[U-Boot] [PATCH] thermal: imx_thermal: increase critical temperature threshold

[Liu Jason <Hui.Liu@freescale.com>]

________________________________________
From: Tim Harvey <tharvey@gateworks.com>
Sent: Thursday, May 21, 2015 11:40 PM
To: Stefano Babic
Cc: u-boot at lists.denx.de; Stefan Roese; Eric Nelson; Heiko Schocher; Nikita Kiryanov; Jon Nettleton; Liu Hui-R64343; Li Ye-B37916; Estevam Fabio-R49496; Christian Gmeiner; Markus Niebel; Fan Peng-B51431
Subject: [U-Boot] [PATCH] thermal: imx_thermal: increase critical temperature threshold

The CPU temperature grade from OTP is now used to define the critical
threshold at which point we busyloop until we are below, however this
threshold is still too low.

Instead of 20C below the max CPU temperature, change it to 5C defined now
by TEMPERATURE_HOT_DETLA for clarity. Rename 'passive' to 'critical'
as that better defines our use case here. Additionally change the output
of the busyloop message to show the max CPU temperature as well as current.

Before:
CPU Temperature is 101 C, too hot to boot, waiting...
CPU Temperature is 101 C, too hot to boot, waiting...

After:
CPU Temperature (101C) too close to max (105C) waiting...
CPU Temperature (101C) too close to max (105C) waiting...

Cc: Stefan Roese <sr@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Ye Li <b37916@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Peng Fan <b51431@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
 drivers/thermal/imx_thermal.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)


Looks good to me, thus:

Acked-by: Jason Liu <r64343@freescale.com> 

Jason Liu

diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index b5dab63..0d893c9 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c
@@ -19,6 +19,8 @@
 #include <thermal.h>
 #include <imx_thermal.h>

+/* board will busyloop until this many degrees C below CPU max temperature */
+#define TEMPERATURE_HOT_DELTA   5 /* CPU maxT - 5C */
 #define FACTOR0                        10000000
 #define FACTOR1                        15976
 #define FACTOR2                        4297157
@@ -34,7 +36,7 @@

 struct thermal_data {
        unsigned int fuse;
-       int passive;
+       int critical;
        int minc;
        int maxc;
 };
@@ -129,9 +131,10 @@ int imx_thermal_get_temp(struct udevice *dev, int *temp)

        cpu_tmp = read_cpu_temperature(dev);
        while (cpu_tmp > priv->minc && cpu_tmp < priv->maxc) {
-               if (cpu_tmp >= priv->passive) {
-                       printf("CPU Temperature is %d C, too hot to boot, waiting...\n",
-                              cpu_tmp);
+               if (cpu_tmp >= priv->critical) {
+                       printf("CPU Temperature (%dC) too close to max (%dC)",
+                              cpu_tmp, priv->maxc);
+                       puts(" waiting...\n");
                        udelay(5000000);
                        cpu_tmp = read_cpu_temperature(dev);
                } else {
@@ -164,9 +167,9 @@ static int imx_thermal_probe(struct udevice *dev)
                return -EPERM;
        }

-       /* set passive cooling temp to max - 20C */
+       /* set critical cooling temp */
        get_cpu_temp_grade(&priv->minc, &priv->maxc);
-       priv->passive = priv->maxc - 20;
+       priv->critical = priv->maxc - TEMPERATURE_HOT_DELTA;
        priv->fuse = fuse;

        enable_thermal_clk();
--
1.9.1