[U-Boot] [PATCH] net/designware: revert MAC-address setup on init

[Alexey Brodkin <Alexey.Brodkin@synopsys.com>]

Hi Joe,

On Wed, 2015-07-01 at 18:02 -0400, Tom Rini wrote:
> On Wed, Jul 01, 2015 at 10:26:21AM -0500, Joe Hershberger wrote:
> > Hi Alexey,
> > 
> > On Wed, Jul 1, 2015 at 9:25 AM, Alexey Brodkin
> > <Alexey.Brodkin@synopsys.com> wrote:
> > > Hi Tom, Joe,
> > > 
> > > On Wed, 2015-07-01 at 22:22 +0800, Bin Meng wrote:
> > > > Hi Alexey,
> > > > 
> > > > On Wed, Jul 1, 2015 at 9:59 PM, Alexey Brodkin
> > > > <Alexey.Brodkin@synopsys.com> wrote:
> > > > > http://git.denx.de/?p=u
> > > > > -boot.git;a=patch;h=f566c9949fbdce2e09a900c5343ca9986e5ba360
> > > > > broke DW GMAC operation if !DM_ETH because eth_write_hwaddr()
> > > > > doesn't
> > > > > exist if !DM_NET.
> > > > > 
> > > > > As for DM_ETH case I'm still not sure if existing 
> > > > > implementation
> > > > > will
> > > > > fly.
> > > > > 
> > > > > The point is as it is said in the comment on "soft reset" 
> > > > > that is
> > > > > triggered with setting DMAMAC_SRST in "busmode" register HW 
> > > > > address
> > > > > gets
> > > > > reset as well. And we inevitably need to set HW address 
> > > > > again.
> > > > > 
> > > > > So probably better solution is to move mentioned "soft-reset" 
> > > > > from
> > > > > "init" (that is used on start of any network activity) to
> > > > > "initialize"
> > > > > (which is only executed once in "board_r" sequence). But 
> > > > > that's a
> > > > > bit of
> > > > > a different story and for now let's just get DW GMAC 
> > > > > functional
> > > > > again.
> > > > > 
> > > > > Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
> > > > > Cc: Joe Hershberger <joe.hershberger@ni.com>
> > > > > Cc: Michal Simek <michal.simek@xilinx.com>
> > > > > Cc: Tom Rini <trini@konsulko.com>
> > > > > ---
> > > > >  drivers/net/designware.c | 4 ++++
> > > > >  1 file changed, 4 insertions(+)
> > > > > 
> > > > > diff --git a/drivers/net/designware.c 
> > > > > b/drivers/net/designware.c
> > > > > index ae51cf3..07281a6 100644
> > > > > --- a/drivers/net/designware.c
> > > > > +++ b/drivers/net/designware.c
> > > > > @@ -243,6 +243,10 @@ static int _dw_eth_init(struct 
> > > > > dw_eth_dev
> > > > > *priv, u8 *enetaddr)
> > > > >                 mdelay(100);
> > > > >         };
> > > > > 
> > > > > +       /* Soft reset above clears HW address registers.
> > > > > +        * So we have to set it here once again */
> > > > > +       _dw_write_hwaddr(priv, enetaddr);
> > > > > +
> > > > >         rx_descs_init(priv);
> > > > >         tx_descs_init(priv);
> > > > > 
> > > > > --
> > > > 
> > > > There is already a patch submitted. Please check
> > > > http://patchwork.ozlabs.org/patch/484214/
> > > 
> > > Any chance for mentioned patch "net: designware: Program MAC 
> > > address to
> > > hardware after soft reset" to be applied?
> > > 
> > > This really fixes GMAC operation and it would be nice to have 
> > > this fix
> > > in upcoming release.
> > 
> > I think that sounds appropriate. Tom?
> 
> Yes.  Of the handful of recent (in my mind anyhow) net patches, are 
> you
> going to do a PR for them or should I just grab things?

Any chance to see that patch upstream anytime soon?

-Alexey