[U-Boot] [PATCH v4 06/28] arm: socfpga: arria10: add socfpga_arria10_socdk config

[Dalon Westergreen <dwesterg@gmail.com>]

On Fri, 2017-02-17 at 22:12 +0100, Marek Vasut wrote:
> On 02/17/2017 11:18 AM, Ley Foon Tan wrote:
> > 
> > On Mon, Jan 23, 2017 at 11:46 AM, Marek Vasut <marex@denx.de> wrote:
> > > 
> > > On 01/10/2017 06:20 AM, Chee Tien Fong wrote:
> > > > 
> > > > From: Tien Fong Chee <tien.fong.chee@intel.com>
> > > > 
> > > > Add config for the Arria10 SoC Development Kit.
> > > > 
> > > > Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
> > > > Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
> > > > Acked-by: Marek Vasut <marex@denx.de>
> > > > Cc: Marek Vasut <marex@denx.de>
> > > > Cc: Dinh Nguyen <dinguyen@kernel.org>
> > > > Cc: Chin Liang See <chin.liang.see@intel.com>
> > > > Cc: Tien Fong <skywindctf@gmail.com>
> > > > ---
> > > > ?include/configs/socfpga_arria10_socdk.h | 94
> > > > +++++++++++++++++++++++++++++++++
> > > > ?1 file changed, 94 insertions(+)
> > > > ?create mode 100644 include/configs/socfpga_arria10_socdk.h
> > > > 
> > > > diff --git a/include/configs/socfpga_arria10_socdk.h
> > > > b/include/configs/socfpga_arria10_socdk.h
> > > > new file mode 100644
> > > > index 0000000..577f60f
> > > > --- /dev/null
> > > > +++ b/include/configs/socfpga_arria10_socdk.h
> > > > @@ -0,0 +1,94 @@
> > > > +/*
> > > > + *??Copyright (C) 2015 Altera Corporation <www.altera.com>
> > > 
> > > 2017 ... fix globally.
> > Okay
> > > 
> > > 
> > > > 
> > > > + * SPDX-License-Identifier:??GPL-2.0
> > > > + */
> > > > +
> > > > +#ifndef __CONFIG_SOCFGPA_ARRIA10_H__
> > > > +#define __CONFIG_SOCFGPA_ARRIA10_H__
> > > > +
> > > > +#include <asm/arch/base_addr_a10.h>
> > > > +/* U-Boot Commands */
> > > > +#define CONFIG_SYS_NO_FLASH
> > > > +#define CONFIG_DOS_PARTITION
> > > > +#define CONFIG_FAT_WRITE
> > > > +#define CONFIG_HW_WATCHDOG
> > > > +
> > > > +#define CONFIG_CMD_ASKENV
> > > > +#define CONFIG_CMD_BOOTZ
> > > > +#define CONFIG_CMD_CACHE
> > > > +#define CONFIG_CMD_DHCP
> > > > +#define CONFIG_CMD_EXT4
> > > > +#define CONFIG_CMD_EXT4_WRITE
> > > > +#define CONFIG_CMD_FAT
> > > > +#define CONFIG_CMD_FS_GENERIC
> > > > +#define CONFIG_CMD_GREPENV
> > > > +#define CONFIG_CMD_MMC
> > > > +#define CONFIG_CMD_PING
> > > 
> > > A lot of this stuff was converted to Kconfig, please recheck.
> > Okay, will update this.
> > > 
> > > 
> > > > 
> > > > +/*
> > > > + * Memory configurations
> > > > + */
> > > > +#define PHYS_SDRAM_1_SIZE????????????0x2000000
> > > > +
> > > > +/* Booting Linux */
> > > > +#define CONFIG_BOOTDELAY?????3
> > > > +#define CONFIG_BOOTFILE??????????????"zImage"
> > > > +#define CONFIG_BOOTARGS??????????????"console=ttyS0,"
> > > > __stringify(CONFIG_BAUDRATE)
> > > > +#define CONFIG_BOOTCOMMAND??????"run mmcload; run mmcboot"
> > > > +#define CONFIG_LOADADDR??????????????0x01000000
> > > > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> > > > +
> > > > +/*
> > > > + * Display CPU and Board Info
> > > > + */
> > > > +#define CONFIG_DISPLAY_CPUINFO
> > > > +#define CONFIG_DISPLAY_BOARDINFO
> > > > +#define CONFIG_DISPLAY_BOARDINFO_LATE
> > > > +
> > > > +/* Ethernet on SoC (EMAC) */
> > > > +#if defined(CONFIG_CMD_NET)
> > > > +
> > > > +/* PHY */
> > > > +#define CONFIG_PHY_MICREL
> > > > +#define CONFIG_PHY_MICREL_KSZ9031
> > > > +
> > > > +#endif
> > > > +
> > > > +#define CONFIG_ENV_IS_IN_MMC
> > > > +#define CONFIG_SYS_MMC_ENV_DEV???????????????0/* device 0 */
> > > > +#define CONFIG_ENV_OFFSET????????????512/* just after the MBR */
> > > > +
> > > > +/*
> > > > + * arguments passed to the bootz command. The value of
> > > > + * CONFIG_BOOTARGS goes into the environment value "bootargs".
> > > > + * Do note the value will overide also the chosen node in FDT blob.
> > > > + */
> > > > +#define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE)
> > > > +
> > > > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > > > +?????"verify=n\0" \
> > > > +?????"loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
> > > > +?????"ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
> > > > +?????????????"bootm ${loadaddr} - ${fdt_addr}\0" \
> > > > +?????"bootimage=zImage\0" \
> > > > +?????"fdt_addr=100\0" \
> > > > +?????"fdtimage=socfpga.dtb\0" \
> > > > +?????????????"fsloadcmd=ext2load\0" \
> > > > +?????"bootm ${loadaddr} - ${fdt_addr}\0" \
> > > > +?????"mmcroot=/dev/mmcblk0p2\0" \
> > > > +?????"mmcboot=setenv bootargs " CONFIG_BOOTARGS \
> > > > +?????????????" root=${mmcroot} rw rootwait;" \
> > > > +?????????????"bootz ${loadaddr} - ${fdt_addr}\0" \
> > > > +?????"mmcload=mmc rescan;" \
> > > > +?????????????"load mmc 0:1 ${loadaddr} ${bootimage};" \
> > > > +?????????????"load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
> > > > +?????"qspiroot=/dev/mtdblock0\0" \
> > > > +?????"qspirootfstype=jffs2\0" \
> > > > +?????"qspiboot=setenv bootargs " CONFIG_BOOTARGS \
> > > > +?????????????" root=${qspiroot} rw rootfstype=${qspirootfstype};"\
> > > > +?????????????"bootm ${loadaddr} - ${fdt_addr}\0"
> > > 
> > > Take a look at:
> > > [PATCH v2 0/7] arm: socfpga: update socfpga environments
> > > and adjust accordingly.
> > I checked this patch series, it is in v8 and it hasn't integrate to
> > mainline yet.
> > I will working my patches on top of this patch series, is it okay?
> 
> It's fine. Dalon, what's the status here ?

Frankly, i would just ignore that patch set. i will submit a new
one that just moves directly to distro boot. ?sorry for the fuss.

--dalon

> 
>