* [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface
@ 2016-06-07 22:35 Steve Rae
2016-06-07 22:35 ` [U-Boot] [PATCH v5 2/2] arm: bcm281xx: choose 8-bit phy bus width Steve Rae
2016-06-07 23:52 ` [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface Marek Vasut
0 siblings, 2 replies; 3+ messages in thread
From: Steve Rae @ 2016-06-07 22:35 UTC (permalink / raw)
To: u-boot
Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
physical interface to be 8-bit (rather than 16-bit).
Signed-off-by: Steve Rae <srae@broadcom.com>
---
from [1] (line ~124)
/* The Kona PHY supports an 8-bit wide UTMI interface */
[...snip...]
module_platform_driver(bcm_kona_usb2_driver);
MODULE_ALIAS("platform:bcm-kona-usb2");
MODULE_AUTHOR("Matt Porter <mporter@linaro.org>");
MODULE_DESCRIPTION("BCM Kona USB 2.0 PHY driver");
MODULE_LICENSE("GPL v2");
[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/drivers/phy/phy-bcm-kona-usb2.c
Changes in v5: None
Changes in v4:
- split defconfig's into separate patch (per Marek)
Changes in v3:
- implement Marek's suggestion
Changes in v2:
- implement as Kconfig
drivers/usb/gadget/Kconfig | 10 ++++++++++
drivers/usb/gadget/dwc2_udc_otg.c | 4 ++++
2 files changed, 14 insertions(+)
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index a35a1c7..ae62476 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -52,6 +52,16 @@ config USB_GADGET_DWC2_OTG
driver to operate in Peripheral mode. This option requires
USB_GADGET to be enabled.
+if USB_GADGET_DWC2_OTG
+
+config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
+ bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width"
+ help
+ Set the Designware USB2.0 high-speed OTG controller
+ PHY interface width to 8 bits, rather than the default (16 bits).
+
+endif # USB_GADGET_DWC2_OTG
+
config CI_UDC
bool "ChipIdea device controller"
select USB_GADGET_DUALSPEED
diff --git a/drivers/usb/gadget/dwc2_udc_otg.c b/drivers/usb/gadget/dwc2_udc_otg.c
index cb20b00..a23278d 100644
--- a/drivers/usb/gadget/dwc2_udc_otg.c
+++ b/drivers/usb/gadget/dwc2_udc_otg.c
@@ -415,7 +415,11 @@ static void reconfig_usbd(struct dwc2_udc *dev)
|0<<7 /* Ulpi DDR sel*/
|0<<6 /* 0: high speed utmi+, 1: full speed serial*/
|0<<4 /* 0: utmi+, 1:ulpi*/
+#ifdef CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
+ |0<<3 /* phy i/f 0:8bit, 1:16bit*/
+#else
|1<<3 /* phy i/f 0:8bit, 1:16bit*/
+#endif
|0x7<<0; /* HS/FS Timeout**/
if (dev->pdata->usb_gusbcfg)
--
1.8.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH v5 2/2] arm: bcm281xx: choose 8-bit phy bus width
2016-06-07 22:35 [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface Steve Rae
@ 2016-06-07 22:35 ` Steve Rae
2016-06-07 23:52 ` [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface Marek Vasut
1 sibling, 0 replies; 3+ messages in thread
From: Steve Rae @ 2016-06-07 22:35 UTC (permalink / raw)
To: u-boot
The Kona PHY supports an 8-bit wide UTMI interface,
therefore, choose this Kconfig setting.
Signed-off-by: Steve Rae <srae@broadcom.com>
---
from [1] (line ~124)
/* The Kona PHY supports an 8-bit wide UTMI interface */
[...snip...]
module_platform_driver(bcm_kona_usb2_driver);
MODULE_ALIAS("platform:bcm-kona-usb2");
MODULE_AUTHOR("Matt Porter <mporter@linaro.org>");
MODULE_DESCRIPTION("BCM Kona USB 2.0 PHY driver");
MODULE_LICENSE("GPL v2");
[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/drivers/phy/phy-bcm-kona-usb2.c
Changes in v5:
- update commit message (per Marek)
Changes in v4:
- added this patch
Changes in v3: None
Changes in v2: None
configs/bcm11130_defconfig | 1 +
configs/bcm11130_nand_defconfig | 1 +
configs/bcm28155_ap_defconfig | 1 +
configs/bcm28155_w1d_defconfig | 1 +
4 files changed, 4 insertions(+)
diff --git a/configs/bcm11130_defconfig b/configs/bcm11130_defconfig
index b8ec8ac..2716868 100644
--- a/configs/bcm11130_defconfig
+++ b/configs/bcm11130_defconfig
@@ -18,6 +18,7 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_G_DNL_MANUFACTURER="Broadcom Corporation"
CONFIG_G_DNL_VENDOR_NUM=0x18d1
diff --git a/configs/bcm11130_nand_defconfig b/configs/bcm11130_nand_defconfig
index 6021fd2..8e01c52 100644
--- a/configs/bcm11130_nand_defconfig
+++ b/configs/bcm11130_nand_defconfig
@@ -18,6 +18,7 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_G_DNL_MANUFACTURER="Broadcom Corporation"
CONFIG_G_DNL_VENDOR_NUM=0x18d1
diff --git a/configs/bcm28155_ap_defconfig b/configs/bcm28155_ap_defconfig
index 4404f32..eb58401 100644
--- a/configs/bcm28155_ap_defconfig
+++ b/configs/bcm28155_ap_defconfig
@@ -17,6 +17,7 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_G_DNL_MANUFACTURER="Broadcom Corporation"
CONFIG_G_DNL_VENDOR_NUM=0x18d1
diff --git a/configs/bcm28155_w1d_defconfig b/configs/bcm28155_w1d_defconfig
index 60eb328..35d04af 100644
--- a/configs/bcm28155_w1d_defconfig
+++ b/configs/bcm28155_w1d_defconfig
@@ -18,6 +18,7 @@ CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_G_DNL_MANUFACTURER="Broadcom Corporation"
CONFIG_G_DNL_VENDOR_NUM=0x18d1
--
1.8.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface
2016-06-07 22:35 [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface Steve Rae
2016-06-07 22:35 ` [U-Boot] [PATCH v5 2/2] arm: bcm281xx: choose 8-bit phy bus width Steve Rae
@ 2016-06-07 23:52 ` Marek Vasut
1 sibling, 0 replies; 3+ messages in thread
From: Marek Vasut @ 2016-06-07 23:52 UTC (permalink / raw)
To: u-boot
On 06/08/2016 12:35 AM, Steve Rae wrote:
> Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
> physical interface to be 8-bit (rather than 16-bit).
>
> Signed-off-by: Steve Rae <srae@broadcom.com>
Applied both, thanks.
> ---
> from [1] (line ~124)
>
> /* The Kona PHY supports an 8-bit wide UTMI interface */
> [...snip...]
>
> module_platform_driver(bcm_kona_usb2_driver);
>
> MODULE_ALIAS("platform:bcm-kona-usb2");
> MODULE_AUTHOR("Matt Porter <mporter@linaro.org>");
> MODULE_DESCRIPTION("BCM Kona USB 2.0 PHY driver");
> MODULE_LICENSE("GPL v2");
>
> [1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/drivers/phy/phy-bcm-kona-usb2.c
>
> Changes in v5: None
> Changes in v4:
> - split defconfig's into separate patch (per Marek)
>
> Changes in v3:
> - implement Marek's suggestion
>
> Changes in v2:
> - implement as Kconfig
>
> drivers/usb/gadget/Kconfig | 10 ++++++++++
> drivers/usb/gadget/dwc2_udc_otg.c | 4 ++++
> 2 files changed, 14 insertions(+)
>
> diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
> index a35a1c7..ae62476 100644
> --- a/drivers/usb/gadget/Kconfig
> +++ b/drivers/usb/gadget/Kconfig
> @@ -52,6 +52,16 @@ config USB_GADGET_DWC2_OTG
> driver to operate in Peripheral mode. This option requires
> USB_GADGET to be enabled.
>
> +if USB_GADGET_DWC2_OTG
> +
> +config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
> + bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width"
> + help
> + Set the Designware USB2.0 high-speed OTG controller
> + PHY interface width to 8 bits, rather than the default (16 bits).
> +
> +endif # USB_GADGET_DWC2_OTG
> +
> config CI_UDC
> bool "ChipIdea device controller"
> select USB_GADGET_DUALSPEED
> diff --git a/drivers/usb/gadget/dwc2_udc_otg.c b/drivers/usb/gadget/dwc2_udc_otg.c
> index cb20b00..a23278d 100644
> --- a/drivers/usb/gadget/dwc2_udc_otg.c
> +++ b/drivers/usb/gadget/dwc2_udc_otg.c
> @@ -415,7 +415,11 @@ static void reconfig_usbd(struct dwc2_udc *dev)
> |0<<7 /* Ulpi DDR sel*/
> |0<<6 /* 0: high speed utmi+, 1: full speed serial*/
> |0<<4 /* 0: utmi+, 1:ulpi*/
> +#ifdef CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
> + |0<<3 /* phy i/f 0:8bit, 1:16bit*/
> +#else
> |1<<3 /* phy i/f 0:8bit, 1:16bit*/
> +#endif
> |0x7<<0; /* HS/FS Timeout**/
>
> if (dev->pdata->usb_gusbcfg)
>
--
Best regards,
Marek Vasut
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-06-07 23:52 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-06-07 22:35 [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface Steve Rae
2016-06-07 22:35 ` [U-Boot] [PATCH v5 2/2] arm: bcm281xx: choose 8-bit phy bus width Steve Rae
2016-06-07 23:52 ` [U-Boot] [PATCH v5 1/2] usb: dwc2_udc_otg: support 8-bit interface Marek Vasut
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox