From: Jagan Teki <jagan@openedev.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v3 05/13] ARM: dts: imx6qdl-icore: Add FEC support
Date: Tue, 6 Dec 2016 00:00:52 +0100 [thread overview]
Message-ID: <1480978860-4351-6-git-send-email-jagan@openedev.com> (raw)
In-Reply-To: <1480978860-4351-1-git-send-email-jagan@openedev.com>
From: Jagan Teki <jagan@amarulasolutions.com>
Add FEC dts support for Engicam i.CoreM6 dql modules.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6qdl-icore.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/dts/imx6qdl-icore.dtsi b/arch/arm/dts/imx6qdl-icore.dtsi
index f424cd5..a485c3e 100644
--- a/arch/arm/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/dts/imx6qdl-icore.dtsi
@@ -75,6 +75,14 @@
assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ phy-mode = "rmii";
+ status = "okay";
+};
+
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
@@ -118,6 +126,22 @@
};
&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b1
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
--
1.9.1
next prev parent reply other threads:[~2016-12-05 23:00 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-05 23:00 [U-Boot] [PATCH v3 00/13] imx6: icorem6: Add dm-eth, framebuffer and I2C support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 01/13] net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 02/13] net: fec_mxc: Convert into driver model Jagan Teki
2016-12-09 18:22 ` Joe Hershberger
2016-12-09 22:26 ` Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 03/13] net: fec_mxc: Driver cleanups Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 04/13] dm: net: fec: Add .read_rom_hwaddr Jagan Teki
2016-12-05 23:00 ` Jagan Teki [this message]
2016-12-05 23:00 ` [U-Boot] [PATCH v3 06/13] icorem6: Use CONFIG_DM_ETH support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 07/13] video: Kconfig: Add VIDEO_IPV3 entry Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 08/13] imx6: icorem6: Add framebuffer support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 09/13] imx6: icorem6: Add custom splashscreen support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 10/13] i2c: Kconfig: Add SYS_I2C_MXC entry Jagan Teki
2016-12-06 14:06 ` Heiko Schocher
2016-12-06 15:45 ` Jagan Teki
2016-12-06 14:47 ` Fabio Estevam
2016-12-06 15:44 ` Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 11/13] i2c: mxc: Print hex instead of decimal for bus address Jagan Teki
2016-12-06 14:07 ` Heiko Schocher
2016-12-05 23:00 ` [U-Boot] [PATCH v3 12/13] i2c: mxc: Make 'no gpio pinctrl state' print as debug Jagan Teki
2016-12-06 14:08 ` Heiko Schocher
2016-12-05 23:01 ` [U-Boot] [PATCH v3 13/13] imx6: icorem6: Add I2C support Jagan Teki
2016-12-06 14:10 ` Heiko Schocher
2016-12-06 17:25 ` Jagan Teki
2016-12-07 16:01 ` [U-Boot] [PATCH v3 00/13] imx6: icorem6: Add dm-eth, framebuffer and " Jagan Teki
2016-12-13 12:36 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1480978860-4351-6-git-send-email-jagan@openedev.com \
--to=jagan@openedev.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox