[U-Boot] [PATCH 1/1] Add support Raspberry-Pi Ziro W

[Dmitry Korunov <dessel.k@gmail.com>]

Signed-off-by: Dmitry Korunov <dessel.k@gmail.com>
---
 arch/arm/dts/bcm2835-rpi-zero-w.dts    | 44 ++++++++++++++++++++++++++++++++++
 arch/arm/dts/bcm283x-rpi-usb-host.dtsi |  3 +++
 arch/arm/mach-bcm283x/Kconfig          | 16 +++++++++++++
 board/raspberrypi/rpi/rpi.c            |  5 ++++
 configs/rpi_0_w_defconfig              | 28 ++++++++++++++++++++++
 include/configs/rpi.h                  |  2 +-
 6 files changed, 97 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/bcm2835-rpi-zero-w.dts
 create mode 100644 arch/arm/dts/bcm283x-rpi-usb-host.dtsi
 create mode 100644 configs/rpi_0_w_defconfig

diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts
new file mode 100644
index 0000000..c63937d
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-zero-w.dts
@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+	model = "Raspberry Pi Zero W";
+
+	leds {
+		act {
+			gpios = <&gpio 47 0>;
+		};
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi
new file mode 100644
index 0000000..73f4ece
--- /dev/null
+++ b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi
@@ -0,0 +1,3 @@
+&usb {
+	dr_mode = "host";
+};
diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig
index 69f7a46..86453c1 100644
--- a/arch/arm/mach-bcm283x/Kconfig
+++ b/arch/arm/mach-bcm283x/Kconfig
@@ -44,6 +44,22 @@ config TARGET_RPI
 	  This option creates a build targetting the ARM1176 ISA.
 	select BCM2835
 
+config TARGET_RPI_0_W
+	bool "Raspberry Pi Ziro  W"
+	help
+	  Support for all ARM1176-/BCM2835-based Raspberry Pi variants, such as
+	  the RPi Zero model W.
+
+	  This option assumes the VideoCore firmware is configured to use the
+	  mini UART (rather than PL011) for the serial console. This is the
+	  default on the RPi Zero W. To enable the UART console, the following
+	  non-default option must be present in config.txt: enable_uart=1.
+	  This is required for U-Boot to operate correctly, even if you only
+	  care about the HDMI/usbkbd console.
+
+	  This option creates a build targetting the ARMv7/AArch32 ISA.
+	select BCM2835
+
 config TARGET_RPI_2
 	bool "Raspberry Pi 2"
 	help
diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c
index d3c6ba5..e59d358 100644
--- a/board/raspberrypi/rpi/rpi.c
+++ b/board/raspberrypi/rpi/rpi.c
@@ -105,6 +105,11 @@ static const struct rpi_model rpi_models_new_scheme[] = {
 		DTB_DIR "bcm2835-rpi-zero.dtb",
 		false,
 	},
+	[0xC] = {
+		"Zero W",
+		DTB_DIR "bcm2835-rpi-zero-w.dtb",
+		false,
+	},
 };
 
 static const struct rpi_model rpi_models_old_scheme[] = {
diff --git a/configs/rpi_0_w_defconfig b/configs/rpi_0_w_defconfig
new file mode 100644
index 0000000..092f378
--- /dev/null
+++ b/configs/rpi_0_w_defconfig
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_ARCH_BCM283X=y
+CONFIG_TARGET_RPI_0_W=y
+CONFIG_DEFAULT_DEVICE_TREE="bcm2835-rpi-zero-w"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SYS_PROMPT="U-Boot> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_BCM2835=y
+CONFIG_DM_ETH=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_CONSOLE_SCROLL_LINES=10
+CONFIG_PHYS_TO_BUS=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/include/configs/rpi.h b/include/configs/rpi.h
index d715eaa..0ead8d7 100644
--- a/include/configs/rpi.h
+++ b/include/configs/rpi.h
@@ -80,7 +80,7 @@
 #endif
 
 /* Console UART */
-#ifdef CONFIG_BCM2837
+#if  defined (CONFIG_BCM2837) || defined(CONFIG_TARGET_RPI_0_W)
 #define CONFIG_BCM283X_MU_SERIAL
 #else
 #define CONFIG_PL01X_SERIAL
-- 
2.7.4