From: Simon Glass <sjg@chromium.org>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 08/11] dm: net: Tidy up designware driver ready for driver model
Date: Sun, 5 Apr 2015 16:07:40 -0600 [thread overview]
Message-ID: <1428271663-3814-9-git-send-email-sjg@chromium.org> (raw)
In-Reply-To: <1428271663-3814-1-git-send-email-sjg@chromium.org>
Adjust the error handling to use errno.h instead of returning -1. Change
leaf functions to pass in the arguments they require rather than struct
eth_device. Apart from simplifying the code it makes is easier to reuse
these functions for driver model, since mostly they actually only use
struct dw_eth_priv (which we can keep).
Create a stub for each Ethernet operation function. This will allow use to
share code with the driver model versions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
---
Changes in v2: None
drivers/net/designware.c | 87 +++++++++++++++++++++++++++++-------------------
1 file changed, 53 insertions(+), 34 deletions(-)
diff --git a/drivers/net/designware.c b/drivers/net/designware.c
index cc01604..5b36d4f 100644
--- a/drivers/net/designware.c
+++ b/drivers/net/designware.c
@@ -6,10 +6,11 @@
*/
/*
- * Designware ethernet IP driver for u-boot
+ * Designware ethernet IP driver for U-Boot
*/
#include <common.h>
+#include <errno.h>
#include <miiphy.h>
#include <malloc.h>
#include <linux/compiler.h>
@@ -40,7 +41,7 @@ static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
udelay(10);
};
- return -1;
+ return -ETIMEDOUT;
}
static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
@@ -49,7 +50,7 @@ static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
struct eth_mac_regs *mac_p = bus->priv;
ulong start;
u16 miiaddr;
- int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
+ int ret = -ETIMEDOUT, timeout = CONFIG_MDIO_TIMEOUT;
writel(val, &mac_p->miidata);
miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
@@ -69,27 +70,26 @@ static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
return ret;
}
-static int dw_mdio_init(char *name, struct eth_mac_regs *mac_regs_p)
+static int dw_mdio_init(const char *name, struct eth_mac_regs *mac_regs_p)
{
struct mii_dev *bus = mdio_alloc();
if (!bus) {
printf("Failed to allocate MDIO bus\n");
- return -1;
+ return -ENOMEM;
}
bus->read = dw_mdio_read;
bus->write = dw_mdio_write;
- sprintf(bus->name, name);
+ snprintf(bus->name, sizeof(bus->name), name);
bus->priv = (void *)mac_regs_p;
return mdio_register(bus);
}
-static void tx_descs_init(struct eth_device *dev)
+static void tx_descs_init(struct dw_eth_dev *priv)
{
- struct dw_eth_dev *priv = dev->priv;
struct eth_dma_regs *dma_p = priv->dma_regs_p;
struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0];
char *txbuffs = &priv->txbuffs[0];
@@ -128,9 +128,8 @@ static void tx_descs_init(struct eth_device *dev)
priv->tx_currdescnum = 0;
}
-static void rx_descs_init(struct eth_device *dev)
+static void rx_descs_init(struct dw_eth_dev *priv)
{
- struct dw_eth_dev *priv = dev->priv;
struct eth_dma_regs *dma_p = priv->dma_regs_p;
struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0];
char *rxbuffs = &priv->rxbuffs[0];
@@ -170,12 +169,10 @@ static void rx_descs_init(struct eth_device *dev)
priv->rx_currdescnum = 0;
}
-static int dw_write_hwaddr(struct eth_device *dev)
+static int _dw_write_hwaddr(struct dw_eth_dev *priv, u8 *mac_id)
{
- struct dw_eth_dev *priv = dev->priv;
struct eth_mac_regs *mac_p = priv->mac_regs_p;
u32 macid_lo, macid_hi;
- u8 *mac_id = &dev->enetaddr[0];
macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) +
(mac_id[3] << 24);
@@ -213,9 +210,8 @@ static void dw_adjust_link(struct eth_mac_regs *mac_p,
(phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
}
-static void dw_eth_halt(struct eth_device *dev)
+static void _dw_eth_halt(struct dw_eth_dev *priv)
{
- struct dw_eth_dev *priv = dev->priv;
struct eth_mac_regs *mac_p = priv->mac_regs_p;
struct eth_dma_regs *dma_p = priv->dma_regs_p;
@@ -225,12 +221,12 @@ static void dw_eth_halt(struct eth_device *dev)
phy_shutdown(priv->phydev);
}
-static int dw_eth_init(struct eth_device *dev, bd_t *bis)
+static int _dw_eth_init(struct dw_eth_dev *priv, u8 *enetaddr)
{
- struct dw_eth_dev *priv = dev->priv;
struct eth_mac_regs *mac_p = priv->mac_regs_p;
struct eth_dma_regs *dma_p = priv->dma_regs_p;
unsigned int start;
+ int ret;
writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
@@ -238,7 +234,7 @@ static int dw_eth_init(struct eth_device *dev, bd_t *bis)
while (readl(&dma_p->busmode) & DMAMAC_SRST) {
if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT) {
printf("DMA reset timeout\n");
- return -1;
+ return -ETIMEDOUT;
}
mdelay(100);
@@ -246,10 +242,10 @@ static int dw_eth_init(struct eth_device *dev, bd_t *bis)
/* Soft reset above clears HW address registers.
* So we have to set it here once again */
- dw_write_hwaddr(dev);
+ _dw_write_hwaddr(priv, enetaddr);
- rx_descs_init(dev);
- tx_descs_init(dev);
+ rx_descs_init(priv);
+ tx_descs_init(priv);
writel(FIXEDBURST | PRIORXTX_41 | DMA_PBL, &dma_p->busmode);
@@ -268,25 +264,25 @@ static int dw_eth_init(struct eth_device *dev, bd_t *bis)
#endif
/* Start up the PHY */
- if (phy_startup(priv->phydev)) {
+ ret = phy_startup(priv->phydev);
+ if (ret) {
printf("Could not initialize PHY %s\n",
priv->phydev->dev->name);
- return -1;
+ return ret;
}
dw_adjust_link(mac_p, priv->phydev);
if (!priv->phydev->link)
- return -1;
+ return -EIO;
writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf);
return 0;
}
-static int dw_eth_send(struct eth_device *dev, void *packet, int length)
+static int _dw_eth_send(struct dw_eth_dev *priv, void *packet, int length)
{
- struct dw_eth_dev *priv = dev->priv;
struct eth_dma_regs *dma_p = priv->dma_regs_p;
u32 desc_num = priv->tx_currdescnum;
struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num];
@@ -309,7 +305,7 @@ static int dw_eth_send(struct eth_device *dev, void *packet, int length)
/* Check if the descriptor is owned by CPU */
if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) {
printf("CPU not owner of tx frame\n");
- return -1;
+ return -EPERM;
}
memcpy(desc_p->dmamac_addr, packet, length);
@@ -347,9 +343,8 @@ static int dw_eth_send(struct eth_device *dev, void *packet, int length)
return 0;
}
-static int dw_eth_recv(struct eth_device *dev)
+static int _dw_eth_recv(struct dw_eth_dev *priv)
{
- struct dw_eth_dev *priv = dev->priv;
u32 status, desc_num = priv->rx_currdescnum;
struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num];
int length = 0;
@@ -395,9 +390,8 @@ static int dw_eth_recv(struct eth_device *dev)
return length;
}
-static int dw_phy_init(struct eth_device *dev)
+static int dw_phy_init(struct dw_eth_dev *priv, void *dev)
{
- struct dw_eth_dev *priv = dev->priv;
struct phy_device *phydev;
int mask = 0xffffffff;
@@ -407,7 +401,7 @@ static int dw_phy_init(struct eth_device *dev)
phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
if (!phydev)
- return -1;
+ return -ENODEV;
phy_connect_dev(phydev, dev);
@@ -417,7 +411,32 @@ static int dw_phy_init(struct eth_device *dev)
priv->phydev = phydev;
phy_config(phydev);
- return 1;
+ return 0;
+}
+
+static int dw_eth_init(struct eth_device *dev, bd_t *bis)
+{
+ return _dw_eth_init(dev->priv, dev->enetaddr);
+}
+
+static int dw_eth_send(struct eth_device *dev, void *packet, int length)
+{
+ return _dw_eth_send(dev->priv, packet, length);
+}
+
+static int dw_eth_recv(struct eth_device *dev)
+{
+ return _dw_eth_recv(dev->priv);
+}
+
+static void dw_eth_halt(struct eth_device *dev)
+{
+ return _dw_eth_halt(dev->priv);
+}
+
+static int dw_write_hwaddr(struct eth_device *dev)
+{
+ return _dw_write_hwaddr(dev->priv, dev->enetaddr);
}
int designware_initialize(ulong base_addr, u32 interface)
@@ -465,5 +484,5 @@ int designware_initialize(ulong base_addr, u32 interface)
dw_mdio_init(dev->name, priv->mac_regs_p);
priv->bus = miiphy_get_dev_by_name(dev->name);
- return dw_phy_init(dev);
+ return dw_phy_init(priv, dev);
}
--
2.2.0.rc0.207.ga3a616c
next prev parent reply other threads:[~2015-04-05 22:07 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-05 22:07 [U-Boot] [PATCH v2 0/11] dm: net: Conversion patches for sunxi driver model Ethernet Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 01/11] sunxi: Replace the pcDuino3 config with FDT version Simon Glass
2015-04-09 3:00 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 02/11] Kconfig: Move CONFIG_DESIGNWARE_ETH to Kconfig Simon Glass
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 03/11] dts: sunxi: Bring in Ethernet device tree bindings Simon Glass
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 04/11] dm: core: Support allocating driver-private data for DMA Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 05/11] dm: net: Use existing Ethernet init for driver model Simon Glass
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 06/11] Avoid calling print_eths() with " Simon Glass
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 07/11] dm: net: Adjust PHY interface to work with CONFIG_DM_ETH Simon Glass
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` Simon Glass [this message]
2015-04-09 3:04 ` [U-Boot] [PATCH v2 08/11] dm: net: Tidy up designware driver ready for driver model Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 09/11] dm: net: Adjust designware driver to support " Simon Glass
2015-04-06 21:09 ` Joe Hershberger
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 10/11] dm: sunxi: Support driver model for Ethernet Simon Glass
2015-04-09 3:04 ` Simon Glass
2015-04-05 22:07 ` [U-Boot] [PATCH v2 11/11] dm: sunxi: Use driver model for Ethernet on Linksprite pcDuino3 Simon Glass
2015-04-09 3:04 ` Simon Glass
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1428271663-3814-9-git-send-email-sjg@chromium.org \
--to=sjg@chromium.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox