From mboxrd@z Thu Jan 1 00:00:00 1970 From: Chin Liang See Date: Wed, 27 Jan 2016 22:16:18 +0800 Subject: [U-Boot] FPGA detection failure on Cyclone V soc development kit In-Reply-To: References: <20160121161800.GZ3359@bill-the-cat> <201601211731.07808.marex@denx.de> <56A25A57.5080707@opensource.altera.com> <1453901681.2348.20.camel@altera.com> Message-ID: <1453904178.2016.2.camel@altera.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On Wed, 2016-01-27 at 13:46 +0000, M?ns Rullg?rd wrote: > Chin Liang See writes: > > > On Fri, 2016-01-22 at 10:35 -0600, Dinh Nguyen wrote: > > > On 01/21/2016 10:31 AM, Marek Vasut wrote: > > > > On Thursday, January 21, 2016 at 05:20:33 PM, M?ns Rullg?rd > > > > wrote: > > > > > Tom Rini writes: > > > > > > On Wed, Jan 20, 2016 at 08:31:30PM +0000, M?ns Rullg?rd > > > > > > wrote: > > > > > > > I'm having a problem with u-boot 2016.01 failing to > > > > > > > detect > > > > > > > the FPGA on my Altera Cyclone V SoC Development Kit. On > > > > > > > startup, it simply prints "FPGA: Not Altera chip ID" (the > > > > > > > ID > > > > > > > having been read as all -zero). No amount of messing > > > > > > > with > > > > > > > jumpers or switches makes a difference. The software on > > > > > > > the > > > > > > > SD card included in the box appears to work, so on a whim > > > > > > > I > > > > > > > took the SPL pre-loader from this card and combined it > > > > > > > with > > > > > > > the main 2016.01 u-boot. This makes the detection > > > > > > > succeed, > > > > > > > despite Marek baulking at this idea. The "good" SPL > > > > > > > identifies as "U-Boot SPL 2013.01.01 (Dec 04 2014 - > > > > > > > 08:59:41)" which is a different build date than the main > > > > > > > u-boot on the same SD card, so which source code version > > > > > > > it > > > > > > > was built from is anyone's guess. > > > > > > > > > > > > > > What's interesting is that Marek's board works with u > > > > > > > -boot > > > > > > > 2016.01 while mine fails even with the very same binary. > > > > > > > The boards are different revisions (his 100-0321003-C1, > > > > > > > mine > > > > > > > -E1), and the main Cyclone V chips are also different > > > > > > > (his > > > > > > > 5CSXFC6D6F31C8NES, mine 5CSXFC6D6F31C6N). > > > > > > > > > > > > > > Any suggestions for what to try next? > > > > > > v2016.01 release or to of tree? If top of tree, try > > > > > > http://patchwork.ozlabs.org/patch/570009/ > > > > > Tried release, top of tree, and top of tree with that patch. > > > > > Nothing works. > > > > Both part number is different in speed grade. This is first time I > > heard about this issue. A quick suspect might due to clock. Can you > > try to copy pll_config.h that is passing (from 2013.01.01) and > > replace > > the one in 2016? > > That doesn't work at all. Now it fails to detect the FPGA, then > hangs > after printing the amount of DRAM. Can you share with me the pll_config for 2013.01.01 that is working for you? We would want to lower down the clock supplied to Scan Manager which spi_m_clk and see whether that helps. Thanks Chin Liang >