From: Darwin Rambo <drambo@broadcom.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 5/6] mmc: kona: Add Kona mmc driver
Date: Mon, 27 Jan 2014 10:53:29 -0800 [thread overview]
Message-ID: <1390848810-7227-6-git-send-email-drambo@broadcom.com> (raw)
In-Reply-To: <1390848810-7227-1-git-send-email-drambo@broadcom.com>
Add support for the Kona SDHCI found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
---
drivers/mmc/Makefile | 1 +
drivers/mmc/kona_sdhci.c | 127 ++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 128 insertions(+)
create mode 100644 drivers/mmc/kona_sdhci.c
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index e793ed9..931922b 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_OMAP_HSMMC) += omap_hsmmc.o
obj-$(CONFIG_PXA_MMC_GENERIC) += pxa_mmc_gen.o
obj-$(CONFIG_SDHCI) += sdhci.o
obj-$(CONFIG_BCM2835_SDHCI) += bcm2835_sdhci.o
+obj-$(CONFIG_KONA_SDHCI) += kona_sdhci.o
obj-$(CONFIG_S5P_SDHCI) += s5p_sdhci.o
obj-$(CONFIG_SH_MMCIF) += sh_mmcif.o
obj-$(CONFIG_SPEAR_SDHCI) += spear_sdhci.o
diff --git a/drivers/mmc/kona_sdhci.c b/drivers/mmc/kona_sdhci.c
new file mode 100644
index 0000000..c38e18e
--- /dev/null
+++ b/drivers/mmc/kona_sdhci.c
@@ -0,0 +1,127 @@
+/*****************************************************************************
+*
+* Copyright 2013 Broadcom Corporation. All rights reserved.
+*
+* SPDX-License-Identifier: GPL-2.0+
+*
+*****************************************************************************/
+
+#include <common.h>
+#include <malloc.h>
+#include <sdhci.h>
+#include <asm/errno.h>
+#include <asm/kona-common/clk.h>
+
+#define SDHCI_CORECTRL_OFFSET 0x00008000
+#define SDHCI_CORECTRL_EN 0x01
+#define SDHCI_CORECTRL_RESET 0x02
+
+#define SDHCI_CORESTAT_OFFSET 0x00008004
+#define SDHCI_CORESTAT_CD_SW 0x01
+
+#define SDHCI_COREIMR_OFFSET 0x00008008
+#define SDHCI_COREIMR_IP 0x01
+
+static int init_mmc_core(struct sdhci_host *host)
+{
+ unsigned int mask;
+ unsigned int timeout;
+
+ if (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & SDHCI_RESET_ALL) {
+ printf("%s: sd host controller reset error\n", __func__);
+ return 1;
+ }
+
+ /* For kona a hardware reset before anything else. */
+ mask = sdhci_readl(host, SDHCI_CORECTRL_OFFSET) | SDHCI_CORECTRL_RESET;
+ sdhci_writel(host, mask, SDHCI_CORECTRL_OFFSET);
+
+ /* Wait max 100 ms */
+ timeout = 1000;
+ do {
+ if (timeout == 0) {
+ printf("%s: reset timeout error\n", __func__);
+ return 1;
+ }
+ timeout--;
+ udelay(100);
+ } while (0 ==
+ (sdhci_readl(host, SDHCI_CORECTRL_OFFSET) &
+ SDHCI_CORECTRL_RESET));
+
+ /* Clear the reset bit. */
+ mask = mask & ~SDHCI_CORECTRL_RESET;
+ sdhci_writel(host, mask, SDHCI_CORECTRL_OFFSET);
+ udelay(10);
+
+ /* Enable AHB clock */
+ mask = sdhci_readl(host, SDHCI_CORECTRL_OFFSET);
+ sdhci_writel(host, mask | SDHCI_CORECTRL_EN, SDHCI_CORECTRL_OFFSET);
+
+ /* Enable interrupts */
+ sdhci_writel(host, SDHCI_COREIMR_IP, SDHCI_COREIMR_OFFSET);
+
+ /* Make sure Card is detected in controller */
+ mask = sdhci_readl(host, SDHCI_CORESTAT_OFFSET);
+ sdhci_writel(host, mask | SDHCI_CORESTAT_CD_SW, SDHCI_CORESTAT_OFFSET);
+
+ return 0;
+}
+
+int kona_sdhci_init(int dev_index, u32 min_clk, u32 quirks)
+{
+ int ret = 0;
+ u32 max_clk;
+ void *reg_base;
+ struct sdhci_host *host = NULL;
+
+ host = (struct sdhci_host *)malloc(sizeof(struct sdhci_host));
+ if (!host) {
+ printf("%s: sdhci host malloc fail!\n", __func__);
+ return -ENOMEM;
+ }
+ switch (dev_index) {
+ case 0:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE0;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO0_MAX_CLK,
+ &max_clk);
+ break;
+ case 1:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE1;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO1_MAX_CLK,
+ &max_clk);
+ break;
+ case 2:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE2;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO2_MAX_CLK,
+ &max_clk);
+ break;
+ case 3:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE3;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO3_MAX_CLK,
+ &max_clk);
+ break;
+ default:
+ printf("%s: sdio dev index %d not supported\n",
+ __func__, dev_index);
+ ret = -EINVAL;
+ }
+ if (ret)
+ return ret;
+
+ host->name = "kona-sdhci";
+ host->ioaddr = reg_base;
+ host->quirks = quirks;
+ host->host_caps = MMC_MODE_HC;
+
+ if (init_mmc_core(host))
+ return -EINVAL;
+
+ if (quirks & SDHCI_QUIRK_REG32_RW)
+ host->version = sdhci_readl(host, SDHCI_HOST_VERSION - 2) >> 16;
+ else
+ host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
+
+ add_sdhci(host, max_clk, min_clk);
+ return ret;
+}
--
1.7.9.5
next prev parent reply other threads:[~2014-01-27 18:53 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-27 18:53 [U-Boot] [PATCH 0/6] Introducing the Broadcom bcm281xx Architecture Darwin Rambo
2014-01-27 18:53 ` [U-Boot] [PATCH 1/6] arch: kona: Initial commit of kona-common architecture code Darwin Rambo
2014-01-29 22:32 ` Tom Rini
2014-01-30 23:09 ` Darwin Rambo
2014-01-27 18:53 ` [U-Boot] [PATCH 2/6] arch: bcm281xx: Initial commit of bcm281xx " Darwin Rambo
2014-01-29 22:32 ` Tom Rini
2014-01-30 22:03 ` Darwin Rambo
2014-01-31 17:54 ` Tom Rini
2014-01-31 18:19 ` Darwin Rambo
2014-01-31 17:47 ` Matt Porter
2014-01-27 18:53 ` [U-Boot] [PATCH 3/6] gpio: kona: Add Kona gpio driver Darwin Rambo
2014-01-27 18:53 ` [U-Boot] [PATCH 4/6] i2c: kona: Add Kona I2C driver Darwin Rambo
2014-01-27 18:53 ` Darwin Rambo [this message]
2014-01-27 18:53 ` [U-Boot] [PATCH 6/6] board: bcm28155_ap: Add board files Darwin Rambo
2014-01-29 22:33 ` Tom Rini
2014-01-30 23:05 ` Darwin Rambo
2014-01-31 14:17 ` Tom Rini
2014-01-31 17:05 ` Tim Kryger
2014-01-31 17:15 ` Tom Rini
2014-01-31 18:18 ` Darwin Rambo
2014-01-29 22:32 ` [U-Boot] [PATCH 0/6] Introducing the Broadcom bcm281xx Architecture Tom Rini
2014-01-30 23:12 ` Darwin Rambo
2014-01-31 19:14 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1390848810-7227-6-git-send-email-drambo@broadcom.com \
--to=drambo@broadcom.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox