* [U-Boot] [PATCH v7 1/5] net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
@ 2016-10-19 11:23 ` Jagan Teki
2016-10-19 11:23 ` [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model Jagan Teki
` (5 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Jagan Teki @ 2016-10-19 11:23 UTC (permalink / raw)
To: u-boot
fec_get_hwaddr never used eth_device argument, hence removed.
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
---
drivers/net/fec_mxc.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 8e3b839..0838d58 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -362,8 +362,7 @@ static void fec_rbd_clean(int last, struct fec_bd *pRbd)
writew(0, &pRbd->data_length);
}
-static int fec_get_hwaddr(struct eth_device *dev, int dev_id,
- unsigned char *mac)
+static int fec_get_hwaddr(int dev_id, unsigned char *mac)
{
imx_get_mac_from_fuse(dev_id, mac);
return !is_valid_ethaddr(mac);
@@ -1045,7 +1044,7 @@ static int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr,
#endif
eth_register(edev);
- if (fec_get_hwaddr(edev, dev_id, ethaddr) == 0) {
+ if (fec_get_hwaddr(dev_id, ethaddr) == 0) {
debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr);
memcpy(edev->enetaddr, ethaddr, 6);
if (!getenv("ethaddr"))
--
2.7.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
2016-10-19 11:23 ` [U-Boot] [PATCH v7 1/5] net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr Jagan Teki
@ 2016-10-19 11:23 ` Jagan Teki
2016-10-19 17:35 ` Jagan Teki
2016-10-19 18:02 ` Joe Hershberger
2016-10-19 11:23 ` [U-Boot] [PATCH v7 3/5] net: fec_mxc: Driver cleanups Jagan Teki
` (4 subsequent siblings)
6 siblings, 2 replies; 11+ messages in thread
From: Jagan Teki @ 2016-10-19 11:23 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
This patch add driver model support for fec_mxc driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
drivers/net/fec_mxc.c | 313 ++++++++++++++++++++++++++++++++++++++++++--------
drivers/net/fec_mxc.h | 4 +
2 files changed, 270 insertions(+), 47 deletions(-)
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 0838d58..8c0927c 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -9,6 +9,7 @@
*/
#include <common.h>
+#include <dm.h>
#include <malloc.h>
#include <memalign.h>
#include <net.h>
@@ -368,11 +369,8 @@ static int fec_get_hwaddr(int dev_id, unsigned char *mac)
return !is_valid_ethaddr(mac);
}
-static int fec_set_hwaddr(struct eth_device *dev)
+static int _fec_set_hwaddr(struct fec_priv *fec, uchar *mac)
{
- uchar *mac = dev->enetaddr;
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-
writel(0, &fec->eth->iaddr1);
writel(0, &fec->eth->iaddr2);
writel(0, &fec->eth->gaddr1);
@@ -426,9 +424,8 @@ static void fec_reg_setup(struct fec_priv *fec)
* Start the FEC engine
* @param[in] dev Our device to handle
*/
-static int fec_open(struct eth_device *edev)
+static int fec_open(struct fec_priv *fec)
{
- struct fec_priv *fec = (struct fec_priv *)edev->priv;
int speed;
uint32_t addr, size;
int i;
@@ -534,14 +531,13 @@ static int fec_open(struct eth_device *edev)
return 0;
}
-static int fec_init(struct eth_device *dev, bd_t* bd)
+static int _fec_init(struct fec_priv *fec, uchar *mac)
{
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
uint32_t mib_ptr = (uint32_t)&fec->eth->rmon_t_drop;
int i;
/* Initialize MAC address */
- fec_set_hwaddr(dev);
+ _fec_set_hwaddr(fec, mac);
/*
* Setup transmit descriptors, there are two in total.
@@ -587,7 +583,7 @@ static int fec_init(struct eth_device *dev, bd_t* bd)
if (fec->xcv_type != SEVENWIRE)
miiphy_restart_aneg(dev);
#endif
- fec_open(dev);
+ fec_open(fec);
return 0;
}
@@ -595,9 +591,8 @@ static int fec_init(struct eth_device *dev, bd_t* bd)
* Halt the FEC engine
* @param[in] dev Our device to handle
*/
-static void fec_halt(struct eth_device *dev)
+static void _fec_halt(struct fec_priv *fec)
{
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
int counter = 0xffff;
/*
@@ -637,7 +632,7 @@ static void fec_halt(struct eth_device *dev)
* @param[in] length Data count in bytes
* @return 0 on success
*/
-static int fec_send(struct eth_device *dev, void *packet, int length)
+static int _fec_send(struct fec_priv *fec, void *packet, int length)
{
unsigned int status;
uint32_t size, end;
@@ -649,8 +644,6 @@ static int fec_send(struct eth_device *dev, void *packet, int length)
* This routine transmits one frame. This routine only accepts
* 6-byte Ethernet addresses.
*/
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-
/*
* Check for valid length of data.
*/
@@ -777,14 +770,14 @@ out:
return ret;
}
+
/**
* Pull one frame from the card
* @param[in] dev Our ethernet device to handle
* @return Length of packet read
*/
-static int fec_recv(struct eth_device *dev)
+static int _fec_recv(struct fec_priv *fec, uchar *mac)
{
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
struct fec_bd *rbd = &fec->rbd_base[fec->rbd_index];
unsigned long ievent;
int frame_length, len = 0;
@@ -800,8 +793,8 @@ static int fec_recv(struct eth_device *dev)
writel(ievent, &fec->eth->ievent);
debug("fec_recv: ievent 0x%lx\n", ievent);
if (ievent & FEC_IEVENT_BABR) {
- fec_halt(dev);
- fec_init(dev, fec->bd);
+ _fec_halt(fec);
+ _fec_init(fec, mac);
printf("some error: 0x%08lx\n", ievent);
return 0;
}
@@ -813,10 +806,10 @@ static int fec_recv(struct eth_device *dev)
if (ievent & FEC_IEVENT_GRA) {
/* Graceful stop complete */
if (readl(&fec->eth->x_cntrl) & 0x00000001) {
- fec_halt(dev);
+ _fec_halt(fec);
writel(~0x00000001 & readl(&fec->eth->x_cntrl),
&fec->eth->x_cntrl);
- fec_init(dev, fec->bd);
+ _fec_init(fec, mac);
}
}
@@ -970,6 +963,71 @@ static void fec_free_descs(struct fec_priv *fec)
free(fec->tbd_base);
}
+struct mii_dev *fec_get_miibus(uint32_t base_addr, int dev_id)
+{
+ struct ethernet_regs *eth = (struct ethernet_regs *)base_addr;
+ struct mii_dev *bus;
+ int ret;
+
+ bus = mdio_alloc();
+ if (!bus) {
+ printf("mdio_alloc failed\n");
+ return NULL;
+ }
+ bus->read = fec_phy_read;
+ bus->write = fec_phy_write;
+ bus->priv = eth;
+ fec_set_dev_name(bus->name, dev_id);
+
+ ret = mdio_register(bus);
+ if (ret) {
+ printf("mdio_register failed\n");
+ free(bus);
+ return NULL;
+ }
+ fec_mii_setspeed(eth);
+ return bus;
+}
+
+#ifndef CONFIG_DM_ETH
+static int fec_recv(struct eth_device *dev)
+{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ uchar *mac = dev->enetaddr;
+
+ return _fec_recv(fec, mac);
+}
+
+static int fec_send(struct eth_device *dev, void *packet, int length)
+{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+
+ return _fec_send(fec, packet, length);
+}
+
+static void fec_halt(struct eth_device *dev)
+{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+
+ _fec_halt(fec);
+}
+
+static int fec_set_hwaddr(struct eth_device *dev)
+{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ uchar *mac = dev->enetaddr;
+
+ return _fec_set_hwaddr(fec, mac);
+}
+
+static int fec_init(struct eth_device *dev, bd_t *bd)
+{
+ struct fec_priv *fec = (struct fec_priv *)dev->priv;
+ uchar *mac = dev->enetaddr;
+
+ return _fec_init(fec, mac);
+}
+
#ifdef CONFIG_PHYLIB
int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr,
struct mii_dev *bus, struct phy_device *phydev)
@@ -1061,32 +1119,6 @@ err1:
return ret;
}
-struct mii_dev *fec_get_miibus(uint32_t base_addr, int dev_id)
-{
- struct ethernet_regs *eth = (struct ethernet_regs *)base_addr;
- struct mii_dev *bus;
- int ret;
-
- bus = mdio_alloc();
- if (!bus) {
- printf("mdio_alloc failed\n");
- return NULL;
- }
- bus->read = fec_phy_read;
- bus->write = fec_phy_write;
- bus->priv = eth;
- fec_set_dev_name(bus->name, dev_id);
-
- ret = mdio_register(bus);
- if (ret) {
- printf("mdio_register failed\n");
- free(bus);
- return NULL;
- }
- fec_mii_setspeed(eth);
- return bus;
-}
-
int fecmxc_initialize_multi(bd_t *bd, int dev_id, int phy_id, uint32_t addr)
{
uint32_t base_mii;
@@ -1146,3 +1178,190 @@ int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int))
return 0;
}
#endif
+
+#else
+
+static int fec_set_hwaddr(struct udevice *dev)
+{
+ struct fec_priv *fec = dev_get_priv(dev);
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+ uchar *mac = pdata->enetaddr;
+
+ return _fec_set_hwaddr(fec, mac);
+}
+
+static void fec_halt(struct udevice *dev)
+{
+ struct fec_priv *fec = dev_get_priv(dev);
+
+ _fec_halt(fec);
+}
+
+static int fec_recv(struct udevice *dev, int flags, uchar **packetp)
+{
+ struct fec_priv *fec = dev_get_priv(dev);
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+ uchar *mac = pdata->enetaddr;
+
+ return _fec_recv(fec, mac);
+}
+
+static int fec_send(struct udevice *dev, void *packet, int length)
+{
+ struct fec_priv *fec = dev_get_priv(dev);
+
+ return _fec_send(fec, packet, length);
+}
+
+static int fec_init(struct udevice *dev)
+{
+ struct fec_priv *fec = dev_get_priv(dev);
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+ uchar *mac = pdata->enetaddr;
+
+ return _fec_init(fec, mac);
+}
+
+static const struct eth_ops fecmxc_ops = {
+ .start = fec_init,
+ .send = fec_send,
+ .recv = fec_recv,
+ .stop = fec_halt,
+ .write_hwaddr = fec_set_hwaddr,
+};
+
+static int fec_phy_init(struct fec_priv *priv, struct udevice *dev)
+{
+ struct phy_device *phydev;
+ int mask = 0xffffffff;
+
+#ifdef CONFIG_PHYLIB
+ mask = 1 << CONFIG_FEC_MXC_PHYADDR;
+#endif
+
+ phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
+ if (!phydev)
+ return -ENODEV;
+
+ phy_connect_dev(phydev, dev);
+
+ priv->phydev = phydev;
+ phy_config(phydev);
+
+ return 0;
+}
+
+static int fecmxc_probe(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+ struct fec_priv *priv = dev_get_priv(dev);
+ struct mii_dev *bus = NULL;
+ int dev_id = -1;
+ unsigned char ethaddr[6];
+ uint32_t start;
+ int ret;
+
+ ret = fec_alloc_descs(priv);
+ if (ret)
+ return ret;
+
+ bus = fec_get_miibus((uint32_t)priv->eth, dev_id);
+ if (!bus)
+ goto err_mii;
+
+ priv->bus = bus;
+ priv->xcv_type = CONFIG_FEC_XCV_TYPE;
+ priv->interface = pdata->phy_interface;
+ ret = fec_phy_init(priv, dev);
+ if (ret)
+ goto err_phy;
+
+ /* Reset chip. */
+ writel(readl(&priv->eth->ecntrl) | FEC_ECNTRL_RESET, &priv->eth->ecntrl);
+ start = get_timer(0);
+ while (readl(&priv->eth->ecntrl) & FEC_ECNTRL_RESET) {
+ if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
+ printf("FEC MXC: Timeout reseting chip\n");
+ goto err_timeout;
+ }
+ udelay(10);
+ }
+
+ fec_reg_setup(priv);
+ priv->dev_id = (dev_id == -1) ? 0 : dev_id;
+
+ ret = fec_get_hwaddr(dev_id, ethaddr);
+ if (!ret) {
+ debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr);
+ memcpy(pdata->enetaddr, ethaddr, 6);
+ if (!getenv("ethaddr"))
+ eth_setenv_enetaddr("ethaddr", ethaddr);
+ }
+
+ return 0;
+
+err_timeout:
+ free(priv->phydev);
+err_phy:
+ mdio_unregister(bus);
+ free(bus);
+err_mii:
+ fec_free_descs(priv);
+ return ret;
+}
+
+static int fecmxc_remove(struct udevice *dev)
+{
+ struct fec_priv *priv = dev_get_priv(dev);
+
+ free(priv->phydev);
+ fec_free_descs(priv);
+ mdio_unregister(priv->bus);
+ mdio_free(priv->bus);
+
+ return 0;
+}
+
+static int fecmxc_ofdata_to_platdata(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+ struct fec_priv *priv = dev_get_priv(dev);
+ const char *phy_mode;
+
+ pdata->iobase = (phys_addr_t)dev_get_addr(dev);
+ priv->eth = (struct ethernet_regs *)pdata->iobase;
+
+ pdata->phy_interface = -1;
+ phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL);
+ if (phy_mode)
+ pdata->phy_interface = phy_get_interface_by_name(phy_mode);
+ if (pdata->phy_interface == -1) {
+ debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
+ return -EINVAL;
+ }
+
+ /* TODO
+ * Need to get the reset-gpio and related properties from DT
+ * and implemet the enet reset code on .probe call
+ */
+
+ return 0;
+}
+
+static const struct udevice_id fecmxc_ids[] = {
+ { .compatible = "fsl,imx6q-fec" },
+ { }
+};
+
+U_BOOT_DRIVER(fec_gem) = {
+ .name = "fecmxc",
+ .id = UCLASS_ETH,
+ .of_match = fecmxc_ids,
+ .ofdata_to_platdata = fecmxc_ofdata_to_platdata,
+ .probe = fecmxc_probe,
+ .remove = fecmxc_remove,
+ .ops = &fecmxc_ops,
+ .priv_auto_alloc_size = sizeof(struct fec_priv),
+ .platdata_auto_alloc_size = sizeof(struct eth_pdata),
+};
+#endif
diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
index 0717cc6..9fc6153 100644
--- a/drivers/net/fec_mxc.h
+++ b/drivers/net/fec_mxc.h
@@ -264,6 +264,10 @@ struct fec_priv {
int phy_id;
int (*mii_postcall)(int);
#endif
+
+#ifdef CONFIG_DM_ETH
+ u32 interface;
+#endif
};
/**
--
2.7.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model
2016-10-19 11:23 ` [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model Jagan Teki
@ 2016-10-19 17:35 ` Jagan Teki
2016-10-19 18:02 ` Joe Hershberger
1 sibling, 0 replies; 11+ messages in thread
From: Jagan Teki @ 2016-10-19 17:35 UTC (permalink / raw)
To: u-boot
Hi Joe,
On Wed, Oct 19, 2016 at 4:53 PM, Jagan Teki <jteki@openedev.com> wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> This patch add driver model support for fec_mxc driver.
>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Joe Hershberger <joe.hershberger@ni.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> drivers/net/fec_mxc.c | 313 ++++++++++++++++++++++++++++++++++++++++++--------
> drivers/net/fec_mxc.h | 4 +
> 2 files changed, 270 insertions(+), 47 deletions(-)
>
> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
> index 0838d58..8c0927c 100644
> --- a/drivers/net/fec_mxc.c
> +++ b/drivers/net/fec_mxc.c
> @@ -9,6 +9,7 @@
> */
>
> #include <common.h>
> +#include <dm.h>
> #include <malloc.h>
> #include <memalign.h>
> #include <net.h>
> @@ -368,11 +369,8 @@ static int fec_get_hwaddr(int dev_id, unsigned char *mac)
> return !is_valid_ethaddr(mac);
> }
>
> -static int fec_set_hwaddr(struct eth_device *dev)
> +static int _fec_set_hwaddr(struct fec_priv *fec, uchar *mac)
> {
> - uchar *mac = dev->enetaddr;
> - struct fec_priv *fec = (struct fec_priv *)dev->priv;
> -
> writel(0, &fec->eth->iaddr1);
> writel(0, &fec->eth->iaddr2);
> writel(0, &fec->eth->gaddr1);
> @@ -426,9 +424,8 @@ static void fec_reg_setup(struct fec_priv *fec)
> * Start the FEC engine
> * @param[in] dev Our device to handle
> */
> -static int fec_open(struct eth_device *edev)
> +static int fec_open(struct fec_priv *fec)
> {
> - struct fec_priv *fec = (struct fec_priv *)edev->priv;
> int speed;
> uint32_t addr, size;
> int i;
> @@ -534,14 +531,13 @@ static int fec_open(struct eth_device *edev)
> return 0;
> }
>
> -static int fec_init(struct eth_device *dev, bd_t* bd)
> +static int _fec_init(struct fec_priv *fec, uchar *mac)
> {
> - struct fec_priv *fec = (struct fec_priv *)dev->priv;
> uint32_t mib_ptr = (uint32_t)&fec->eth->rmon_t_drop;
> int i;
>
> /* Initialize MAC address */
> - fec_set_hwaddr(dev);
> + _fec_set_hwaddr(fec, mac);
>
> /*
> * Setup transmit descriptors, there are two in total.
> @@ -587,7 +583,7 @@ static int fec_init(struct eth_device *dev, bd_t* bd)
> if (fec->xcv_type != SEVENWIRE)
> miiphy_restart_aneg(dev);
> #endif
> - fec_open(dev);
> + fec_open(fec);
> return 0;
> }
>
> @@ -595,9 +591,8 @@ static int fec_init(struct eth_device *dev, bd_t* bd)
> * Halt the FEC engine
> * @param[in] dev Our device to handle
> */
> -static void fec_halt(struct eth_device *dev)
> +static void _fec_halt(struct fec_priv *fec)
> {
> - struct fec_priv *fec = (struct fec_priv *)dev->priv;
> int counter = 0xffff;
>
> /*
> @@ -637,7 +632,7 @@ static void fec_halt(struct eth_device *dev)
> * @param[in] length Data count in bytes
> * @return 0 on success
> */
> -static int fec_send(struct eth_device *dev, void *packet, int length)
> +static int _fec_send(struct fec_priv *fec, void *packet, int length)
> {
> unsigned int status;
> uint32_t size, end;
> @@ -649,8 +644,6 @@ static int fec_send(struct eth_device *dev, void *packet, int length)
> * This routine transmits one frame. This routine only accepts
> * 6-byte Ethernet addresses.
> */
> - struct fec_priv *fec = (struct fec_priv *)dev->priv;
> -
> /*
> * Check for valid length of data.
> */
> @@ -777,14 +770,14 @@ out:
> return ret;
> }
>
> +
> /**
> * Pull one frame from the card
> * @param[in] dev Our ethernet device to handle
> * @return Length of packet read
> */
> -static int fec_recv(struct eth_device *dev)
> +static int _fec_recv(struct fec_priv *fec, uchar *mac)
> {
> - struct fec_priv *fec = (struct fec_priv *)dev->priv;
> struct fec_bd *rbd = &fec->rbd_base[fec->rbd_index];
> unsigned long ievent;
> int frame_length, len = 0;
> @@ -800,8 +793,8 @@ static int fec_recv(struct eth_device *dev)
> writel(ievent, &fec->eth->ievent);
> debug("fec_recv: ievent 0x%lx\n", ievent);
> if (ievent & FEC_IEVENT_BABR) {
> - fec_halt(dev);
> - fec_init(dev, fec->bd);
> + _fec_halt(fec);
> + _fec_init(fec, mac);
> printf("some error: 0x%08lx\n", ievent);
> return 0;
> }
> @@ -813,10 +806,10 @@ static int fec_recv(struct eth_device *dev)
> if (ievent & FEC_IEVENT_GRA) {
> /* Graceful stop complete */
> if (readl(&fec->eth->x_cntrl) & 0x00000001) {
> - fec_halt(dev);
> + _fec_halt(fec);
> writel(~0x00000001 & readl(&fec->eth->x_cntrl),
> &fec->eth->x_cntrl);
> - fec_init(dev, fec->bd);
> + _fec_init(fec, mac);
> }
> }
>
> @@ -970,6 +963,71 @@ static void fec_free_descs(struct fec_priv *fec)
> free(fec->tbd_base);
> }
>
> +struct mii_dev *fec_get_miibus(uint32_t base_addr, int dev_id)
> +{
> + struct ethernet_regs *eth = (struct ethernet_regs *)base_addr;
> + struct mii_dev *bus;
> + int ret;
> +
> + bus = mdio_alloc();
> + if (!bus) {
> + printf("mdio_alloc failed\n");
> + return NULL;
> + }
> + bus->read = fec_phy_read;
> + bus->write = fec_phy_write;
> + bus->priv = eth;
> + fec_set_dev_name(bus->name, dev_id);
> +
> + ret = mdio_register(bus);
> + if (ret) {
> + printf("mdio_register failed\n");
> + free(bus);
> + return NULL;
> + }
> + fec_mii_setspeed(eth);
> + return bus;
> +}
> +
> +#ifndef CONFIG_DM_ETH
> +static int fec_recv(struct eth_device *dev)
> +{
> + struct fec_priv *fec = (struct fec_priv *)dev->priv;
> + uchar *mac = dev->enetaddr;
> +
> + return _fec_recv(fec, mac);
> +}
> +
> +static int fec_send(struct eth_device *dev, void *packet, int length)
> +{
> + struct fec_priv *fec = (struct fec_priv *)dev->priv;
> +
> + return _fec_send(fec, packet, length);
> +}
> +
> +static void fec_halt(struct eth_device *dev)
> +{
> + struct fec_priv *fec = (struct fec_priv *)dev->priv;
> +
> + _fec_halt(fec);
> +}
> +
> +static int fec_set_hwaddr(struct eth_device *dev)
> +{
> + struct fec_priv *fec = (struct fec_priv *)dev->priv;
> + uchar *mac = dev->enetaddr;
> +
> + return _fec_set_hwaddr(fec, mac);
> +}
> +
> +static int fec_init(struct eth_device *dev, bd_t *bd)
> +{
> + struct fec_priv *fec = (struct fec_priv *)dev->priv;
> + uchar *mac = dev->enetaddr;
> +
> + return _fec_init(fec, mac);
> +}
> +
> #ifdef CONFIG_PHYLIB
> int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr,
> struct mii_dev *bus, struct phy_device *phydev)
> @@ -1061,32 +1119,6 @@ err1:
> return ret;
> }
>
> -struct mii_dev *fec_get_miibus(uint32_t base_addr, int dev_id)
> -{
> - struct ethernet_regs *eth = (struct ethernet_regs *)base_addr;
> - struct mii_dev *bus;
> - int ret;
> -
> - bus = mdio_alloc();
> - if (!bus) {
> - printf("mdio_alloc failed\n");
> - return NULL;
> - }
> - bus->read = fec_phy_read;
> - bus->write = fec_phy_write;
> - bus->priv = eth;
> - fec_set_dev_name(bus->name, dev_id);
> -
> - ret = mdio_register(bus);
> - if (ret) {
> - printf("mdio_register failed\n");
> - free(bus);
> - return NULL;
> - }
> - fec_mii_setspeed(eth);
> - return bus;
> -}
> -
> int fecmxc_initialize_multi(bd_t *bd, int dev_id, int phy_id, uint32_t addr)
> {
> uint32_t base_mii;
> @@ -1146,3 +1178,190 @@ int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int))
> return 0;
> }
> #endif
> +
> +#else
> +
> +static int fec_set_hwaddr(struct udevice *dev)
> +{
> + struct fec_priv *fec = dev_get_priv(dev);
> + struct eth_pdata *pdata = dev_get_platdata(dev);
> + uchar *mac = pdata->enetaddr;
> +
> + return _fec_set_hwaddr(fec, mac);
> +}
> +
> +static void fec_halt(struct udevice *dev)
> +{
> + struct fec_priv *fec = dev_get_priv(dev);
> +
> + _fec_halt(fec);
> +}
> +
> +static int fec_recv(struct udevice *dev, int flags, uchar **packetp)
> +{
> + struct fec_priv *fec = dev_get_priv(dev);
> + struct eth_pdata *pdata = dev_get_platdata(dev);
> + uchar *mac = pdata->enetaddr;
> +
> + return _fec_recv(fec, mac);
> +}
> +
> +static int fec_send(struct udevice *dev, void *packet, int length)
> +{
> + struct fec_priv *fec = dev_get_priv(dev);
> +
> + return _fec_send(fec, packet, length);
> +}
> +
> +static int fec_init(struct udevice *dev)
> +{
> + struct fec_priv *fec = dev_get_priv(dev);
> + struct eth_pdata *pdata = dev_get_platdata(dev);
> + uchar *mac = pdata->enetaddr;
> +
> + return _fec_init(fec, mac);
> +}
> +
> +static const struct eth_ops fecmxc_ops = {
> + .start = fec_init,
> + .send = fec_send,
> + .recv = fec_recv,
> + .stop = fec_halt,
> + .write_hwaddr = fec_set_hwaddr,
> +};
> +
> +static int fec_phy_init(struct fec_priv *priv, struct udevice *dev)
> +{
> + struct phy_device *phydev;
> + int mask = 0xffffffff;
> +
> +#ifdef CONFIG_PHYLIB
> + mask = 1 << CONFIG_FEC_MXC_PHYADDR;
> +#endif
> +
> + phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
> + if (!phydev)
> + return -ENODEV;
> +
> + phy_connect_dev(phydev, dev);
> +
> + priv->phydev = phydev;
> + phy_config(phydev);
> +
> + return 0;
> +}
> +
> +static int fecmxc_probe(struct udevice *dev)
> +{
> + struct eth_pdata *pdata = dev_get_platdata(dev);
> + struct fec_priv *priv = dev_get_priv(dev);
> + struct mii_dev *bus = NULL;
> + int dev_id = -1;
> + unsigned char ethaddr[6];
> + uint32_t start;
> + int ret;
> +
> + ret = fec_alloc_descs(priv);
> + if (ret)
> + return ret;
> +
> + bus = fec_get_miibus((uint32_t)priv->eth, dev_id);
> + if (!bus)
> + goto err_mii;
> +
> + priv->bus = bus;
> + priv->xcv_type = CONFIG_FEC_XCV_TYPE;
> + priv->interface = pdata->phy_interface;
> + ret = fec_phy_init(priv, dev);
> + if (ret)
> + goto err_phy;
> +
> + /* Reset chip. */
> + writel(readl(&priv->eth->ecntrl) | FEC_ECNTRL_RESET, &priv->eth->ecntrl);
> + start = get_timer(0);
> + while (readl(&priv->eth->ecntrl) & FEC_ECNTRL_RESET) {
> + if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
> + printf("FEC MXC: Timeout reseting chip\n");
> + goto err_timeout;
> + }
> + udelay(10);
> + }
> +
> + fec_reg_setup(priv);
> + priv->dev_id = (dev_id == -1) ? 0 : dev_id;
> +
> + ret = fec_get_hwaddr(dev_id, ethaddr);
> + if (!ret) {
> + debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr);
> + memcpy(pdata->enetaddr, ethaddr, 6);
> + if (!getenv("ethaddr"))
> + eth_setenv_enetaddr("ethaddr", ethaddr);
> + }
> +
> + return 0;
> +
> +err_timeout:
> + free(priv->phydev);
> +err_phy:
> + mdio_unregister(bus);
> + free(bus);
> +err_mii:
> + fec_free_descs(priv);
> + return ret;
> +}
> +
> +static int fecmxc_remove(struct udevice *dev)
> +{
> + struct fec_priv *priv = dev_get_priv(dev);
> +
> + free(priv->phydev);
> + fec_free_descs(priv);
> + mdio_unregister(priv->bus);
> + mdio_free(priv->bus);
> +
> + return 0;
> +}
> +
> +static int fecmxc_ofdata_to_platdata(struct udevice *dev)
> +{
> + struct eth_pdata *pdata = dev_get_platdata(dev);
> + struct fec_priv *priv = dev_get_priv(dev);
> + const char *phy_mode;
> +
> + pdata->iobase = (phys_addr_t)dev_get_addr(dev);
> + priv->eth = (struct ethernet_regs *)pdata->iobase;
> +
> + pdata->phy_interface = -1;
> + phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL);
> + if (phy_mode)
> + pdata->phy_interface = phy_get_interface_by_name(phy_mode);
> + if (pdata->phy_interface == -1) {
> + debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
> + return -EINVAL;
> + }
> +
> + /* TODO
> + * Need to get the reset-gpio and related properties from DT
> + * and implemet the enet reset code on .probe call
> + */
> +
> + return 0;
> +}
> +
> +static const struct udevice_id fecmxc_ids[] = {
> + { .compatible = "fsl,imx6q-fec" },
> + { }
> +};
> +
> +U_BOOT_DRIVER(fec_gem) = {
> + .name = "fecmxc",
> + .id = UCLASS_ETH,
> + .of_match = fecmxc_ids,
> + .ofdata_to_platdata = fecmxc_ofdata_to_platdata,
> + .probe = fecmxc_probe,
> + .remove = fecmxc_remove,
> + .ops = &fecmxc_ops,
> + .priv_auto_alloc_size = sizeof(struct fec_priv),
> + .platdata_auto_alloc_size = sizeof(struct eth_pdata),
> +};
> +#endif
> diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
> index 0717cc6..9fc6153 100644
> --- a/drivers/net/fec_mxc.h
> +++ b/drivers/net/fec_mxc.h
> @@ -264,6 +264,10 @@ struct fec_priv {
> int phy_id;
> int (*mii_postcall)(int);
> #endif
> +
> +#ifdef CONFIG_DM_ETH
> + u32 interface;
> +#endif
> };
>
Any comment, otherwise please add Acked/Reviewd - We would like to
apply this trough Stefanos'.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model
2016-10-19 11:23 ` [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model Jagan Teki
2016-10-19 17:35 ` Jagan Teki
@ 2016-10-19 18:02 ` Joe Hershberger
1 sibling, 0 replies; 11+ messages in thread
From: Joe Hershberger @ 2016-10-19 18:02 UTC (permalink / raw)
To: u-boot
On Wed, Oct 19, 2016 at 6:23 AM, Jagan Teki <jteki@openedev.com> wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> This patch add driver model support for fec_mxc driver.
>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Joe Hershberger <joe.hershberger@ni.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v7 3/5] net: fec_mxc: Driver cleanups
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
2016-10-19 11:23 ` [U-Boot] [PATCH v7 1/5] net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr Jagan Teki
2016-10-19 11:23 ` [U-Boot] [PATCH v7 2/5] net: fec_mxc: Convert into driver model Jagan Teki
@ 2016-10-19 11:23 ` Jagan Teki
2016-10-19 11:23 ` [U-Boot] [PATCH v7 4/5] ARM: dts: imx6qdl-icore: Add FEC support Jagan Teki
` (3 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Jagan Teki @ 2016-10-19 11:23 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
- Remove exctra space
- Add space
- Add tab space
- Fix single line comments quotes
- Fix 'CHECK: Avoid CamelCase'
- Fix 'CHECK: Alignment should match open parenthesis'
- Fix 'WARNING: line over 80 characters'
- Re-arrage header include files
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
drivers/net/fec_mxc.c | 200 +++++++++++++++++++-------------------------------
drivers/net/fec_mxc.h | 27 ++-----
2 files changed, 82 insertions(+), 145 deletions(-)
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 8c0927c..23fa609 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -12,18 +12,19 @@
#include <dm.h>
#include <malloc.h>
#include <memalign.h>
+#include <miiphy.h>
#include <net.h>
#include <netdev.h>
-#include <miiphy.h>
#include "fec_mxc.h"
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/imx-common/sys_proto.h>
#include <asm/io.h>
#include <linux/errno.h>
#include <linux/compiler.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/sys_proto.h>
+
DECLARE_GLOBAL_DATA_PTR;
/*
@@ -80,11 +81,9 @@ static void swap_packet(uint32_t *packet, int length)
}
#endif
-/*
- * MII-interface related functions
- */
-static int fec_mdio_read(struct ethernet_regs *eth, uint8_t phyAddr,
- uint8_t regAddr)
+/* MII-interface related functions */
+static int fec_mdio_read(struct ethernet_regs *eth, uint8_t phyaddr,
+ uint8_t regaddr)
{
uint32_t reg; /* convenient holder for the PHY register */
uint32_t phy; /* convenient holder for the PHY */
@@ -96,15 +95,13 @@ static int fec_mdio_read(struct ethernet_regs *eth, uint8_t phyAddr,
* programming the FEC's MII data register.
*/
writel(FEC_IEVENT_MII, ð->ievent);
- reg = regAddr << FEC_MII_DATA_RA_SHIFT;
- phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
+ reg = regaddr << FEC_MII_DATA_RA_SHIFT;
+ phy = phyaddr << FEC_MII_DATA_PA_SHIFT;
writel(FEC_MII_DATA_ST | FEC_MII_DATA_OP_RD | FEC_MII_DATA_TA |
phy | reg, ð->mii_data);
- /*
- * wait for the related interrupt
- */
+ /* wait for the related interrupt */
start = get_timer(0);
while (!(readl(ð->ievent) & FEC_IEVENT_MII)) {
if (get_timer(start) > (CONFIG_SYS_HZ / 1000)) {
@@ -113,17 +110,13 @@ static int fec_mdio_read(struct ethernet_regs *eth, uint8_t phyAddr,
}
}
- /*
- * clear mii interrupt bit
- */
+ /* clear mii interrupt bit */
writel(FEC_IEVENT_MII, ð->ievent);
- /*
- * it's now safe to read the PHY's register
- */
+ /* it's now safe to read the PHY's register */
val = (unsigned short)readl(ð->mii_data);
- debug("%s: phy: %02x reg:%02x val:%#x\n", __func__, phyAddr,
- regAddr, val);
+ debug("%s: phy: %02x reg:%02x val:%#x\n", __func__, phyaddr,
+ regaddr, val);
return val;
}
@@ -154,22 +147,20 @@ static void fec_mii_setspeed(struct ethernet_regs *eth)
debug("%s: mii_speed %08x\n", __func__, readl(ð->mii_speed));
}
-static int fec_mdio_write(struct ethernet_regs *eth, uint8_t phyAddr,
- uint8_t regAddr, uint16_t data)
+static int fec_mdio_write(struct ethernet_regs *eth, uint8_t phyaddr,
+ uint8_t regaddr, uint16_t data)
{
uint32_t reg; /* convenient holder for the PHY register */
uint32_t phy; /* convenient holder for the PHY */
uint32_t start;
- reg = regAddr << FEC_MII_DATA_RA_SHIFT;
- phy = phyAddr << FEC_MII_DATA_PA_SHIFT;
+ reg = regaddr << FEC_MII_DATA_RA_SHIFT;
+ phy = phyaddr << FEC_MII_DATA_PA_SHIFT;
writel(FEC_MII_DATA_ST | FEC_MII_DATA_OP_WR |
FEC_MII_DATA_TA | phy | reg | data, ð->mii_data);
- /*
- * wait for the MII interrupt
- */
+ /* wait for the MII interrupt */
start = get_timer(0);
while (!(readl(ð->ievent) & FEC_IEVENT_MII)) {
if (get_timer(start) > (CONFIG_SYS_HZ / 1000)) {
@@ -178,26 +169,24 @@ static int fec_mdio_write(struct ethernet_regs *eth, uint8_t phyAddr,
}
}
- /*
- * clear MII interrupt bit
- */
+ /* clear MII interrupt bit */
writel(FEC_IEVENT_MII, ð->ievent);
- debug("%s: phy: %02x reg:%02x val:%#x\n", __func__, phyAddr,
- regAddr, data);
+ debug("%s: phy: %02x reg:%02x val:%#x\n", __func__, phyaddr,
+ regaddr, data);
return 0;
}
-static int fec_phy_read(struct mii_dev *bus, int phyAddr, int dev_addr,
- int regAddr)
+static int fec_phy_read(struct mii_dev *bus, int phyaddr, int dev_addr,
+ int regaddr)
{
- return fec_mdio_read(bus->priv, phyAddr, regAddr);
+ return fec_mdio_read(bus->priv, phyaddr, regaddr);
}
-static int fec_phy_write(struct mii_dev *bus, int phyAddr, int dev_addr,
- int regAddr, u16 data)
+static int fec_phy_write(struct mii_dev *bus, int phyaddr, int dev_addr,
+ int regaddr, u16 data)
{
- return fec_mdio_write(bus->priv, phyAddr, regAddr, data);
+ return fec_mdio_write(bus->priv, phyaddr, regaddr, data);
}
#ifndef CONFIG_PHYLIB
@@ -218,14 +207,12 @@ static int miiphy_restart_aneg(struct eth_device *dev)
fec_mdio_write(eth, fec->phy_id, MII_BMCR, BMCR_RESET);
udelay(1000);
- /*
- * Set the auto-negotiation advertisement register bits
- */
+ /* Set the auto-negotiation advertisement register bits */
fec_mdio_write(eth, fec->phy_id, MII_ADVERTISE,
- LPA_100FULL | LPA_100HALF | LPA_10FULL |
- LPA_10HALF | PHY_ANLPAR_PSB_802_3);
+ LPA_100FULL | LPA_100HALF | LPA_10FULL |
+ LPA_10HALF | PHY_ANLPAR_PSB_802_3);
fec_mdio_write(eth, fec->phy_id, MII_BMCR,
- BMCR_ANENABLE | BMCR_ANRESTART);
+ BMCR_ANENABLE | BMCR_ANRESTART);
if (fec->mii_postcall)
ret = fec->mii_postcall(fec->phy_id);
@@ -242,9 +229,7 @@ static int miiphy_wait_aneg(struct eth_device *dev)
struct fec_priv *fec = (struct fec_priv *)dev->priv;
struct ethernet_regs *eth = fec->bus->priv;
- /*
- * Wait for AN completion
- */
+ /* Wait for AN completion */
start = get_timer(0);
do {
if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
@@ -255,7 +240,7 @@ static int miiphy_wait_aneg(struct eth_device *dev)
status = fec_mdio_read(eth, fec->phy_id, MII_BMSR);
if (status < 0) {
printf("%s: Autonegotiation failed. status: %d\n",
- dev->name, status);
+ dev->name, status);
return -1;
}
} while (!(status & BMSR_LSTATUS));
@@ -352,15 +337,15 @@ static void fec_tbd_init(struct fec_priv *fec)
/**
* Mark the given read buffer descriptor as free
* @param[in] last 1 if this is the last buffer descriptor in the chain, else 0
- * @param[in] pRbd buffer descriptor to mark free again
+ * @param[in] prbd buffer descriptor to mark free again
*/
-static void fec_rbd_clean(int last, struct fec_bd *pRbd)
+static void fec_rbd_clean(int last, struct fec_bd *prbd)
{
unsigned short flags = FEC_RBD_EMPTY;
if (last)
flags |= FEC_RBD_WRAP;
- writew(flags, &pRbd->status);
- writew(0, &pRbd->data_length);
+ writew(flags, &prbd->status);
+ writew(0, &prbd->data_length);
}
static int fec_get_hwaddr(int dev_id, unsigned char *mac)
@@ -376,37 +361,26 @@ static int _fec_set_hwaddr(struct fec_priv *fec, uchar *mac)
writel(0, &fec->eth->gaddr1);
writel(0, &fec->eth->gaddr2);
- /*
- * Set physical address
- */
+ /* Set physical address */
writel((mac[0] << 24) + (mac[1] << 16) + (mac[2] << 8) + mac[3],
- &fec->eth->paddr1);
+ &fec->eth->paddr1);
writel((mac[4] << 24) + (mac[5] << 16) + 0x8808, &fec->eth->paddr2);
return 0;
}
-/*
- * Do initial configuration of the FEC registers
- */
+/* Do initial configuration of the FEC registers */
static void fec_reg_setup(struct fec_priv *fec)
{
uint32_t rcntrl;
- /*
- * Set interrupt mask register
- */
+ /* Set interrupt mask register */
writel(0x00000000, &fec->eth->imask);
- /*
- * Clear FEC-Lite interrupt event register(IEVENT)
- */
+ /* Clear FEC-Lite interrupt event register(IEVENT) */
writel(0xffffffff, &fec->eth->ievent);
-
- /*
- * Set FEC-Lite receive control register(R_CNTRL):
- */
+ /* Set FEC-Lite receive control register(R_CNTRL): */
/* Start with frame length = 1518, common for all modes. */
rcntrl = PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT;
@@ -449,22 +423,19 @@ static int fec_open(struct fec_priv *fec)
#ifdef FEC_QUIRK_ENET_MAC
/* Enable ENET HW endian SWAP */
writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_DBSWAP,
- &fec->eth->ecntrl);
+ &fec->eth->ecntrl);
/* Enable ENET store and forward mode */
writel(readl(&fec->eth->x_wmrk) | FEC_X_WMRK_STRFWD,
- &fec->eth->x_wmrk);
+ &fec->eth->x_wmrk);
#endif
- /*
- * Enable FEC-Lite controller
- */
+ /* Enable FEC-Lite controller */
writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN,
- &fec->eth->ecntrl);
+ &fec->eth->ecntrl);
+
#if defined(CONFIG_MX25) || defined(CONFIG_MX53) || defined(CONFIG_MX6SL)
udelay(100);
- /*
- * setup the MII gasket for RMII mode
- */
+ /* setup the MII gasket for RMII mode */
/* disable the gasket */
writew(0, &fec->eth->miigsk_enr);
@@ -522,9 +493,7 @@ static int fec_open(struct fec_priv *fec)
#endif
debug("%s:Speed=%i\n", __func__, speed);
- /*
- * Enable SmartDMA receive task
- */
+ /* Enable SmartDMA receive task */
fec_rx_task_enable(fec);
udelay(100000);
@@ -539,9 +508,7 @@ static int _fec_init(struct fec_priv *fec, uchar *mac)
/* Initialize MAC address */
_fec_set_hwaddr(fec, mac);
- /*
- * Setup transmit descriptors, there are two in total.
- */
+ /* Setup transmit descriptors, there are two in total. */
fec_tbd_init(fec);
/* Setup receive descriptors. */
@@ -552,18 +519,14 @@ static int _fec_init(struct fec_priv *fec, uchar *mac)
if (fec->xcv_type != SEVENWIRE)
fec_mii_setspeed(fec->bus->priv);
- /*
- * Set Opcode/Pause Duration Register
- */
+ /* Set Opcode/Pause Duration Register */
writel(0x00010020, &fec->eth->op_pause); /* FIXME 0xffff0020; */
writel(0x2, &fec->eth->x_wmrk);
- /*
- * Set multicast address filter
- */
+
+ /* Set multicast address filter */
writel(0x00000000, &fec->eth->gaddr1);
writel(0x00000000, &fec->eth->gaddr2);
-
/* Do not access reserved register for i.MX6UL */
if (!is_mx6ul()) {
/* clear MIB RAM */
@@ -595,22 +558,16 @@ static void _fec_halt(struct fec_priv *fec)
{
int counter = 0xffff;
- /*
- * issue graceful stop command to the FEC transmitter if necessary
- */
+ /* issue graceful stop command to the FEC transmitter if necessary */
writel(FEC_TCNTRL_GTS | readl(&fec->eth->x_cntrl),
- &fec->eth->x_cntrl);
+ &fec->eth->x_cntrl);
debug("eth_halt: wait for stop regs\n");
- /*
- * wait for graceful stop to register
- */
+ /* wait for graceful stop to register */
while ((counter--) && (!(readl(&fec->eth->ievent) & FEC_IEVENT_GRA)))
udelay(1);
- /*
- * Disable SmartDMA tasks
- */
+ /* Disable SmartDMA tasks */
fec_tx_task_disable(fec);
fec_rx_task_disable(fec);
@@ -619,7 +576,7 @@ static void _fec_halt(struct fec_priv *fec)
* Note: this will also reset the BD index counter!
*/
writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN,
- &fec->eth->ecntrl);
+ &fec->eth->ecntrl);
fec->rbd_index = 0;
fec->tbd_index = 0;
debug("eth_halt: done\n");
@@ -712,9 +669,7 @@ static int _fec_send(struct fec_priv *fec, void *packet, int length)
*/
readl(addr + size - 4);
- /*
- * Enable SmartDMA transmit task
- */
+ /* Enable SmartDMA transmit task */
fec_tx_task_enable(fec);
/*
@@ -759,8 +714,8 @@ static int _fec_send(struct fec_priv *fec, void *packet, int length)
out:
debug("fec_send: status 0x%x index %d ret %i\n",
- readw(&fec->tbd_base[fec->tbd_index].status),
- fec->tbd_index, ret);
+ readw(&fec->tbd_base[fec->tbd_index].status),
+ fec->tbd_index, ret);
/* for next transmission use the other buffer */
if (fec->tbd_index)
fec->tbd_index = 0;
@@ -786,9 +741,7 @@ static int _fec_recv(struct fec_priv *fec, uchar *mac)
int i;
ALLOC_CACHE_ALIGN_BUFFER(uchar, buff, FEC_MAX_PKT_SIZE);
- /*
- * Check if any critical events have happened
- */
+ /* Check if any critical events have happened */
ievent = readl(&fec->eth->ievent);
writel(ievent, &fec->eth->ievent);
debug("fec_recv: ievent 0x%lx\n", ievent);
@@ -801,14 +754,14 @@ static int _fec_recv(struct fec_priv *fec, uchar *mac)
if (ievent & FEC_IEVENT_HBERR) {
/* Heartbeat error */
writel(0x00000001 | readl(&fec->eth->x_cntrl),
- &fec->eth->x_cntrl);
+ &fec->eth->x_cntrl);
}
if (ievent & FEC_IEVENT_GRA) {
/* Graceful stop complete */
if (readl(&fec->eth->x_cntrl) & 0x00000001) {
_fec_halt(fec);
writel(~0x00000001 & readl(&fec->eth->x_cntrl),
- &fec->eth->x_cntrl);
+ &fec->eth->x_cntrl);
_fec_init(fec, mac);
}
}
@@ -836,22 +789,16 @@ static int _fec_recv(struct fec_priv *fec, uchar *mac)
if (!(bd_status & FEC_RBD_EMPTY)) {
if ((bd_status & FEC_RBD_LAST) && !(bd_status & FEC_RBD_ERR) &&
- ((readw(&rbd->data_length) - 4) > 14)) {
- /*
- * Get buffer address and size
- */
+ ((readw(&rbd->data_length) - 4) > 14)) {
+ /* Get buffer address and size */
addr = readl(&rbd->data_pointer);
frame_length = readw(&rbd->data_length) - 4;
- /*
- * Invalidate data cache over the buffer
- */
+ /* Invalidate data cache over the buffer */
end = roundup(addr + frame_length, ARCH_DMA_MINALIGN);
addr &= ~(ARCH_DMA_MINALIGN - 1);
invalidate_dcache_range(addr, end);
- /*
- * Fill the buffer and pass it to upper layers
- */
+ /* Fill the buffer and pass it to upper layers */
#ifdef CONFIG_FEC_MXC_SWAP_PACKET
swap_packet((uint32_t *)addr, frame_length);
#endif
@@ -879,7 +826,7 @@ static int _fec_recv(struct fec_priv *fec, uchar *mac)
&fec->rbd_base[i]);
}
flush_dcache_range(addr,
- addr + ARCH_DMA_MINALIGN);
+ addr + ARCH_DMA_MINALIGN);
}
fec_rx_task_enable(fec);
@@ -1277,7 +1224,8 @@ static int fecmxc_probe(struct udevice *dev)
goto err_phy;
/* Reset chip. */
- writel(readl(&priv->eth->ecntrl) | FEC_ECNTRL_RESET, &priv->eth->ecntrl);
+ writel(readl(&priv->eth->ecntrl) | FEC_ECNTRL_RESET,
+ &priv->eth->ecntrl);
start = get_timer(0);
while (readl(&priv->eth->ecntrl) & FEC_ECNTRL_RESET) {
if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
index 9fc6153..43a7d7b 100644
--- a/drivers/net/fec_mxc.h
+++ b/drivers/net/fec_mxc.h
@@ -14,21 +14,14 @@
* SPDX-License-Identifier: GPL-2.0+
*/
-
#ifndef __FEC_MXC_H
#define __FEC_MXC_H
-void imx_get_mac_from_fuse(int dev_id, unsigned char *mac);
-
-/**
- * Layout description of the FEC
- */
+/* Layout description of the FEC */
struct ethernet_regs {
+ /* [10:2]addr = 00 */
-/* [10:2]addr = 00 */
-
-/* Control and status Registers (offset 000-1FF) */
-
+ /* Control and status Registers (offset 000-1FF) */
uint32_t res0[1]; /* MBAR_ETH + 0x000 */
uint32_t ievent; /* MBAR_ETH + 0x004 */
uint32_t imask; /* MBAR_ETH + 0x008 */
@@ -71,8 +64,7 @@ struct ethernet_regs {
uint32_t emrbr; /* MBAR_ETH + 0x188 */
uint32_t res12[29]; /* MBAR_ETH + 0x18C-1FC */
-/* MIB COUNTERS (Offset 200-2FF) */
-
+ /* MIB COUNTERS (Offset 200-2FF) */
uint32_t rmon_t_drop; /* MBAR_ETH + 0x200 */
uint32_t rmon_t_packets; /* MBAR_ETH + 0x204 */
uint32_t rmon_t_bc_pkt; /* MBAR_ETH + 0x208 */
@@ -174,7 +166,6 @@ struct ethernet_regs {
#define FEC_IMASKT_RL 0x00100000
#define FEC_IMASK_UN 0x00080000
-
#define FEC_RCNTRL_MAX_FL_SHIFT 16
#define FEC_RCNTRL_LOOP 0x00000001
#define FEC_RCNTRL_DRT 0x00000002
@@ -233,9 +224,7 @@ struct fec_bd {
uint32_t data_pointer; /* payload's buffer address */
};
-/**
- * Supported phy types on this platform
- */
+/* Supported phy types on this platform */
enum xceiver_type {
SEVENWIRE, /* 7-wire */
MII10, /* MII 10Mbps */
@@ -244,9 +233,7 @@ enum xceiver_type {
RGMII, /* RGMII */
};
-/**
- * @brief i.MX27-FEC private structure
- */
+/* @brief i.MX27-FEC private structure */
struct fec_priv {
struct ethernet_regs *eth; /* pointer to register'S base */
enum xceiver_type xcv_type; /* transceiver type */
@@ -270,6 +257,8 @@ struct fec_priv {
#endif
};
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac);
+
/**
* @brief Numbers of buffer descriptors for receiving
*
--
2.7.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 4/5] ARM: dts: imx6qdl-icore: Add FEC support
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
` (2 preceding siblings ...)
2016-10-19 11:23 ` [U-Boot] [PATCH v7 3/5] net: fec_mxc: Driver cleanups Jagan Teki
@ 2016-10-19 11:23 ` Jagan Teki
2016-10-19 11:23 ` [U-Boot] [PATCH v7 5/5] icorem6: Use CONFIG_DM_ETH support Jagan Teki
` (2 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Jagan Teki @ 2016-10-19 11:23 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add FEC dts support for Engicam i.CoreM6 dql modules.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6qdl-icore.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/dts/imx6qdl-icore.dtsi b/arch/arm/dts/imx6qdl-icore.dtsi
index f424cd5..a485c3e 100644
--- a/arch/arm/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/dts/imx6qdl-icore.dtsi
@@ -75,6 +75,14 @@
assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ phy-mode = "rmii";
+ status = "okay";
+};
+
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
@@ -118,6 +126,22 @@
};
&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b1
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
--
2.7.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 5/5] icorem6: Use CONFIG_DM_ETH support
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
` (3 preceding siblings ...)
2016-10-19 11:23 ` [U-Boot] [PATCH v7 4/5] ARM: dts: imx6qdl-icore: Add FEC support Jagan Teki
@ 2016-10-19 11:23 ` Jagan Teki
2016-10-20 5:59 ` [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
2016-11-14 8:26 ` Stefano Babic
6 siblings, 0 replies; 11+ messages in thread
From: Jagan Teki @ 2016-10-19 11:23 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/cpu/armv7/mx6/Kconfig | 1 +
board/engicam/icorem6/icorem6.c | 71 ------------------------------------
configs/imx6qdl_icore_mmc_defconfig | 1 -
configs/imx6qdl_icore_nand_defconfig | 1 -
4 files changed, 1 insertion(+), 73 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 762a581..8456b0e 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -100,6 +100,7 @@ config TARGET_MX6Q_ICORE
select MX6QDL
select OF_CONTROL
select DM
+ select DM_ETH
select DM_GPIO
select DM_MMC
select DM_THERMAL
diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c
index c152007..587775e 100644
--- a/board/engicam/icorem6/icorem6.c
+++ b/board/engicam/icorem6/icorem6.c
@@ -7,8 +7,6 @@
*/
#include <common.h>
-#include <miiphy.h>
-#include <netdev.h>
#include <asm/io.h>
#include <asm/gpio.h>
@@ -27,80 +25,11 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
static iomux_v3_cfg_t const uart4_pads[] = {
IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
-static iomux_v3_cfg_t const enet_pads[] = {
- IOMUX_PADS(PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL | PAD_CTL_SRE_FAST)),
- IOMUX_PADS(PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-#ifdef CONFIG_FEC_MXC
-#define ENET_PHY_RST IMX_GPIO_NR(7, 12)
-static int setup_fec(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
- s32 timeout = 100000;
- u32 reg = 0;
- int ret;
-
- /* Enable fec clock */
- setbits_le32(&ccm->CCGR1, MXC_CCM_CCGR1_ENET_MASK);
-
- /* use 50MHz */
- ret = enable_fec_anatop_clock(0, ENET_50MHZ);
- if (ret)
- return ret;
-
- /* Enable PLLs */
- reg = readl(&anatop->pll_enet);
- reg &= ~BM_ANADIG_PLL_SYS_POWERDOWN;
- writel(reg, &anatop->pll_enet);
- reg = readl(&anatop->pll_enet);
- reg |= BM_ANADIG_PLL_SYS_ENABLE;
- while (timeout--) {
- if (readl(&anatop->pll_enet) & BM_ANADIG_PLL_SYS_LOCK)
- break;
- }
- if (timeout <= 0)
- return -EIO;
- reg &= ~BM_ANADIG_PLL_SYS_BYPASS;
- writel(reg, &anatop->pll_enet);
-
- /* reset the phy */
- gpio_direction_output(ENET_PHY_RST, 0);
- udelay(10000);
- gpio_set_value(ENET_PHY_RST, 1);
-
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- int ret;
-
- SETUP_IOMUX_PADS(enet_pads);
- setup_fec();
-
- return ret = cpu_eth_init(bis);
-}
-#endif
-
#ifdef CONFIG_NAND_MXS
#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig
index 221ea7e..fbcbdc8 100644
--- a/configs/imx6qdl_icore_mmc_defconfig
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -28,7 +28,6 @@ CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_LIBFDT=y
CONFIG_FEC_MXC=y
CONFIG_MXC_UART=y
-CONFIG_NETDEVICES=y
CONFIG_IMX_THERMAL=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
diff --git a/configs/imx6qdl_icore_nand_defconfig b/configs/imx6qdl_icore_nand_defconfig
index 8ac3099..4b544fc 100644
--- a/configs/imx6qdl_icore_nand_defconfig
+++ b/configs/imx6qdl_icore_nand_defconfig
@@ -24,7 +24,6 @@ CONFIG_OF_LIBFDT=y
CONFIG_FEC_MXC=y
CONFIG_MXC_UART=y
CONFIG_NAND_MXS=y
-CONFIG_NETDEVICES=y
CONFIG_IMX_THERMAL=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
--
2.7.4
^ permalink raw reply related [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
` (4 preceding siblings ...)
2016-10-19 11:23 ` [U-Boot] [PATCH v7 5/5] icorem6: Use CONFIG_DM_ETH support Jagan Teki
@ 2016-10-20 5:59 ` Jagan Teki
2016-11-06 15:54 ` Jagan Teki
2016-11-14 8:26 ` Stefano Babic
6 siblings, 1 reply; 11+ messages in thread
From: Jagan Teki @ 2016-10-20 5:59 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Wed, Oct 19, 2016 at 4:53 PM, Jagan Teki <jteki@openedev.com> wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> This series convert fec_mxc to DM and tested both dm and
> non-dm code and it is on top of [1] with u-boot-imx/master
> branch.
>
> Changes for v7:
> - Remove fec_set_dev_name in dm probe
>
> Changes for v6:
> - Add Acked-by tags in commit message
>
> Changes for v5:
> - Add stub fec calls to minimize the #ifdef's
> - Use same func names on eth_ops
> - Remove reset_gpio in fec_mxc.h
> - Add new patches, for cleanup driver
>
> Changes for v4:
> - rebase to u-boot-imx/master
>
> Changes for v3:
> - Add ARM: dts: imx6qdl-icore: Add FEC support
> - icorem6: Use CONFIG_DM_ETH support
>
> Changes for v2:
> - Add TODO for implementing the enet reset code
>
> [1] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
>
> Jagan Teki (5):
> net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr
> net: fec_mxc: Convert into driver model
> net: fec_mxc: Driver cleanups
> ARM: dts: imx6qdl-icore: Add FEC support
> icorem6: Use CONFIG_DM_ETH support
>
> arch/arm/cpu/armv7/mx6/Kconfig | 1 +
> arch/arm/dts/imx6qdl-icore.dtsi | 24 ++
> board/engicam/icorem6/icorem6.c | 71 -----
> configs/imx6qdl_icore_mmc_defconfig | 1 -
> configs/imx6qdl_icore_nand_defconfig | 1 -
> drivers/net/fec_mxc.c | 516 +++++++++++++++++++++++------------
> drivers/net/fec_mxc.h | 31 +--
> 7 files changed, 378 insertions(+), 267 deletions(-)
Please apply this series along with [1]
[1] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 11+ messages in thread* [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM
2016-10-20 5:59 ` [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
@ 2016-11-06 15:54 ` Jagan Teki
0 siblings, 0 replies; 11+ messages in thread
From: Jagan Teki @ 2016-11-06 15:54 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Thu, Oct 20, 2016 at 11:29 AM, Jagan Teki <jagan@openedev.com> wrote:
> Hi Stefano,
>
> On Wed, Oct 19, 2016 at 4:53 PM, Jagan Teki <jteki@openedev.com> wrote:
>> From: Jagan Teki <jagan@amarulasolutions.com>
>>
>> This series convert fec_mxc to DM and tested both dm and
>> non-dm code and it is on top of [1] with u-boot-imx/master
>> branch.
>>
>> Changes for v7:
>> - Remove fec_set_dev_name in dm probe
>>
>> Changes for v6:
>> - Add Acked-by tags in commit message
>>
>> Changes for v5:
>> - Add stub fec calls to minimize the #ifdef's
>> - Use same func names on eth_ops
>> - Remove reset_gpio in fec_mxc.h
>> - Add new patches, for cleanup driver
>>
>> Changes for v4:
>> - rebase to u-boot-imx/master
>>
>> Changes for v3:
>> - Add ARM: dts: imx6qdl-icore: Add FEC support
>> - icorem6: Use CONFIG_DM_ETH support
>>
>> Changes for v2:
>> - Add TODO for implementing the enet reset code
>>
>> [1] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
>>
>> Jagan Teki (5):
>> net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr
>> net: fec_mxc: Convert into driver model
>> net: fec_mxc: Driver cleanups
>> ARM: dts: imx6qdl-icore: Add FEC support
>> icorem6: Use CONFIG_DM_ETH support
>>
>> arch/arm/cpu/armv7/mx6/Kconfig | 1 +
>> arch/arm/dts/imx6qdl-icore.dtsi | 24 ++
>> board/engicam/icorem6/icorem6.c | 71 -----
>> configs/imx6qdl_icore_mmc_defconfig | 1 -
>> configs/imx6qdl_icore_nand_defconfig | 1 -
>> drivers/net/fec_mxc.c | 516 +++++++++++++++++++++++------------
>> drivers/net/fec_mxc.h | 31 +--
>> 7 files changed, 378 insertions(+), 267 deletions(-)
>
> Please apply this series along with [1]
Can you please apply.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM
2016-10-19 11:23 [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
` (5 preceding siblings ...)
2016-10-20 5:59 ` [U-Boot] [PATCH v7 0/5] net: fec_mxc: Convert to DM Jagan Teki
@ 2016-11-14 8:26 ` Stefano Babic
6 siblings, 0 replies; 11+ messages in thread
From: Stefano Babic @ 2016-11-14 8:26 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 19/10/2016 13:23, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> This series convert fec_mxc to DM and tested both dm and
> non-dm code and it is on top of [1] with u-boot-imx/master
> branch.
>
> Changes for v7:
> - Remove fec_set_dev_name in dm probe
>
> Changes for v6:
> - Add Acked-by tags in commit message
>
> Changes for v5:
> - Add stub fec calls to minimize the #ifdef's
> - Use same func names on eth_ops
> - Remove reset_gpio in fec_mxc.h
> - Add new patches, for cleanup driver
>
> Changes for v4:
> - rebase to u-boot-imx/master
>
> Changes for v3:
> - Add ARM: dts: imx6qdl-icore: Add FEC support
> - icorem6: Use CONFIG_DM_ETH support
>
> Changes for v2:
> - Add TODO for implementing the enet reset code
>
> [1] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
>
> Jagan Teki (5):
> net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr
> net: fec_mxc: Convert into driver model
> net: fec_mxc: Driver cleanups
> ARM: dts: imx6qdl-icore: Add FEC support
> icorem6: Use CONFIG_DM_ETH support
>
> arch/arm/cpu/armv7/mx6/Kconfig | 1 +
> arch/arm/dts/imx6qdl-icore.dtsi | 24 ++
> board/engicam/icorem6/icorem6.c | 71 -----
> configs/imx6qdl_icore_mmc_defconfig | 1 -
> configs/imx6qdl_icore_nand_defconfig | 1 -
> drivers/net/fec_mxc.c | 516 +++++++++++++++++++++++------------
> drivers/net/fec_mxc.h | 31 +--
> 7 files changed, 378 insertions(+), 267 deletions(-)
>
Applied to u-boot-imx, -next branch, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 11+ messages in thread