From: Eric Nelson <eric@nelint.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [RFC PATCH 12/12] mx6memcal: add configuration mx6memcal_warpboard_defconfig
Date: Tue, 21 Jun 2016 11:41:42 -0700 [thread overview]
Message-ID: <1466534502-17233-13-git-send-email-eric@nelint.com> (raw)
In-Reply-To: <1466534502-17233-1-git-send-email-eric@nelint.com>
Signed-off-by: Eric Nelson <eric@nelint.com>
---
Note that I haven't tested this board because I don't currently have one.
configs/mx6memcal_warpboard_defconfig | 32 ++++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
create mode 100644 configs/mx6memcal_warpboard_defconfig
diff --git a/configs/mx6memcal_warpboard_defconfig b/configs/mx6memcal_warpboard_defconfig
new file mode 100644
index 0000000..0ec1b3c
--- /dev/null
+++ b/configs/mx6memcal_warpboard_defconfig
@@ -0,0 +1,32 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_MX6_DDRCAL=y
+CONFIG_TARGET_MX6MEMCAL=y
+CONFIG_DDRWIDTH=32
+CONFIG_DDRCS=1
+CONFIG_LPDDR2=y
+CONFIG_MT29PZZZ4D4BKESK=y
+CONFIG_DRAM_DRIVE_STRENGTH=4
+CONFIG_RALAT=2
+CONFIG_UART1_UART1=y
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6SL"
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_BOOTM is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_GO is not set
+# CONFIG_CMD_RUN is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_SAVEENV is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_NFS is not set
--
2.7.4
next prev parent reply other threads:[~2016-06-21 18:41 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-21 18:41 [U-Boot] [RFC PATCH 00/12] imx: mx6: add virtual mx6memcal board Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 01/12] imx: mx6: ddr: return output of calibration routines Eric Nelson
2016-06-22 23:18 ` Marek Vasut
2016-06-22 23:52 ` Eric Nelson
2016-06-22 23:57 ` Marek Vasut
2016-06-23 0:18 ` Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 02/12] novena: supply calibration parameter to DDR " Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 03/12] imx: mx6: ddr: make calibration optional in config routines Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 04/12] imx: mx6: ddr: pass sysinfo to calibration routines Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 05/12] novena: pass mx6_ddr_sysinfo " Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 06/12] imx: mx6: ddr: use Kconfig for inclusion of DDR calibration Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 07/12] novena_defconfig: select MX6_DDRCAL Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 08/12] mx6: Add board mx6memcal for use in validating DDR Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 09/12] mx6memcal: add configuration mx6memcal_mx6slevk_defconfig Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 10/12] mx6memcal: add configuration mx6memcal_nitrogen6_max_defconfig Eric Nelson
2016-06-21 18:41 ` [U-Boot] [RFC PATCH 11/12] mx6memcal: add configuration mx6memcal_sabrelite_defconfig Eric Nelson
2016-06-21 18:41 ` Eric Nelson [this message]
2016-06-21 19:48 ` [U-Boot] i.MX SPL tools (was Re: [RFC PATCH 00/12] imx: mx6: add virtual mx6memcal board) Eric Nelson
2016-06-24 23:26 ` Tom Rini
2016-08-26 15:00 ` [U-Boot] [RFC PATCH 00/12] imx: mx6: add virtual mx6memcal board Tim Harvey
2016-08-26 15:33 ` Eric Nelson
2016-08-26 16:46 ` Fabio Estevam
2016-08-26 20:34 ` Tim Harvey
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1466534502-17233-13-git-send-email-eric@nelint.com \
--to=eric@nelint.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox