[U-Boot] [U-Boot,v6] arm: atmel: Add SAMA5D2 Xplained board

["Andreas Bießmann" <andreas.devel@googlemail.com>]

Dear Wenyou Yang,

Wenyou Yang <wenyou.yang@atmel.com> writes:
>The board supports following features:
> - Boot media support: SD card/e.MMC/SPI flash,
> - Support LCD display (optional, disabled by default),
> - Support ethernet,
> - Support USB mass storage.
>
>Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
>[fix checkpatch warnings]
>Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>---
>The patch is based on the following patches sent in mailing list.
>	[PATCH] gpio: atmel: Add the PIO4 driver support
>	[PATCH] arm: at91: Change the Chip ID registers' addresses
>	[PATCH v4] mmc: atmel: Add atmel sdhci support
>	[PATCH v3] arm: at91: clock: Add the generated clock support
>
>Changes in v6:
> 1./ change function invocation due to its declaration change,
>	at91_enable_periph_generated_clk().
>
>Changes in v5:
> 1./ remove wrong pin config for USB hw init.
>
>Changes in v4:
> 1./ remove __weak attribute for has_lcdc() added in v3.
> 2./ remove unused goto err_exit.
>
>Changes in v3:
> 1./ change defines-->definitions for more clearly in asm/arch/sama5d2.h.
> 2./ remove unused cpu_is_sama5d2x() macros.
> 3./ fix spelling error "adress".
> 4./ add __weak attribute for has_lcdc().
> 5./ remove SPL configs.
>
>Changes in v2:
> 1./ re-order SAMA5D2 statements alphabetically.
> 2./ remove redundant "Unknown CPU type".
> 3./ rework sama5d2's macros.
> 4./ remove some #ifdef before functions.
> 5./ move CONFIG_CMD_SF to Kconfig.
> 6./ remove NAND macros from config file.
> 7./ CONFIG_BOOTCOMMAND for sf uses defines in at91-sama5_common.h.
>
> arch/arm/mach-at91/Kconfig                       |    5 +
> arch/arm/mach-at91/armv7/Makefile                |    1 +
> arch/arm/mach-at91/armv7/sama5d2_devices.c       |   59 +++++
> arch/arm/mach-at91/include/mach/at91_pmc.h       |    9 +-
> arch/arm/mach-at91/include/mach/atmel_usba_udc.h |    3 +-
> arch/arm/mach-at91/include/mach/hardware.h       |    2 +
> arch/arm/mach-at91/include/mach/sama5d2.h        |  203 ++++++++++++++++
> board/atmel/sama5d2_xplained/Kconfig             |   15 ++
> board/atmel/sama5d2_xplained/MAINTAINERS         |    7 +
> board/atmel/sama5d2_xplained/Makefile            |    8 +
> board/atmel/sama5d2_xplained/sama5d2_xplained.c  |  284 ++++++++++++++++++++++
> configs/sama5d2_xplained_mmc_defconfig           |   11 +
> configs/sama5d2_xplained_spiflash_defconfig      |   11 +
> include/configs/sama5d2_xplained.h               |  122 ++++++++++
> 14 files changed, 734 insertions(+), 6 deletions(-)
> create mode 100644 arch/arm/mach-at91/armv7/sama5d2_devices.c
> create mode 100644 arch/arm/mach-at91/include/mach/sama5d2.h
> create mode 100644 board/atmel/sama5d2_xplained/Kconfig
> create mode 100644 board/atmel/sama5d2_xplained/MAINTAINERS
> create mode 100644 board/atmel/sama5d2_xplained/Makefile
> create mode 100644 board/atmel/sama5d2_xplained/sama5d2_xplained.c
> create mode 100644 configs/sama5d2_xplained_mmc_defconfig
> create mode 100644 configs/sama5d2_xplained_spiflash_defconfig
> create mode 100644 include/configs/sama5d2_xplained.h

applied to u-boot-atmel/master, thanks!

Best regards,
Andreas Bie?mann