[U-Boot] [PATCH 17/21] sunxi: dts: Add dts files which have been submitted but not yet merged upstream

Hans de Goede
2015-04-24T13:48:26Z

We need dts files for all boards we support, so bring in a few unmerged ones,
these will be replaced with the upstream merged versions the next time we
sync dts files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
arch/arm/dts/Makefile | 2 +
arch/arm/dts/sun4i-a10-jesurun-q5.dts | 194 ++++++++++++++++++++++++++++++++++
arch/arm/dts/sun7i-a20-primo73.dts | 102 ++++++++++++++++++
3 files changed, 298 insertions(+)
create mode 100644 arch/arm/dts/sun4i-a10-jesurun-q5.dts
create mode 100644 arch/arm/dts/sun7i-a20-primo73.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 3ff55dd..a18c565 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -65,6 +65,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-hackberry.dtb \
sun4i-a10-hyundai-a7hd.dtb \
sun4i-a10-inet97fv2.dtb \
+ sun4i-a10-jesurun-q5.dtb \
sun4i-a10-marsboard.dtb \
sun4i-a10-mini-xplus.dtb \
sun4i-a10-mk802.dtb \
@@ -102,6 +103,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-orangepi-mini.dtb \
sun7i-a20-pcduino3.dtb \
sun7i-a20-pcduino3-nano.dtb \
+ sun7i-a20-primo73.dtb \
sun7i-a20-wexler-tab7200.dtb
dtb-$(CONFIG_MACH_SUN8I_A23) += \
sun8i-a23-ippo-q8h-v5.dtb \
diff --git a/arch/arm/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/dts/sun4i-a10-jesurun-q5.dts
new file mode 100644
index 0000000..1b0452f
--- /dev/null
+++ b/arch/arm/dts/sun4i-a10-jesurun-q5.dts
@@ -0,0 +1,194 @@
+/*
+ * Copyright 2015 G?bor Nyers
+ *
+ * G?bor Nyers <gabor.nyers@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Jesurun Q5";
+ compatible = "jesurun,q5", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_q5>;
+
+ green {
+ label = "q5:green:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+ };
+
+ };
+
+ reg_emac_3v3: emac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_power_pin_q5>;
+ regulator-name = "emac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ phy-supply = <&reg_emac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ emac_power_pin_q5: emac_power_pin at 0 {
+ allwinner,pins = "PH19";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_q5: led_pins at 0 {
+ allwinner,pins = "PH20";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&reg_usb1_vbus {
+ status = "okay";
+};
+
+&reg_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ usb2_vbus-supply = <&reg_usb2_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun7i-a20-primo73.dts b/arch/arm/dts/sun7i-a20-primo73.dts
new file mode 100644
index 0000000..0658f82
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-primo73.dts
@@ -0,0 +1,102 @@
+/*
+ * Copyright 2014 Siarhei Siamashka <siarhei.siamashka@xxxxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+ model = "MSI Primo73 tablet";
+ compatible = "msi,primo73", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ soc at 01c00000 {
+ mmc0: mmc at 01c0f000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 0>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+ };
+
+ usbphy: phy at 01c13400 {
+ usb2_vbus-supply = <&reg_usb2_vbus>;
+ status = "okay";
+ };
+
+ ehci1: usb at 01c1c000 {
+ /* rtl8188etv wifi is connected here */
+ status = "okay";
+ };
+
+ pinctrl at 01c20800 {
+ usb2_vbus_pin_a: usb2_vbus_pin at 0 {
+ allwinner,pins = "PH12";
+ };
+ };
+
+ uart0: serial at 01c28000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+ };
+ };
+
+ reg_usb2_vbus: usb2-vbus {
+ gpio = <&pio 7 12 0>; /* PH12 */
+ status = "okay";
+ };
+};
--
2.3.5