 0;
-}
-
-int select_i2c_ch_pca9547(u8 ch)
-{
- int ret;
-
- ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
- if (ret) {
- puts("PCA: failed to select proper channel\n");
- return ret;
- }
-
- return 0;
-}
-
-/*
- * read_voltage from sensor on I2C bus
- * We use average of 4 readings, waiting for 532us befor another reading
- */
-#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */
-#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */
-
-static inline int read_voltage(void)
-{
- int i, ret, voltage_read = 0;
- u16 vol_mon;
-
- for (i = 0; i < NUM_READINGS; i++) {
- ret = i2c_read(I2C_VOL_MONITOR_ADDR,
- I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2);
- if (ret) {
- printf("VID: failed to read core voltage\n");
- return ret;
- }
- if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) {
- printf("VID: Core voltage sensor error\n");
- return -1;
- }
- debug("VID: bus voltage reads 0x%04x\n", vol_mon);
- /* LSB = 4mv */
- voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4;
- udelay(WAIT_FOR_ADC);
- }
- /* calculate the average */
- voltage_read /= NUM_READINGS;
-
- return voltage_read;
-}
-
-/*
- * We need to calculate how long before the voltage starts to drop or increase
- * It returns with the loop count. Each loop takes several readings (532us)
- */
-static inline int wait_for_voltage_change(int vdd_last)
-{
- int timeout, vdd_current;
-
- vdd_current = read_voltage();
- /* wait until voltage starts to drop */
- for (timeout = 0; abs(vdd_last - vdd_current) <= 4 &&
- timeout < 100; timeout++) {
- vdd_current = read_voltage();
- }
- if (timeout >= 100) {
- printf("VID: Voltage adjustment timeout\n");
- return -1;
- }
- return timeout;
-}
-
-/*
- * argument 'wait' is the time we know the voltage difference can be measured
- * this function keeps reading the voltage until it is stable
- */
-static inline int wait_for_voltage_stable(int wait)
-{
- int timeout, vdd_current, vdd_last;
-
- vdd_last = read_voltage();
- udelay(wait * NUM_READINGS * WAIT_FOR_ADC);
- /* wait until voltage is stable */
- vdd_current = read_voltage();
- for (timeout = 0; abs(vdd_last - vdd_current) >= 4 &&
- timeout < 100; timeout++) {
- vdd_last = vdd_current;
- udelay(wait * NUM_READINGS * WAIT_FOR_ADC);
- vdd_current = read_voltage();
- }
- if (timeout >= 100) {
- printf("VID: Voltage adjustment timeout\n");
- return -1;
- }
-
- return vdd_current;
-}
-
-static inline int set_voltage(u8 vid)
-{
- int wait, vdd_last;
-
- vdd_last = read_voltage();
- QIXIS_WRITE(brdcfg[6], vid);
- wait = wait_for_voltage_change(vdd_last);
- if (wait < 0)
- return -1;
- debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC);
- wait = wait ? wait : 1;
-
- vdd_last = wait_for_voltage_stable(wait);
- if (vdd_last < 0)
- return -1;
- debug("VID: Current voltage is %d mV\n", vdd_last);
-
- return vdd_last;
-}
-
-
-static int adjust_vdd(ulong vdd_override)
-{
- int re_enable = disable_interrupts();
- ccsr_gur_t __iomem *gur =
- (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 fusesr;
- u8 vid, vid_current;
- int vdd_target, vdd_current, vdd_last;
- int ret;
- unsigned long vdd_string_override;
- char *vdd_string;
- static const uint16_t vdd[32] = {
- 0, /* unused */
- 9875, /* 0.9875V */
- 9750,
- 9625,
- 9500,
- 9375,
- 9250,
- 9125,
- 9000,
- 8875,
- 8750,
- 8625,
- 8500,
- 8375,
- 8250,
- 8125,
- 10000, /* 1.0000V */
- 10125,
- 10250,
- 10375,
- 10500,
- 10625,
- 10750,
- 10875,
- 11000,
- 0, /* reserved */
- };
- struct vdd_drive {
- u8 vid;
- unsigned voltage;
- };
-
- ret = select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR);
- if (ret) {
- debug("VID: I2c failed to switch channel\n");
- ret = -1;
- goto exit;
- }
-
- /* get the voltage ID from fuse status register */
- fusesr = in_be32(&gur->dcfg_fusesr);
- vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) &
- FSL_CORENET_DCFG_FUSESR_VID_MASK;
- if (vid == FSL_CORENET_DCFG_FUSESR_VID_MASK) {
- vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
- FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
- }
- vdd_target = vdd[vid];
-
- /* check override variable for overriding VDD */
- vdd_string = getenv("t4240qds_vdd_mv");
- if (vdd_override == 0 && vdd_string &&
- !strict_strtoul(vdd_string, 10, &vdd_string_override))
- vdd_override = vdd_string_override;
- if (vdd_override >= 819 && vdd_override <= 1212) {
- vdd_target = vdd_override * 10; /* convert to 1/10 mV */
- debug("VDD override is %lu\n", vdd_override);
- } else if (vdd_override != 0) {
- printf("Invalid value.\n");
- }
-
- if (vdd_target == 0) {
- debug("VID: VID not used\n");
- ret = 0;
- goto exit;
- } else {
- /* round up and divice by 10 to get a value in mV */
- vdd_target = DIV_ROUND_UP(vdd_target, 10);
- debug("VID: vid = %d mV\n", vdd_target);
- }
-
- /*
- * Check current board VID setting
- * Voltage regulator support output to 6.250mv step
- * The highes voltage allowed for this board is (vid=0x40) 1.21250V
- * the lowest is (vid=0x7f) 0.81875V
- */
- vid_current = QIXIS_READ(brdcfg[6]);
- vdd_current = 121250 - (vid_current - 0x40) * 625;
- debug("VID: Current vid setting is (0x%x) %d mV\n",
- vid_current, vdd_current/100);
-
- /*
- * Read voltage monitor to check real voltage.
- * Voltage monitor LSB is 4mv.
- */
- vdd_last = read_voltage();
- if (vdd_last < 0) {
- printf("VID: Could not read voltage sensor abort VID adjustment\n");
- ret = -1;
- goto exit;
- }
- debug("VID: Core voltage is at %d mV\n", vdd_last);
- /*
- * Adjust voltage to@or 8mV above target.
- * Each step of adjustment is 6.25mV.
- * Stepping down too fast may cause over current.
- */
- while (vdd_last > 0 && vid_current < 0x80 &&
- vdd_last > (vdd_target + 8)) {
- vid_current++;
- vdd_last = set_voltage(vid_current);
- }
- /*
- * Check if we need to step up
- * This happens when board voltage switch was set too low
- */
- while (vdd_last > 0 && vid_current >= 0x40 &&
- vdd_last < vdd_target + 2) {
- vid_current--;
- vdd_last = set_voltage(vid_current);
- }
- if (vdd_last > 0)
- printf("VID: Core voltage %d mV\n", vdd_last);
- else
- ret = -1;
-
-exit:
- if (re_enable)
- enable_interrupts();
- return ret;
-}
-
-/* Configure Crossbar switches for Front-Side SerDes Ports */
-int config_frontside_crossbar_vsc3316(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_prtcl_s1, srds_prtcl_s2;
- int ret;
-
- ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS);
- if (ret)
- return ret;
-
- srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
- if (srds_prtcl_s1) {
- ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm1_tx, 8);
- if (ret)
- return ret;
- ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm1_rx, 8);
- if (ret)
- return ret;
- }
-
- srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
- srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
- if (srds_prtcl_s2) {
- ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm2_tx, 8);
- if (ret)
- return ret;
- ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm2_rx, 8);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-
-int config_backside_crossbar_mux(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_prtcl_s3, srds_prtcl_s4;
- u8 brdcfg;
-
- srds_prtcl_s3 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS3_PRTCL;
- srds_prtcl_s3 >>= FSL_CORENET2_RCWSR4_SRDS3_PRTCL_SHIFT;
- switch (srds_prtcl_s3) {
- case 0:
- /* SerDes3 is not enabled */
- break;
- case 2:
- case 9:
- case 10:
- /* SD3(0:7) => SLOT5(0:7) */
- brdcfg = QIXIS_READ(brdcfg[12]);
- brdcfg &= ~BRDCFG12_SD3MX_MASK;
- brdcfg |= BRDCFG12_SD3MX_SLOT5;
- QIXIS_WRITE(brdcfg[12], brdcfg);
- break;
- case 4:
- case 6:
- case 8:
- case 12:
- case 14:
- case 16:
- case 17:
- case 19:
- case 20:
- /* SD3(4:7) => SLOT6(0:3) */
- brdcfg = QIXIS_READ(brdcfg[12]);
- brdcfg &= ~BRDCFG12_SD3MX_MASK;
- brdcfg |= BRDCFG12_SD3MX_SLOT6;
- QIXIS_WRITE(brdcfg[12], brdcfg);
- break;
- default:
- printf("WARNING: unsupported for SerDes3 Protocol %d\n",
- srds_prtcl_s3);
- return -1;
- }
-
- srds_prtcl_s4 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS4_PRTCL;
- srds_prtcl_s4 >>= FSL_CORENET2_RCWSR4_SRDS4_PRTCL_SHIFT;
- switch (srds_prtcl_s4) {
- case 0:
- /* SerDes4 is not enabled */
- break;
- case 2:
- /* 10b, SD4(0:7) => SLOT7(0:7) */
- brdcfg = QIXIS_READ(brdcfg[12]);
- brdcfg &= ~BRDCFG12_SD4MX_MASK;
- brdcfg |= BRDCFG12_SD4MX_SLOT7;
- QIXIS_WRITE(brdcfg[12], brdcfg);
- break;
- case 4:
- case 6:
- case 8:
- /* x1b, SD4(4:7) => SLOT8(0:3) */
- brdcfg = QIXIS_READ(brdcfg[12]);
- brdcfg &= ~BRDCFG12_SD4MX_MASK;
- brdcfg |= BRDCFG12_SD4MX_SLOT8;
- QIXIS_WRITE(brdcfg[12], brdcfg);
- break;
- case 10:
- case 12:
- case 14:
- case 16:
- case 18:
- /* 00b, SD4(4:5) => AURORA, SD4(6:7) => SATA */
- brdcfg = QIXIS_READ(brdcfg[12]);
- brdcfg &= ~BRDCFG12_SD4MX_MASK;
- brdcfg |= BRDCFG12_SD4MX_AURO_SATA;
- QIXIS_WRITE(brdcfg[12], brdcfg);
- break;
- default:
- printf("WARNING: unsupported for SerDes4 Protocol %d\n",
- srds_prtcl_s4);
- return -1;
- }
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
- const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
-
- /*
- * Remap Boot flash + PROMJET region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- /* invalidate existing TLB entry for flash + promjet */
- disable_tlb(flash_esel);
-
- set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_256M, 1);
-
- set_liodns();
-#ifdef CONFIG_SYS_DPAA_QBMAN
- setup_portals();
-#endif
-
- /* Disable remote I2C connection to qixis fpga */
- QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE);
-
- /*
- * Adjust core voltage according to voltage ID
- * This function changes I2C mux to channel 2.
- */
- if (adjust_vdd(0))
- printf("Warning: Adjusting core voltage failed.\n");
-
- /* Configure board SERDES ports crossbar */
- config_frontside_crossbar_vsc3316();
- config_backside_crossbar_mux();
- select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
-
- return 0;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
-#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
- /* use accurate clock measurement */
- int freq = QIXIS_READ(clk_freq[0]) << 8 | QIXIS_READ(clk_freq[1]);
- int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
- u32 val;
-
- val = freq * base;
- if (val) {
- debug("SYS Clock measurement is: %d\n", val);
- return val;
- } else {
- printf("Warning: SYS clock measurement is invalid, using value from brdcfg1.\n");
- }
-#endif
-
- switch (sysclk_conf & 0x0F) {
- case QIXIS_SYSCLK_83:
- return 83333333;
- case QIXIS_SYSCLK_100:
- return 100000000;
- case QIXIS_SYSCLK_125:
- return 125000000;
- case QIXIS_SYSCLK_133:
- return 133333333;
- case QIXIS_SYSCLK_150:
- return 150000000;
- case QIXIS_SYSCLK_160:
- return 160000000;
- case QIXIS_SYSCLK_166:
- return 166666666;
- }
- return 66666666;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
-#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
- /* use accurate clock measurement */
- int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]);
- int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
- u32 val;
-
- val = freq * base;
- if (val) {
- debug("DDR Clock measurement is: %d\n", val);
- return val;
- } else {
- printf("Warning: DDR clock measurement is invalid, using value from brdcfg1.\n");
- }
-#endif
-
- switch ((ddrclk_conf & 0x30) >> 4) {
- case QIXIS_DDRCLK_100:
- return 100000000;
- case QIXIS_DDRCLK_125:
- return 125000000;
- case QIXIS_DDRCLK_133:
- return 133333333;
- }
- return 66666666;
-}
-
-static const char *serdes_clock_to_string(u32 clock)
-{
- switch (clock) {
- case SRDS_PLLCR0_RFCK_SEL_100:
- return "100";
- case SRDS_PLLCR0_RFCK_SEL_125:
- return "125";
- case SRDS_PLLCR0_RFCK_SEL_156_25:
- return "156.25";
- case SRDS_PLLCR0_RFCK_SEL_161_13:
- return "161.1328125";
- default:
- return "???";
- }
-}
-
-int misc_init_r(void)
-{
- u8 sw;
- serdes_corenet_t *srds_regs =
- (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
- u32 actual[MAX_SERDES];
- unsigned int i;
-
- sw = QIXIS_READ(brdcfg[2]);
- for (i = 0; i < MAX_SERDES; i++) {
- unsigned int clock = (sw >> (6 - 2 * i)) & 3;
- switch (clock) {
- case 0:
- actual[i] = SRDS_PLLCR0_RFCK_SEL_100;
- break;
- case 1:
- actual[i] = SRDS_PLLCR0_RFCK_SEL_125;
- break;
- case 2:
- actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25;
- break;
- case 3:
- actual[i] = SRDS_PLLCR0_RFCK_SEL_161_13;
- break;
- }
- }
-
- for (i = 0; i < MAX_SERDES; i++) {
- u32 pllcr0 = srds_regs->bank[i].pllcr0;
- u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
- if (expected != actual[i]) {
- printf("Warning: SERDES%u expects reference clock"
- " %sMHz, but actual is %sMHz\n", i + 1,
- serdes_clock_to_string(expected),
- serdes_clock_to_string(actual[i]));
- }
- }
-
- return 0;
-}
-
-void ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = getenv_bootm_low();
- size = getenv_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#ifdef CONFIG_PCI
- pci_of_setup(blob, bd);
-#endif
-
- fdt_fixup_liodn(blob);
- fdt_fixup_dr_usb(blob, bd);
-
-#ifdef CONFIG_SYS_DPAA_FMAN
- fdt_fixup_fman_ethernet(blob);
- fdt_fixup_board_enet(blob);
-#endif
-}
-
-/*
- * This function is called by bdinfo to print detail board information.
- * As an exmaple for future board, we organize the messages into
- * several sections. If applicable, the message is in the format of
- * <name> = <value>
- * It should aligned with normal output of bdinfo command.
- *
- * Voltage: Core, DDR and another configurable voltages
- * Clock : Critical clocks which are not printed already
- * RCW : RCW source if not printed already
- * Misc : Other important information not in above catagories
- */
-void board_detail(void)
-{
- int i;
- u8 brdcfg[16], dutcfg[16], rst_ctl;
- int vdd, rcwsrc;
- static const char * const clk[] = {"66.67", "100", "125", "133.33"};
-
- for (i = 0; i < 16; i++) {
- brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i);
- dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i);
- }
-
- /* Voltage secion */
- if (!select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR)) {
- vdd = read_voltage();
- if (vdd > 0)
- printf("Core voltage= %d mV\n", vdd);
- select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
- }
-
- printf("XVDD = 1.%d V\n", ((brdcfg[8] & 0xf) - 4) * 5 + 25);
-
- /* clock section */
- printf("SYSCLK = %s MHz\nDDRCLK = %s MHz\n",
- clk[(brdcfg[11] >> 2) & 0x3], clk[brdcfg[11] & 3]);
-
- /* RCW section */
- rcwsrc = (dutcfg[0] << 1) + (dutcfg[1] & 1);
- puts("RCW source = ");
- switch (rcwsrc) {
- case 0x017:
- case 0x01f:
- puts("8-bit NOR\n");
- break;
- case 0x027:
- case 0x02F:
- puts("16-bit NOR\n");
- break;
- case 0x040:
- puts("SDHC/eMMC\n");
- break;
- case 0x044:
- puts("SPI 16-bit addressing\n");
- break;
- case 0x045:
- puts("SPI 24-bit addressing\n");
- break;
- case 0x048:
- puts("I2C normal addressing\n");
- break;
- case 0x049:
- puts("I2C extended addressing\n");
- break;
- case 0x108:
- case 0x109:
- case 0x10a:
- case 0x10b:
- puts("8-bit NAND, 2KB\n");
- break;
- default:
- if ((rcwsrc >= 0x080) && (rcwsrc <= 0x09f))
- puts("Hard-coded RCW\n");
- else if ((rcwsrc >= 0x110) && (rcwsrc <= 0x11f))
- puts("8-bit NAND, 4KB\n");
- else
- puts("unknown\n");
- break;
- }
-
- /* Misc section */
- rst_ctl = QIXIS_READ(rst_ctl);
- puts("HRESET_REQ = ");
- switch (rst_ctl & 0x30) {
- case 0x00:
- puts("Ignored\n");
- break;
- case 0x10:
- puts("Assert HRESET\n");
- break;
- case 0x30:
- puts("Reset system\n");
- break;
- default:
- puts("N/A\n");
- break;
- }
-}
-
-/*
- * Reverse engineering switch settings.
- * Some bits cannot be figured out. They will be displayed as
- * underscore in binary format. mask[] has those bits.
- * Some bits are calculated differently than the actual switches
- * if booting with overriding by FPGA.
- */
-void qixis_dump_switch(void)
-{
- int i;
- u8 sw[9];
-
- /*
- * Any bit with 1 means that bit cannot be reverse engineered.
- * It will be displayed as _ in binary format.
- */
- static const u8 mask[] = {0, 0, 0, 0, 0, 0x1, 0xcf, 0x3f, 0x1f};
- char buf[10];
- u8 brdcfg[16], dutcfg[16];
-
- for (i = 0; i < 16; i++) {
- brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i);
- dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i);
- }
-
- sw[0] = dutcfg[0];
- sw[1] = (dutcfg[1] << 0x07) | \
- ((dutcfg[12] & 0xC0) >> 1) | \
- ((dutcfg[11] & 0xE0) >> 3) | \
- ((dutcfg[6] & 0x80) >> 6) | \
- ((dutcfg[1] & 0x80) >> 7);
- sw[2] = ((brdcfg[1] & 0x0f) << 4) | \
- ((brdcfg[1] & 0x30) >> 2) | \
- ((brdcfg[1] & 0x40) >> 5) | \
- ((brdcfg[1] & 0x80) >> 7);
- sw[3] = brdcfg[2];
- sw[4] = ((dutcfg[2] & 0x01) << 7) | \
- ((dutcfg[2] & 0x06) << 4) | \
- ((~QIXIS_READ(present)) & 0x10) | \
- ((brdcfg[3] & 0x80) >> 4) | \
- ((brdcfg[3] & 0x01) << 2) | \
- ((brdcfg[6] == 0x62) ? 3 : \
- ((brdcfg[6] == 0x5a) ? 2 : \
- ((brdcfg[6] == 0x5e) ? 1 : 0)));
- sw[5] = ((brdcfg[0] & 0x0f) << 4) | \
- ((QIXIS_READ(rst_ctl) & 0x30) >> 2) | \
- ((brdcfg[0] & 0x40) >> 5);
- sw[6] = (brdcfg[11] & 0x20) |
- ((brdcfg[5] & 0x02) << 3);
- sw[7] = (((~QIXIS_READ(rst_ctl)) & 0x40) << 1) | \
- ((brdcfg[5] & 0x10) << 2);
- sw[8] = ((brdcfg[12] & 0x08) << 4) | \
- ((brdcfg[12] & 0x03) << 5);
-
- puts("DIP switch (reverse-engineering)\n");
- for (i = 0; i < 9; i++) {
- printf("SW%d = 0b%s (0x%02x)\n",
- i + 1, byte_to_binary_mask(sw[i], mask[i], buf), sw[i]);
- }
-}
-
-static int do_vdd_adjust(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- ulong override;
-
- if (argc < 2)
- return CMD_RET_USAGE;
- if (!strict_strtoul(argv[1], 10, &override))
- adjust_vdd(override); /* the value is checked by callee */
- else
- return CMD_RET_USAGE;
-
- return 0;
-}
-
-U_BOOT_CMD(
- vdd_override, 2, 0, do_vdd_adjust,
- "Override VDD",
- "- override with the voltage specified in mV, eg. 1050"
-);
diff --git a/board/freescale/t4qds/tlb.c b/board/freescale/t4qds/tlb.c
index 92c01cf..08bf1f0 100644
--- a/board/freescale/t4qds/tlb.c
+++ b/board/freescale/t4qds/tlb.c
@@ -127,10 +127,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 16, BOOKE_PAGESZ_64K, 1),
#endif
+#ifdef QIXIS_BASE_PHYS
SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 17, BOOKE_PAGESZ_4K, 1),
-
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index 1e598cb..6a1d56b 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -910,6 +910,7 @@ stxgp3 powerpc mpc85xx stxgp3 stx
stxssa powerpc mpc85xx stxssa stx - stxssa
stxssa_4M powerpc mpc85xx stxssa stx - stxssa:STXSSA_4M
T4240QDS powerpc mpc85xx t4qds freescale - T4240QDS:PPC_T4240
+T4240EMU powerpc mpc85xx t4qds freescale - T4240EMU:PPC_T4240
T4240QDS_SDCARD powerpc mpc85xx t4qds freescale - T4240QDS:PPC_T4240,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
T4240QDS_SPIFLASH powerpc mpc85xx t4qds freescale - T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
T4160QDS powerpc mpc85xx t4qds freescale - T4240QDS:PPC_T4160
diff --git a/include/configs/T4240EMU.h b/include/configs/T4240EMU.h
new file mode 100644
index 0000000..399e878
--- /dev/null
+++ b/include/configs/T4240EMU.h
@@ -0,0 +1,185 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * T4240 EMU board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_T4240EMU
+#define CONFIG_PHYS_64BIT
+
+#define CONFIG_SYS_NO_FLASH 1
+#define CONFIG_SYS_FSL_DDR_EMU 1
+#define CONFIG_SYS_FSL_NO_QIXIS 1
+#define CONFIG_SYS_FSL_NO_SERDES 1
+
+#include "t4qds.h"
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_CACHE_FLUSH
+
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE 0x2000
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 133333333
+#define CONFIG_FSL_TBCLK_EXTRA_DIV 100
+
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SPD_BUS_NUM 1
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS3 0x53
+#define SPD_EEPROM_ADDRESS4 0x54
+#define SPD_EEPROM_ADDRESS5 0x55
+#define SPD_EEPROM_ADDRESS6 0x56
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_32 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(0)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \
+ FTIM0_NOR_TEADC(0x1) | \
+ FTIM0_NOR_TEAHC(0x1))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \
+ FTIM1_NOR_TRAD_NOR(0x1))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x0) | \
+ FTIM2_NOR_TCH(0x0) | \
+ FTIM2_NOR_TWP(0x1))
+#define CONFIG_SYS_NOR_FTIM3 0x04000000
+#define CONFIG_SYS_IFC_CCR 0x01000000
+
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+
+/* I2C */
+#define CONFIG_SYS_I2C_SPEED 4000000 /* faster speed for emulator */
+
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 50
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 50
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_INTERLAKEN
+
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+
+
+
+#define CONFIG_BOOTDELAY 0
+
+/*
+ * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
+ * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
+ * interleaving. It can be cacheline, page, bank, superbank.
+ * See doc/README.fsl-ddr for details.
+ */
+#ifdef CONFIG_PPC_T4240
+#define CTRL_INTLV_PREFERED 3way_4KB
+#else
+#define CTRL_INTLV_PREFERED cacheline
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
+ "bank_intlv=auto;" \
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=t4240emu/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=t4240emu/t4240emu.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the proof point
+ * app code automatically
+ */
+#define CONFIG_PROOF_POINTS \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x29000000 - - -;" \
+ "cpu 2 release 0x29000000 - - -;" \
+ "cpu 3 release 0x29000000 - - -;" \
+ "cpu 4 release 0x29000000 - - -;" \
+ "cpu 5 release 0x29000000 - - -;" \
+ "cpu 6 release 0x29000000 - - -;" \
+ "cpu 7 release 0x29000000 - - -;" \
+ "go 0x29000000"
+
+#define CONFIG_HVBOOT \
+ "setenv bootargs config-addr=0x60000000; " \
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_LINUX \
+ "errata;" \
+ "setenv othbootargs ignore_loglevel;" \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h
index 6dd5c0d..6294f2b 100644
--- a/include/configs/T4240QDS.h
+++ b/include/configs/T4240QDS.h
@@ -23,6 +23,9 @@
/*
* T4240 QDS board configuration file
*/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
#define CONFIG_T4240QDS
#define CONFIG_PHYS_64BIT
@@ -31,4 +34,540 @@
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
+#endif
+
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#define CONFIG_DDR_ECC
+
#include "t4qds.h"
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 1097)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS3 0x53
+#define SPD_EEPROM_ADDRESS4 0x54
+#define SPD_EEPROM_ADDRESS5 0x55
+#define SPD_EEPROM_ADDRESS6 0x56
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS /* use common QIXIS code */
+#define QIXIS_BASE 0xffdf0000
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x04
+#define QIXIS_RST_CTL_RESET 0x83
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
+
+#define CONFIG_SYS_CSPR3_EXT (0xf)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3 0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3 0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+
+/* I2C */
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */
+
+#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+#define I2C_MUX_CH_VSC3316_FS 0xc
+#define I2C_MUX_CH_VSC3316_BS 0xd
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR 0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+
+/* VSC Crossbar switches */
+#define CONFIG_VSC_CROSSBAR
+#define VSC3316_FSM_TX_ADDR 0x70
+#define VSC3316_FSM_RX_ADDR 0x71
+
+/*
+ * RapidIO
+ */
+
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 50
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 50
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored@0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_TERANETICS
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#define FM1_10GEC1_PHY_ADDR 0x0
+#define FM1_10GEC2_PHY_ADDR 0x1
+#define FM2_10GEC1_PHY_ADDR 0x2
+#define FM2_10GEC2_PHY_ADDR 0x3
+#endif
+
+
+/* SATA */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1 at DTSEC1"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+
+#define __USB_PHY_TYPE utmi
+
+/*
+ * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
+ * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
+ * interleaving. It can be cacheline, page, bank, superbank.
+ * See doc/README.fsl-ddr for details.
+ */
+#ifdef CONFIG_PPC_T4240
+#define CTRL_INTLV_PREFERED 3way_4KB
+#else
+#define CTRL_INTLV_PREFERED cacheline
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
+ "bank_intlv=auto;" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=t4240qds/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=t4240qds/t4240qds.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+#define CONFIG_HVBOOT \
+ "setenv bootargs config-addr=0x60000000; " \
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x01000000 - - -;" \
+ "cpu 2 release 0x01000000 - - -;" \
+ "cpu 3 release 0x01000000 - - -;" \
+ "cpu 4 release 0x01000000 - - -;" \
+ "cpu 5 release 0x01000000 - - -;" \
+ "cpu 6 release 0x01000000 - - -;" \
+ "cpu 7 release 0x01000000 - - -;" \
+ "go 0x01000000"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h
index 3f7b82d..c3fa3b7 100644
--- a/include/configs/t4qds.h
+++ b/include/configs/t4qds.h
@@ -23,15 +23,8 @@
/*
* Corenet DS style board configuration file
*/
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
-#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
-#endif
+#ifndef __T4QDS_H
+#define __T4QDS_H
#define CONFIG_CMD_REGINFO
@@ -69,63 +62,12 @@
#define CONFIG_ENV_OVERWRITE
-#ifdef CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_NOWHERE
-#else
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#ifndef CONFIG_SYS_NO_FLASH
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 1097)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-#else /* CONFIG_SYS_NO_FLASH */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
@@ -149,13 +91,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
/*
* DDR Setup
*/
@@ -171,15 +106,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_DDR_SPD
#define CONFIG_FSL_DDR3
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS1 0x51
-#define SPD_EEPROM_ADDRESS2 0x52
-#define SPD_EEPROM_ADDRESS3 0x53
-#define SPD_EEPROM_ADDRESS4 0x54
-#define SPD_EEPROM_ADDRESS5 0x55
-#define SPD_EEPROM_ADDRESS6 0x56
-#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
-#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
/*
* IFC Definitions
@@ -187,171 +113,9 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_FLASH_BASE 0xe0000000
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
- + 0x8000000) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
- FTIM0_NOR_TEADC(0x5) | \
- FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
- FTIM1_NOR_TRAD_NOR(0x1A) |\
- FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
- FTIM2_NOR_TCH(0x4) | \
- FTIM2_NOR_TWPH(0x0E) | \
- FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3 0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
- + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-
-#define CONFIG_FSL_QIXIS /* use common QIXIS code */
-#define QIXIS_BASE 0xffdf0000
-#define QIXIS_LBMAP_SWITCH 6
-#define QIXIS_LBMAP_MASK 0x0f
-#define QIXIS_LBMAP_SHIFT 0
-#define QIXIS_LBMAP_DFLTBANK 0x00
-#define QIXIS_LBMAP_ALTBANK 0x04
-#define QIXIS_RST_CTL_RESET 0x83
-#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
-#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
-#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
-#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
-
-#define CONFIG_SYS_CSPR3_EXT (0xf)
-#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 \
- | CSPR_MSEL_GPCM \
- | CSPR_V)
-#define CONFIG_SYS_AMASK3 IFC_AMASK(4 * 1024)
-#define CONFIG_SYS_CSOR3 0x0
-/* QIXIS Timing parameters for IFC CS3 */
-#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
- FTIM0_GPCM_TEADC(0x0e) | \
- FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
- FTIM1_GPCM_TRAD(0x3f))
-#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
- FTIM2_GPCM_TCH(0x0) | \
- FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS3_FTIM3 0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
- | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#if defined(CONFIG_NAND)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
-#endif
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_MISC_INIT_R
@@ -412,28 +176,9 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_OFFSET 0x118000
#define CONFIG_SYS_I2C2_OFFSET 0x118100
-#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
-#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */
-
-#define I2C_MUX_CH_DEFAULT 0x8
-#define I2C_MUX_CH_VOL_MONITOR 0xa
-#define I2C_MUX_CH_VSC3316_FS 0xc
-#define I2C_MUX_CH_VSC3316_BS 0xd
-
-/* Voltage monitor on channel 2*/
-#define I2C_VOL_MONITOR_ADDR 0x40
-#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
-#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
-#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
-
-/* VSC Crossbar switches */
-#define CONFIG_VSC_CROSSBAR
-#define VSC3316_FSM_TX_ADDR 0x70
-#define VSC3316_FSM_RX_ADDR 0x71
/*
* RapidIO
@@ -447,44 +192,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
/*
- * for slave u-boot IMAGE instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
-/*
- * for slave UCODE and ENV instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
-
-/* slave core release by master*/
-#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
-#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
-
-/*
- * SRIO_PCIE_BOOT - SLAVE
- */
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
-#endif
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE 0
-
-/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
@@ -527,66 +234,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS 50
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_QMAN_NUM_PORTALS 50
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-#define CONFIG_SYS_PMAN
-#define CONFIG_SYS_DPAA_DCE
-#define CONFIG_SYS_INTERLAKEN
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 545KB (1089 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_TERANETICS
-#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
-#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
-#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
-#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
-#define FM1_10GEC1_PHY_ADDR 0x0
-#define FM1_10GEC2_PHY_ADDR 0x1
-#define FM2_10GEC1_PHY_ADDR 0x2
-#define FM2_10GEC2_PHY_ADDR 0x3
-#endif
-
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_NET_MULTI
@@ -649,30 +296,6 @@ unsigned long get_board_ddr_clk(void);
#endif
/*
-* USB
-*/
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
-#define CONFIG_HAS_FSL_DR_USB
-
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
@@ -713,112 +336,11 @@ unsigned long get_board_ddr_clk(void);
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
-#define __USB_PHY_TYPE utmi
-
-/*
- * T4240 has 3 DDR controllers. Default to 3way_4KB interleaving. It can be
- * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to
- * cacheline interleaving. It can be cacheline, page, bank, superbank.
- * See doc/README.fsl-ddr for details.
- */
-#ifdef CONFIG_PPC_T4240
-#define CTRL_INTLV_PREFERED 3way_4KB
-#else
-#define CTRL_INTLV_PREFERED cacheline
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:" \
- "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
- "bank_intlv=auto;" \
- "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
- "netdev=eth0\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot && " \
- "protect off $ubootaddr +$filesize && " \
- "erase $ubootaddr +$filesize && " \
- "cp.b $loadaddr $ubootaddr $filesize && " \
- "protect on $ubootaddr +$filesize && " \
- "cmp.b $loadaddr $ubootaddr $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=t4240qds/ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=t4240qds/t4240qds.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
-
-/* For emulation this causes u-boot to jump to the start of the proof point
- app code automatically */
-#define CONFIG_PROOF_POINTS \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "cpu 1 release 0x29000000 - - -;" \
- "cpu 2 release 0x29000000 - - -;" \
- "cpu 3 release 0x29000000 - - -;" \
- "cpu 4 release 0x29000000 - - -;" \
- "cpu 5 release 0x29000000 - - -;" \
- "cpu 6 release 0x29000000 - - -;" \
- "cpu 7 release 0x29000000 - - -;" \
- "go 0x29000000"
-
#define CONFIG_HVBOOT \
"setenv bootargs config-addr=0x60000000; " \
"bootm 0x01000000 - 0x00f00000"
-#define CONFIG_ALU \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "cpu 1 release 0x01000000 - - -;" \
- "cpu 2 release 0x01000000 - - -;" \
- "cpu 3 release 0x01000000 - - -;" \
- "cpu 4 release 0x01000000 - - -;" \
- "cpu 5 release 0x01000000 - - -;" \
- "cpu 6 release 0x01000000 - - -;" \
- "cpu 7 release 0x01000000 - - -;" \
- "go 0x01000000"
-
-#define CONFIG_LINUX \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
-#endif
-
#endif /* __CONFIG_H */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 14+ messages in thread