From: Eric Nelson <eric@nelint.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [RFC PATCH 4/9] mx6memcal: add configuration for Nitrogen6_max board
Date: Tue, 1 Nov 2016 13:13:45 -0700 [thread overview]
Message-ID: <1478031230-7263-5-git-send-email-eric@nelint.com> (raw)
In-Reply-To: <1478031230-7263-1-git-send-email-eric@nelint.com>
Signed-off-by: Eric Nelson <eric@nelint.com>
---
configs/mx6memcal_nitrogen6_max_defconfig | 33 +++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
create mode 100644 configs/mx6memcal_nitrogen6_max_defconfig
diff --git a/configs/mx6memcal_nitrogen6_max_defconfig b/configs/mx6memcal_nitrogen6_max_defconfig
new file mode 100644
index 0000000..097d27d
--- /dev/null
+++ b/configs/mx6memcal_nitrogen6_max_defconfig
@@ -0,0 +1,33 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_MX6_DDRCAL=y
+CONFIG_TARGET_MX6MEMCAL=y
+CONFIG_SERIAL_CONSOLE_UART2=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6QDL"
+CONFIG_SPL=y
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_BOOTM is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_SAVEENV is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_CACHE=y
+CONFIG_REGEX=y
--
2.7.4
next prev parent reply other threads:[~2016-11-01 20:13 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-30 17:18 [U-Boot] [PATCH 0/3] mx6: ddr: updates for dynamic DDR calibration Eric Nelson
2016-10-30 17:19 ` [U-Boot] [PATCH 1/3] mx6: ddr: allow 32 cycles for DQS gating calibration Eric Nelson
2016-10-30 17:27 ` Marek Vasut
2016-10-30 17:19 ` [U-Boot] [PATCH 2/3] mx6: ddr: pass mx6_ddr_sysinfo to calibration routines Eric Nelson
2016-10-30 17:29 ` Marek Vasut
2016-10-30 17:19 ` [U-Boot] [PATCH 3/3] mx6: ddr: add routine to return DDR calibration data Eric Nelson
2016-10-30 17:30 ` Marek Vasut
2016-10-30 19:14 ` Eric Nelson
2016-10-30 20:02 ` Marek Vasut
2016-10-30 19:20 ` [U-Boot] [PATCH] ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routines Eric Nelson
2016-10-30 20:03 ` Marek Vasut
2016-10-30 23:10 ` Eric Nelson
2016-10-30 23:33 ` [U-Boot] [PATCH V2 0/4] mx6: ddr: updates for dynamic DDR calibration Eric Nelson
2016-10-30 23:33 ` [U-Boot] [PATCH V2 1/4] mx6: ddr: allow 32 cycles for DQS gating calibration Eric Nelson
2016-10-30 23:33 ` [U-Boot] [PATCH V2 2/4] mx6: ddr: pass mx6_ddr_sysinfo to calibration routines Eric Nelson
2016-10-30 23:33 ` [U-Boot] [PATCH V2 3/4] mx6: ddr: add routine to return DDR calibration data Eric Nelson
2016-10-30 23:33 ` [U-Boot] [PATCH V2 4/4] ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routines Eric Nelson
2016-11-22 10:59 ` [U-Boot] [PATCH V2 0/4] mx6: ddr: updates for dynamic DDR calibration Christoph Fritz
2016-11-29 16:28 ` Stefano Babic
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 0/9] ARM: imx: mx6: Add virtual mx6memcal board Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 1/9] mx6: Add board mx6memcal for use in validating DDR Eric Nelson
2017-07-14 14:18 ` Fabio Estevam
2017-07-14 17:58 ` Eric Nelson
2017-07-14 19:01 ` Fabio Estevam
2017-07-28 2:50 ` Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 2/9] mx6memcal: zero values for MPWRDLCTL cause read DQS calibration errors Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 3/9] mx6memcal: add configuration for SABRE Lite Eric Nelson
2016-11-01 20:13 ` Eric Nelson [this message]
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 5/9] mx6memcal: add configuration for tr1x board (i.MX6SL with DDR3) Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 6/9] mx6memcal: add configuration for Wandboard Solo (512MiB of x32 DDR3) Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 7/9] mx6memcal: add configuration for Wandboard Quad Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 8/9] mx6memcal: add configuration for mx6slevk Eric Nelson
2016-11-01 20:13 ` [U-Boot] [RFC PATCH 9/9] mx6memcal: add configuration for warp board (i.MX6SL) Eric Nelson
2016-11-02 2:06 ` [U-Boot] [RFC PATCH 0/3] ARM: imx: mx6: Add plugin support for SPL Eric Nelson
2016-11-02 2:06 ` [U-Boot] [RFC PATCH 1/3] ARM: mx6: preserve Boot ROM stack in SPL Eric Nelson
2016-11-02 2:06 ` [U-Boot] [RFC PATCH 2/3] ARM: mx6: ddr: add plugin-utils placeholder Eric Nelson
2016-11-02 2:06 ` [U-Boot] [RFC PATCH 3/3] ARM: imx: mx6memcal: allow build of combined SPL+U-Boot Eric Nelson
2017-01-18 1:27 ` [U-Boot] [RFC PATCH 0/3] ARM: imx: mx6: Add plugin support for SPL Tim Harvey
2017-01-18 17:05 ` Eric Nelson
2017-01-18 18:49 ` Tim Harvey
2017-01-18 19:01 ` Fabio Estevam
2017-01-20 17:40 ` Tim Harvey
2017-01-27 14:56 ` Fabio Estevam
2017-01-27 15:25 ` Otavio Salvador
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1478031230-7263-5-git-send-email-eric@nelint.com \
--to=eric@nelint.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox