[U-Boot] [PATCH] hummingboard: Remove unused directory

public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed

From: Fabio Estevam <festevam@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] hummingboard: Remove unused directory
Date: Fri, 15 May 2015 16:10:47 -0300	[thread overview]
Message-ID: <1431717047-4900-1-git-send-email-festevam@gmail.com> (raw)

From: Fabio Estevam <fabio.estevam@freescale.com>

The 'mx6-microsom' directory was only used for the previous mx6solo
hummingboard support, which has been removed in favour of the SPL
version.

Remove the remaining piece of the old mx6solo hummingboard support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 board/solidrun/mx6-microsom/800mhz_2x128mx16.cfg   | 74 ---------------------
 board/solidrun/mx6-microsom/clocks.cfg             | 33 ----------
 .../mx6-microsom/ddr-800mhz-32bit-setup.cfg        | 76 ----------------------
 3 files changed, 183 deletions(-)
 delete mode 100644 board/solidrun/mx6-microsom/800mhz_2x128mx16.cfg
 delete mode 100644 board/solidrun/mx6-microsom/clocks.cfg
 delete mode 100644 board/solidrun/mx6-microsom/ddr-800mhz-32bit-setup.cfg

diff --git a/board/solidrun/mx6-microsom/800mhz_2x128mx16.cfg b/board/solidrun/mx6-microsom/800mhz_2x128mx16.cfg
deleted file mode 100644
index 40747ab..0000000
--- a/board/solidrun/mx6-microsom/800mhz_2x128mx16.cfg
+++ /dev/null
@@ -1,74 +0,0 @@
-/*
- * Copyright (C) 2013 Boundary Devices
- * Copyright (C) 2013 SolidRun ltd.
- * Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* ZQ Calibrations */
-DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003
-DATA 4, MX6_MMDC_P1_MPZQHWCTRL, 0xa1390003
-/* write leveling */
-DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x005a0057
-DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x004a0052
-/*
- * DQS gating, read delay, write delay calibration values
- * based on calibration compare of 0x00ffff00
- */
-DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x02480240
-DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x02340230
-DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x40404440
-DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x38343034
-/* read data bit delay */
-DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
-/* Complete calibration by forced measurement */
-DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
-DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800
-
-/*
- * MMDC init:
- * in DDR3, 32-bit mode, only MMDC0 is initiated:
- */
-DATA 4, MX6_MMDC_P0_MDPDC, 0x0002002d
-DATA 4, MX6_MMDC_P0_MDOTC, 0x00333040
-
-DATA 4, MX6_MMDC_P0_MDCFG0, 0x3f435313
-DATA 4, MX6_MMDC_P0_MDCFG1, 0xb66e8b63
-
-DATA 4, MX6_MMDC_P0_MDCFG2, 0x01ff00db
-DATA 4, MX6_MMDC_P0_MDMISC, 0x00011740
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
-DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2
-DATA 4, MX6_MMDC_P0_MDOR, 0x00431023
-/* CS0_END - 0x2fffffff, 512M  */
-DATA 4, MX6_MMDC_P0_MDASP, 0x00000017
-
-/* MMDC0_MAARCR ADOPT optimized priorities. Dyn jump disabled */
-DATA 4, 0x021b0400, 0x11420000
-
-/* MMDC0_MDCTL- row-14bits; col-10bits; burst length 8;32-bit data bus */
-DATA 4, MX6_MMDC_P0_MDCTL, 0x83190000
-
-/*
- * Initialize 2GB DDR3 - Hynix H5TQ2G63BFR-H9C
- * MR2
- */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008032
-/* MR3 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
-/* MR1 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008031
-/* MR0 */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x05208030
-/* ZQ calibration */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
-/* final DDR setup */
-DATA 4, MX6_MMDC_P0_MDREF, 0x00007800
-DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000007
-DATA 4, MX6_MMDC_P0_MDPDC, 0x0002556d
-DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
diff --git a/board/solidrun/mx6-microsom/clocks.cfg b/board/solidrun/mx6-microsom/clocks.cfg
deleted file mode 100644
index 1288811..0000000
--- a/board/solidrun/mx6-microsom/clocks.cfg
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * Copyright (C) 2013 Boundary Devices
- * Copyright (C) 2013 SolidRun ltd.
- * Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* set the default clock gate to save power */
-DATA 4, CCM_CCGR0, 0x00C03F3F
-DATA 4, CCM_CCGR1, 0x0030FC03
-DATA 4, CCM_CCGR2, 0x0FFFC000
-DATA 4, CCM_CCGR3, 0x3FF00000
-DATA 4, CCM_CCGR4, 0x00FFF300
-DATA 4, CCM_CCGR5, 0x0F0000C3
-DATA 4, CCM_CCGR6, 0x000003FF
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
-/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
-DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
-DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
-
-/*
- * Setup CCM_CCOSR register as follows:
- *
- * cko1_en  = 1    --> CKO1 enabled
- * cko1_div = 111  --> divide by 8
- * cko1_sel = 1011 --> ahb_clk_root
- *
- * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz
- */
-DATA 4, CCM_CCOSR, 0x000000fb
diff --git a/board/solidrun/mx6-microsom/ddr-800mhz-32bit-setup.cfg b/board/solidrun/mx6-microsom/ddr-800mhz-32bit-setup.cfg
deleted file mode 100644
index f92fc19..0000000
--- a/board/solidrun/mx6-microsom/ddr-800mhz-32bit-setup.cfg
+++ /dev/null
@@ -1,76 +0,0 @@
-/*
- * Copyright (C) 2013 Boundary Devices
- * Copyright (C) 2013 SolidRun ltd.
- * Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * DDR3 settings
- * MX6Q    ddr is limited to 1066 Mhz	currently 1056 MHz(528 MHz clock),
- *	   memory bus width: 64 bits	x16/x32/x64
- * MX6DL   ddr is limited to 800 MHz(400 MHz clock)
- *	   memory bus width: 64 bits	x16/x32/x64
- * MX6SOLO ddr is limited to 800 MHz(400 MHz clock)
- *	   memory bus width: 32 bits	x16/x32
- */
-/* DDR IO TYPE */
-DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000c0000
-DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
-/* Clock */
-DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000028
-DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000028
-/* Address */
-DATA 4, MX6_IOM_DRAM_CAS, 0x00000010
-DATA 4, MX6_IOM_DRAM_RAS, 0x00000010
-DATA 4, MX6_IOM_GRP_ADDDS, 0x00000010
-/* Control */
-DATA 4, MX6_IOM_DRAM_RESET, 0x00000010
-DATA 4, MX6_IOM_DRAM_SDCKE0, 0x00003000
-DATA 4, MX6_IOM_DRAM_SDCKE1, 0x00003000
-DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDODT0, 0x00000010
-DATA 4, MX6_IOM_DRAM_SDODT1, 0x00000010
-DATA 4, MX6_IOM_GRP_CTLDS, 0x00000010
-
-/*
- * Data Strobe: IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL - DDR_INPUT=0, CMOS,
- * CMOS mode saves power, but have less timing margin in case of DDR
- * timing issue on your board you can try DDR_MODE:  [= 0x00020000]
- */
-DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
-
-DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000028
-DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000028
-DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000028
-DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000028
-DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000000
-
-/*
- * DATA:IOMUXC_SW_PAD_CTL_GRP_DDRMODE - DDR_INPUT=0, CMOS,
- * CMOS mode saves power, but have less timing margin in case of DDR
- * timing issue on your board you can try DDR_MODE:  [= 0x00020000]
- */
-DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
-
-DATA 4, MX6_IOM_GRP_B0DS, 0x00000028
-DATA 4, MX6_IOM_GRP_B1DS, 0x00000028
-DATA 4, MX6_IOM_GRP_B2DS, 0x00000028
-DATA 4, MX6_IOM_GRP_B3DS, 0x00000028
-DATA 4, MX6_IOM_GRP_B4DS, 0x00000000
-DATA 4, MX6_IOM_GRP_B5DS, 0x00000000
-DATA 4, MX6_IOM_GRP_B6DS, 0x00000000
-DATA 4, MX6_IOM_GRP_B7DS, 0x00000000
-
-DATA 4, MX6_IOM_DRAM_DQM0, 0x00000028
-DATA 4, MX6_IOM_DRAM_DQM1, 0x00000028
-DATA 4, MX6_IOM_DRAM_DQM2, 0x00000028
-DATA 4, MX6_IOM_DRAM_DQM3, 0x00000028
-DATA 4, MX6_IOM_DRAM_DQM4, 0x00000000
-DATA 4, MX6_IOM_DRAM_DQM5, 0x00000000
-DATA 4, MX6_IOM_DRAM_DQM6, 0x00000000
-DATA 4, MX6_IOM_DRAM_DQM7, 0x00000000
-- 
1.9.1

next             reply	other threads:[~2015-05-15 19:10 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-05-15 19:10 Fabio Estevam [this message]
2015-05-15 19:42 ` [U-Boot] [PATCH] hummingboard: Remove unused directory Stefano Babic
2015-05-19 13:09 ` Stefano Babic

find likely ancestor, descendant, or conflicting patches for this message:
( dfblob:40747ab dfblob:1288811 dfblob:f92fc19 )
 OR (
bs:"[U-Boot] [PATCH] hummingboard: Remove unused directory" )
	(help)

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1431717047-4900-1-git-send-email-festevam@gmail.com \
    --to=festevam@gmail.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Be sure your reply has a Subject: header at the top and a blank line before the message body.

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox