* [U-Boot] [PATCH v2 1/2] ARC: HSDK: add platform-specific commands
2018-03-26 12:57 [U-Boot] [PATCH v2 0/2] ARC: HSDK: add platform-specific stuff Eugeniy Paltsev
@ 2018-03-26 12:57 ` Eugeniy Paltsev
2018-03-30 20:08 ` Alexey Brodkin
2018-03-26 12:57 ` [U-Boot] [PATCH v2 2/2] ARC: HSDK: enable spi flash support Eugeniy Paltsev
1 sibling, 1 reply; 7+ messages in thread
From: Eugeniy Paltsev @ 2018-03-26 12:57 UTC (permalink / raw)
To: u-boot
This patch add support of hsdk platform-specific commands:
hsdk_clock set - set clock from axi_freq, cpu_freq and tun_freq
environment variables/command line arguments
hsdk_clock get - save clock frequencies to axi_freq, cpu_freq
and tun_freq environment variables
hsdk_clock print - show CPU, AXI, DDR and TUNNEL current
clock frequencies.
hsdk_clock print_all - show all currently used clock frequencies.
hsdk_init - setup board HW in one of pre-defined configuration
(hsdk_hs34 / hsdk_hs36 / hsdk_hs36_ccm / hsdk_hs38 /
hsdk_hs38_ccm / hsdk_hs38x2 / hsdk_hs38x3 / hsdk_hs38x4)
hsdk_go - run baremetal application on hsdk configured
by hsdk_init command.
This patch changes default behaviour of 'bootm' command:
now we are able to set number of CPUs to be kicked by setting
'core_mask' environment variable before 'bootm' command run.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
---
arch/arc/dts/hsdk.dts | 30 ++
board/synopsys/hsdk/MAINTAINERS | 4 +-
board/synopsys/hsdk/Makefile | 2 +
board/synopsys/hsdk/clk-lib.c | 75 +++
board/synopsys/hsdk/clk-lib.h | 38 ++
board/synopsys/hsdk/env-lib.c | 302 +++++++++++
board/synopsys/hsdk/env-lib.h | 58 +++
board/synopsys/hsdk/hsdk.c | 1046 +++++++++++++++++++++++++++++++++++++--
configs/hsdk_defconfig | 4 +
include/configs/hsdk.h | 56 ++-
10 files changed, 1564 insertions(+), 51 deletions(-)
create mode 100644 board/synopsys/hsdk/clk-lib.c
create mode 100644 board/synopsys/hsdk/clk-lib.h
create mode 100644 board/synopsys/hsdk/env-lib.c
create mode 100644 board/synopsys/hsdk/env-lib.h
diff --git a/arch/arc/dts/hsdk.dts b/arch/arc/dts/hsdk.dts
index 67dfb93ca8..09f3fe9a37 100644
--- a/arch/arc/dts/hsdk.dts
+++ b/arch/arc/dts/hsdk.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "skeleton.dtsi"
+#include "dt-bindings/clock/snps,hsdk-cgu.h"
/ {
#address-cells = <1>;
@@ -24,6 +25,35 @@
};
};
+ clk-fmeas {
+ clocks = <&cgu_clk CLK_ARC_PLL>, <&cgu_clk CLK_SYS_PLL>,
+ <&cgu_clk CLK_TUN_PLL>, <&cgu_clk CLK_DDR_PLL>,
+ <&cgu_clk CLK_ARC>, <&cgu_clk CLK_HDMI_PLL>,
+ <&cgu_clk CLK_TUN_TUN>, <&cgu_clk CLK_HDMI>,
+ <&cgu_clk CLK_SYS_APB>, <&cgu_clk CLK_SYS_AXI>,
+ <&cgu_clk CLK_SYS_ETH>, <&cgu_clk CLK_SYS_USB>,
+ <&cgu_clk CLK_SYS_SDIO>, <&cgu_clk CLK_SYS_HDMI>,
+ <&cgu_clk CLK_SYS_GFX_CORE>, <&cgu_clk CLK_SYS_GFX_DMA>,
+ <&cgu_clk CLK_SYS_GFX_CFG>, <&cgu_clk CLK_SYS_DMAC_CORE>,
+ <&cgu_clk CLK_SYS_DMAC_CFG>, <&cgu_clk CLK_SYS_SDIO_REF>,
+ <&cgu_clk CLK_SYS_SPI_REF>, <&cgu_clk CLK_SYS_I2C_REF>,
+ <&cgu_clk CLK_SYS_UART_REF>, <&cgu_clk CLK_SYS_EBI_REF>,
+ <&cgu_clk CLK_TUN_ROM>, <&cgu_clk CLK_TUN_PWM>;
+ clock-names = "cpu-pll", "sys-pll",
+ "tun-pll", "ddr-clk",
+ "cpu-clk", "hdmi-pll",
+ "tun-clk", "hdmi-clk",
+ "apb-clk", "axi-clk",
+ "eth-clk", "usb-clk",
+ "sdio-clk", "hdmi-sys-clk",
+ "gfx-core-clk", "gfx-dma-clk",
+ "gfx-cfg-clk", "dmac-core-clk",
+ "dmac-cfg-clk", "sdio-ref-clk",
+ "spi-clk", "i2c-clk",
+ "uart-clk", "ebi-clk",
+ "rom-clk", "pwm-clk";
+ };
+
cgu_clk: cgu-clk at f0000000 {
compatible = "snps,hsdk-cgu-clock";
reg = <0xf0000000 0x10>, <0xf00014B8 0x4>;
diff --git a/board/synopsys/hsdk/MAINTAINERS b/board/synopsys/hsdk/MAINTAINERS
index d034bc479d..e22bd1e40b 100644
--- a/board/synopsys/hsdk/MAINTAINERS
+++ b/board/synopsys/hsdk/MAINTAINERS
@@ -1,5 +1,5 @@
-AXS10X BOARD
-M: Alexey Brodkin <abrodkin@synopsys.com>
+HSDK BOARD
+M: Eugeniy Paltsev <paltsev@synopsys.com>
S: Maintained
F: board/synopsys/hsdk/
F: configs/hsdk_defconfig
diff --git a/board/synopsys/hsdk/Makefile b/board/synopsys/hsdk/Makefile
index d84dd03265..7ecff3d740 100644
--- a/board/synopsys/hsdk/Makefile
+++ b/board/synopsys/hsdk/Makefile
@@ -5,3 +5,5 @@
#
obj-y += hsdk.o
+obj-y += env-lib.o
+obj-y += clk-lib.o
diff --git a/board/synopsys/hsdk/clk-lib.c b/board/synopsys/hsdk/clk-lib.c
new file mode 100644
index 0000000000..1ce54afffe
--- /dev/null
+++ b/board/synopsys/hsdk/clk-lib.c
@@ -0,0 +1,75 @@
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ * Author: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <clk.h>
+#include <dm/device.h>
+
+#include "clk-lib.h"
+
+#define HZ_IN_MHZ 1000000
+#define ceil(x, y) ({ ulong __x = (x), __y = (y); (__x + __y - 1) / __y; })
+
+int soc_clk_ctl(const char *name, ulong *rate, enum clk_ctl_ops ctl)
+{
+ int ret;
+ ulong mhz_rate, priv_rate;
+ struct clk clk;
+
+ /* Dummy fmeas device, just to be able to use standard clk_* api */
+ struct udevice fmeas = {
+ .name = "clk-fmeas",
+ .node = ofnode_path("/clk-fmeas"),
+ };
+
+ ret = clk_get_by_name(&fmeas, name, &clk);
+ if (ret) {
+ pr_err("clock '%s' not found, err=%d\n", name, ret);
+ return ret;
+ }
+
+ if (ctl & CLK_ON) {
+ ret = clk_enable(&clk);
+ if (ret && ret != -ENOSYS && ret != -ENOTSUPP)
+ return ret;
+ }
+
+ if ((ctl & CLK_SET) && rate) {
+ priv_rate = ctl & CLK_MHZ ? (*rate) * HZ_IN_MHZ : *rate;
+ ret = clk_set_rate(&clk, priv_rate);
+ if (ret)
+ return ret;
+ }
+
+ if (ctl & CLK_OFF) {
+ ret = clk_disable(&clk);
+ if (ret) {
+ pr_err("clock '%s' can't be disabled, err=%d\n", name, ret);
+ return ret;
+ }
+ }
+
+ priv_rate = clk_get_rate(&clk);
+
+ clk_free(&clk);
+
+ mhz_rate = ceil(priv_rate, HZ_IN_MHZ);
+
+ if (ctl & CLK_MHZ)
+ priv_rate = mhz_rate;
+
+ if ((ctl & CLK_GET) && rate)
+ *rate = priv_rate;
+
+ if ((ctl & CLK_PRINT) && (ctl & CLK_MHZ))
+ printf("HSDK: clock '%s' rate %lu MHz\n", name, priv_rate);
+ else if (ctl & CLK_PRINT)
+ printf("HSDK: clock '%s' rate %lu Hz\n", name, priv_rate);
+ else
+ debug("HSDK: clock '%s' rate %lu MHz\n", name, mhz_rate);
+
+ return 0;
+}
diff --git a/board/synopsys/hsdk/clk-lib.h b/board/synopsys/hsdk/clk-lib.h
new file mode 100644
index 0000000000..3b7dbc58ae
--- /dev/null
+++ b/board/synopsys/hsdk/clk-lib.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ * Author: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __BOARD_CLK_LIB_H
+#define __BOARD_CLK_LIB_H
+
+#include <common.h>
+
+enum clk_ctl_ops {
+ CLK_SET = BIT(0), /* set frequency */
+ CLK_GET = BIT(1), /* get frequency */
+ CLK_ON = BIT(2), /* enable clock */
+ CLK_OFF = BIT(3), /* disable clock */
+ CLK_PRINT = BIT(4), /* print frequency */
+ CLK_MHZ = BIT(5) /* all values in MHZ instead of HZ */
+};
+
+/*
+ * Depending on the clk_ctl_ops enable / disable /
+ * set clock rate from 'rate' argument / read clock to 'rate' argument /
+ * print clock rate. If CLK_MHZ flag set in clk_ctl_ops 'rate' is in MHz,
+ * otherwise - in Hz.
+ *
+ * This function expects "clk-fmeas" node in device tree:
+ * / {
+ * clk-fmeas {
+ * clocks = <&cpu_pll>, <&sys_pll>;
+ * clock-names = "cpu-pll", "sys-pll";
+ * };
+ * };
+ */
+int soc_clk_ctl(const char *name, ulong *rate, enum clk_ctl_ops ctl);
+
+#endif /* __BOARD_CLK_LIB_H */
diff --git a/board/synopsys/hsdk/env-lib.c b/board/synopsys/hsdk/env-lib.c
new file mode 100644
index 0000000000..6b53d92c23
--- /dev/null
+++ b/board/synopsys/hsdk/env-lib.c
@@ -0,0 +1,302 @@
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ * Author: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include "env-lib.h"
+
+#define MAX_CMD_LEN 25
+
+static void env_clear_common(u32 index, const struct env_map_common *map)
+{
+ map[index].val->val = 0;
+ map[index].val->set = false;
+}
+
+static int env_read_common(u32 index, const struct env_map_common *map)
+{
+ u32 val;
+
+ if (!env_get_yesno(map[index].env_name)) {
+ if (map[index].type == ENV_HEX) {
+ val = (u32)env_get_hex(map[index].env_name, 0);
+ debug("ENV: %s: = %#x\n", map[index].env_name, val);
+ } else {
+ val = (u32)env_get_ulong(map[index].env_name, 10, 0);
+ debug("ENV: %s: = %d\n", map[index].env_name, val);
+ }
+
+ map[index].val->val = val;
+ map[index].val->set = true;
+ }
+
+ return 0;
+}
+
+static void env_clear_core(u32 index, const struct env_map_percpu *map)
+{
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ (*map[index].val)[i].val = 0;
+ (*map[index].val)[i].set = false;
+ }
+}
+
+static int env_read_core(u32 index, const struct env_map_percpu *map)
+{
+ u32 val;
+ char command[MAX_CMD_LEN];
+
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ sprintf(command, "%s_%u", map[index].env_name, i);
+ if (!env_get_yesno(command)) {
+ if (map[index].type == ENV_HEX) {
+ val = (u32)env_get_hex(command, 0);
+ debug("ENV: %s: = %#x\n", command, val);
+ } else {
+ val = (u32)env_get_ulong(command, 10, 0);
+ debug("ENV: %s: = %d\n", command, val);
+ }
+
+ (*map[index].val)[i].val = val;
+ (*map[index].val)[i].set = true;
+ }
+ }
+
+ return 0;
+}
+
+static int env_validate_common(u32 index, const struct env_map_common *map)
+{
+ u32 value = map[index].val->val;
+ bool set = map[index].val->set;
+ u32 min = map[index].min;
+ u32 max = map[index].max;
+
+ /* Check if environment is mandatory */
+ if (map[index].mandatory && !set) {
+ pr_err("Variable \'%s\' is mandatory, but it is not defined\n",
+ map[index].env_name);
+
+ return -EINVAL;
+ }
+
+ /* Check environment boundary */
+ if (set && (value < min || value > max)) {
+ if (map[index].type == ENV_HEX)
+ pr_err("Variable \'%s\' must be between %#x and %#x\n",
+ map[index].env_name, min, max);
+ else
+ pr_err("Variable \'%s\' must be between %u and %u\n",
+ map[index].env_name, min, max);
+
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int env_validate_core(u32 index, const struct env_map_percpu *map,
+ bool (*cpu_used)(u32))
+{
+ u32 value;
+ bool set;
+ bool mandatory = map[index].mandatory;
+ u32 min, max;
+
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ set = (*map[index].val)[i].set;
+ value = (*map[index].val)[i].val;
+
+ /* Check if environment is mandatory */
+ if (cpu_used(i) && mandatory && !set) {
+ pr_err("CPU %u is used, but \'%s_%u\' is not defined\n",
+ i, map[index].env_name, i);
+
+ return -EINVAL;
+ }
+
+ min = map[index].min[i];
+ max = map[index].max[i];
+
+ /* Check environment boundary */
+ if (set && (value < min || value > max)) {
+ if (map[index].type == ENV_HEX)
+ pr_err("Variable \'%s_%u\' must be between %#x and %#x\n",
+ map[index].env_name, i, min, max);
+ else
+ pr_err("Variable \'%s_%u\' must be between %d and %d\n",
+ map[index].env_name, i, min, max);
+
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+void envs_cleanup_core(const struct env_map_percpu *map)
+{
+ /* Cleanup env struct first */
+ for (u32 i = 0; map[i].env_name; i++)
+ env_clear_core(i, map);
+}
+
+void envs_cleanup_common(const struct env_map_common *map)
+{
+ /* Cleanup env struct first */
+ for (u32 i = 0; map[i].env_name; i++)
+ env_clear_common(i, map);
+}
+
+int envs_read_common(const struct env_map_common *map)
+{
+ int ret;
+
+ for (u32 i = 0; map[i].env_name; i++) {
+ ret = env_read_common(i, map);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+int envs_validate_common(const struct env_map_common *map)
+{
+ int ret;
+
+ for (u32 i = 0; map[i].env_name; i++) {
+ ret = env_validate_common(i, map);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+int envs_read_validate_common(const struct env_map_common *map)
+{
+ int ret;
+
+ envs_cleanup_common(map);
+
+ ret = envs_read_common(map);
+ if (ret)
+ return ret;
+
+ ret = envs_validate_common(map);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+int envs_read_validate_core(const struct env_map_percpu *map,
+ bool (*cpu_used)(u32))
+{
+ int ret;
+
+ envs_cleanup_core(map);
+
+ for (u32 i = 0; map[i].env_name; i++) {
+ ret = env_read_core(i, map);
+ if (ret)
+ return ret;
+ }
+
+ for (u32 i = 0; map[i].env_name; i++) {
+ ret = env_validate_core(i, map, cpu_used);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+int envs_process_and_validate(const struct env_map_common *common,
+ const struct env_map_percpu *core,
+ bool (*cpu_used)(u32))
+{
+ int ret;
+
+ ret = envs_read_validate_common(common);
+ if (ret)
+ return ret;
+
+ ret = envs_read_validate_core(core, cpu_used);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int args_envs_read_search(const struct env_map_common *map,
+ int argc, char *const argv[])
+{
+ for (int i = 0; map[i].env_name; i++) {
+ if (!strcmp(argv[0], map[i].env_name))
+ return i;
+ }
+
+ pr_err("Unexpected argument '%s', can't parse\n", argv[0]);
+
+ return -ENOENT;
+}
+
+static int arg_read_set(const struct env_map_common *map, u32 i, int argc,
+ char *const argv[])
+{
+ char *endp = argv[1];
+
+ if (map[i].type == ENV_HEX)
+ map[i].val->val = simple_strtoul(argv[1], &endp, 16);
+ else
+ map[i].val->val = simple_strtoul(argv[1], &endp, 10);
+
+ map[i].val->set = true;
+
+ if (*endp == '\0')
+ return 0;
+
+ pr_err("Unexpected argument '%s', can't parse\n", argv[1]);
+
+ map[i].val->set = false;
+
+ return -EINVAL;
+}
+
+int args_envs_enumerate(const struct env_map_common *map, int enum_by,
+ int argc, char *const argv[])
+{
+ u32 i;
+
+ if (argc % enum_by) {
+ pr_err("unexpected argument number: %d\n", argc);
+ return -EINVAL;
+ }
+
+ while (argc > 0) {
+ i = args_envs_read_search(map, argc, argv);
+ if (i < 0)
+ return i;
+
+ debug("ARG: found '%s' with index %d\n", map[i].env_name, i);
+
+ if (i < 0) {
+ pr_err("unknown arg: %s\n", argv[0]);
+ return -EINVAL;
+ }
+
+ if (arg_read_set(map, i, argc, argv))
+ return -EINVAL;
+
+ debug("ARG: value.s '%s' == %#x\n", argv[1], map[i].val->val);
+
+ argc -= enum_by;
+ argv += enum_by;
+ }
+
+ return 0;
+}
diff --git a/board/synopsys/hsdk/env-lib.h b/board/synopsys/hsdk/env-lib.h
new file mode 100644
index 0000000000..606e802f0f
--- /dev/null
+++ b/board/synopsys/hsdk/env-lib.h
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ * Author: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __BOARD_ENV_LIB_H
+#define __BOARD_ENV_LIB_H
+
+#include <common.h>
+#include <config.h>
+#include <linux/kernel.h>
+
+enum env_type {
+ ENV_DEC,
+ ENV_HEX
+};
+
+typedef struct {
+ u32 val;
+ bool set;
+} u32_env;
+
+struct env_map_common {
+ const char *const env_name;
+ enum env_type type;
+ bool mandatory;
+ u32 min;
+ u32 max;
+ u32_env *val;
+};
+
+struct env_map_percpu {
+ const char *const env_name;
+ enum env_type type;
+ bool mandatory;
+ u32 min[NR_CPUS];
+ u32 max[NR_CPUS];
+ u32_env (*val)[NR_CPUS];
+};
+
+void envs_cleanup_common(const struct env_map_common *map);
+int envs_read_common(const struct env_map_common *map);
+int envs_validate_common(const struct env_map_common *map);
+int envs_read_validate_common(const struct env_map_common *map);
+
+void envs_cleanup_core(const struct env_map_percpu *map);
+int envs_read_validate_core(const struct env_map_percpu *map,
+ bool (*cpu_used)(u32));
+int envs_process_and_validate(const struct env_map_common *common,
+ const struct env_map_percpu *core,
+ bool (*cpu_used)(u32));
+
+int args_envs_enumerate(const struct env_map_common *map,
+ int enum_by, int argc, char *const argv[]);
+
+#endif /* __BOARD_ENV_LIB_H */
diff --git a/board/synopsys/hsdk/hsdk.c b/board/synopsys/hsdk/hsdk.c
index 5b3a063b69..65f937fd0f 100644
--- a/board/synopsys/hsdk/hsdk.c
+++ b/board/synopsys/hsdk/hsdk.c
@@ -1,59 +1,713 @@
/*
- * Copyright (C) 2017 Synopsys, Inc. All rights reserved.
+ * Copyright (C) 2018 Synopsys, Inc. All rights reserved.
+ * Author: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <config.h>
+#include <linux/printk.h>
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <asm/arcregs.h>
+#include <fdt_support.h>
#include <dwmmc.h>
#include <malloc.h>
+#include <usb.h>
+
+#include "clk-lib.h"
+#include "env-lib.h"
DECLARE_GLOBAL_DATA_PTR;
-#define CREG_BASE (ARC_PERIPHERAL_BASE + 0x1000)
-#define CREG_PAE (CREG_BASE + 0x180)
-#define CREG_PAE_UPDATE (CREG_BASE + 0x194)
-#define CREG_CPU_START (CREG_BASE + 0x400)
+#define ALL_CPU_MASK GENMASK(NR_CPUS - 1, 0)
+#define MASTER_CPU_ID 0
+#define APERTURE_SHIFT 28
+#define NO_CCM 0x10
+#define SLAVE_CPU_READY 0x12345678
+#define BOOTSTAGE_1 1 /* after SP, FP setup, before HW init */
+#define BOOTSTAGE_2 2 /* after HW init, before self halt */
+#define BOOTSTAGE_3 3 /* after self halt */
+#define BOOTSTAGE_4 4 /* before app launch */
+#define BOOTSTAGE_5 5 /* after app launch, unreachable */
-int board_early_init_f(void)
+#define RESET_VECTOR_ADDR 0x0
+
+#define CREG_BASE (ARC_PERIPHERAL_BASE + 0x1000)
+#define CREG_CPU_START (CREG_BASE + 0x400)
+#define CREG_CPU_START_MASK 0xF
+
+#define SDIO_BASE (ARC_PERIPHERAL_BASE + 0xA000)
+#define SDIO_UHS_REG_EXT (SDIO_BASE + 0x108)
+#define SDIO_UHS_REG_EXT_DIV_2 (2 << 30)
+
+/* Uncached access macros */
+#define arc_read_uncached_32(ptr) \
+({ \
+ unsigned int __ret; \
+ __asm__ __volatile__( \
+ " ld.di %0, [%1] \n" \
+ : "=r"(__ret) \
+ : "r"(ptr)); \
+ __ret; \
+})
+
+#define arc_write_uncached_32(ptr, data)\
+({ \
+ __asm__ __volatile__( \
+ " st.di %0, [%1] \n" \
+ : \
+ : "r"(data), "r"(ptr)); \
+})
+
+struct hsdk_env_core_ctl {
+ u32_env entry[NR_CPUS];
+ u32_env iccm[NR_CPUS];
+ u32_env dccm[NR_CPUS];
+};
+
+struct hsdk_env_common_ctl {
+ bool halt_on_boot;
+ u32_env core_mask;
+ u32_env cpu_freq;
+ u32_env axi_freq;
+ u32_env tun_freq;
+ u32_env nvlim;
+ u32_env icache;
+ u32_env dcache;
+};
+
+/*
+ * Uncached cross-cpu structure. All CPUs must access to this structure fields
+ * only with arc_read_uncached_32() / arc_write_uncached_32() accessors (which
+ * implement ld.di / st.di instructions). Simultaneous cached and uncached
+ * access to this area will lead to data loss.
+ * We flush all data caches in board_early_init_r() as we don't want to have
+ * any dirty line in L1d$ or SL$ in this area.
+ */
+struct hsdk_cross_cpu {
+ /* slave CPU ready flag */
+ u32 ready_flag;
+ /* address of the area, which can be used for stack by slave CPU */
+ u32 stack_ptr;
+ /* slave CPU status - bootstage number */
+ s32 status[NR_CPUS];
+
+ /*
+ * Slave CPU data - it is copy of corresponding fields in
+ * hsdk_env_core_ctl and hsdk_env_common_ctl structures which are
+ * required for slave CPUs initialization.
+ * This fields can be populated by copying from hsdk_env_core_ctl
+ * and hsdk_env_common_ctl structures with sync_cross_cpu_data()
+ * function.
+ */
+ u32 entry[NR_CPUS];
+ u32 iccm[NR_CPUS];
+ u32 dccm[NR_CPUS];
+
+ u32 core_mask;
+ u32 icache;
+ u32 dcache;
+
+ u8 cache_padding[ARCH_DMA_MINALIGN];
+} __aligned(ARCH_DMA_MINALIGN);
+
+/* Place for slave CPUs temporary stack */
+static u32 slave_stack[256 * NR_CPUS] __aligned(ARCH_DMA_MINALIGN);
+
+static struct hsdk_env_common_ctl env_common = {};
+static struct hsdk_env_core_ctl env_core = {};
+static struct hsdk_cross_cpu cross_cpu_data;
+
+static const struct env_map_common env_map_common[] = {
+ { "core_mask", ENV_HEX, true, 0x1, 0xF, &env_common.core_mask },
+ { "non_volatile_limit", ENV_HEX, true, 0, 0xF, &env_common.nvlim },
+ { "icache_ena", ENV_HEX, true, 0, 1, &env_common.icache },
+ { "dcache_ena", ENV_HEX, true, 0, 1, &env_common.dcache },
+ {}
+};
+
+static const struct env_map_common env_map_clock[] = {
+ { "cpu_freq", ENV_DEC, false, 100, 1000, &env_common.cpu_freq },
+ { "axi_freq", ENV_DEC, false, 200, 800, &env_common.axi_freq },
+ { "tun_freq", ENV_DEC, false, 0, 150, &env_common.tun_freq },
+ {}
+};
+
+static const struct env_map_percpu env_map_core[] = {
+ { "core_iccm", ENV_HEX, true, {NO_CCM, 0, NO_CCM, 0}, {NO_CCM, 0xF, NO_CCM, 0xF}, &env_core.iccm },
+ { "core_dccm", ENV_HEX, true, {NO_CCM, 0, NO_CCM, 0}, {NO_CCM, 0xF, NO_CCM, 0xF}, &env_core.dccm },
+ {}
+};
+
+static const struct env_map_common env_map_mask[] = {
+ { "core_mask", ENV_HEX, false, 0x1, 0xF, &env_common.core_mask },
+ {}
+};
+
+static const struct env_map_percpu env_map_go[] = {
+ { "core_entry", ENV_HEX, true, {0, 0, 0, 0}, {U32_MAX, U32_MAX, U32_MAX, U32_MAX}, &env_core.entry },
+ {}
+};
+
+static void sync_cross_cpu_data(void)
+{
+ u32 value;
+
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ value = env_core.entry[i].val;
+ arc_write_uncached_32(&cross_cpu_data.entry[i], value);
+ }
+
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ value = env_core.iccm[i].val;
+ arc_write_uncached_32(&cross_cpu_data.iccm[i], value);
+ }
+
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ value = env_core.dccm[i].val;
+ arc_write_uncached_32(&cross_cpu_data.dccm[i], value);
+ }
+
+ value = env_common.core_mask.val;
+ arc_write_uncached_32(&cross_cpu_data.core_mask, value);
+
+ value = env_common.icache.val;
+ arc_write_uncached_32(&cross_cpu_data.icache, value);
+
+ value = env_common.dcache.val;
+ arc_write_uncached_32(&cross_cpu_data.dcache, value);
+}
+
+/* Can be used only on master CPU */
+static bool is_cpu_used(u32 cpu_id)
{
- /* In current chip PAE support for DMA is broken, disabling it. */
- writel(0, (void __iomem *) CREG_PAE);
+ return !!(env_common.core_mask.val & BIT(cpu_id));
+}
- /* Really apply settings made above */
- writel(1, (void __iomem *) CREG_PAE_UPDATE);
+/* TODO: add ICCM BCR and DCCM BCR runtime check */
+static void init_slave_cpu_func(u32 core)
+{
+ u32 val;
+
+ /* Remap ICCM to another memory region if it exists */
+ val = arc_read_uncached_32(&cross_cpu_data.iccm[core]);
+ if (val != NO_CCM)
+ write_aux_reg(ARC_AUX_ICCM_BASE, val << APERTURE_SHIFT);
+
+ /* Remap DCCM to another memory region if it exists */
+ val = arc_read_uncached_32(&cross_cpu_data.dccm[core]);
+ if (val != NO_CCM)
+ write_aux_reg(ARC_AUX_DCCM_BASE, val << APERTURE_SHIFT);
+
+ if (arc_read_uncached_32(&cross_cpu_data.icache))
+ icache_enable();
+ else
+ icache_disable();
+
+ if (arc_read_uncached_32(&cross_cpu_data.dcache))
+ dcache_enable();
+ else
+ dcache_disable();
+}
+
+static void init_cluster_nvlim(void)
+{
+ u32 val = env_common.nvlim.val << APERTURE_SHIFT;
+
+ flush_dcache_all();
+ write_aux_reg(ARC_AUX_NON_VOLATILE_LIMIT, val);
+ write_aux_reg(AUX_AUX_CACHE_LIMIT, val);
+ flush_n_invalidate_dcache_all();
+}
+
+static void init_master_icache(void)
+{
+ if (icache_status()) {
+ /* I$ is enabled - we need to disable it */
+ if (!env_common.icache.val)
+ icache_disable();
+ } else {
+ /* I$ is disabled - we need to enable it */
+ if (env_common.icache.val) {
+ icache_enable();
+
+ /* invalidate I$ right after enable */
+ invalidate_icache_all();
+ }
+ }
+}
+
+static void init_master_dcache(void)
+{
+ if (dcache_status()) {
+ /* D$ is enabled - we need to disable it */
+ if (!env_common.dcache.val)
+ dcache_disable();
+ } else {
+ /* D$ is disabled - we need to enable it */
+ if (env_common.dcache.val)
+ dcache_enable();
+
+ /* TODO: probably we need ti invalidate D$ right after enable */
+ }
+}
+
+static int cleanup_before_go(void)
+{
+ disable_interrupts();
+ sync_n_cleanup_cache_all();
return 0;
}
-#define SDIO_BASE (ARC_PERIPHERAL_BASE + 0xA000)
-#define SDIO_UHS_REG_EXT (SDIO_BASE + 0x108)
-#define SDIO_UHS_REG_EXT_DIV_2 (2 << 30)
+void slave_cpu_set_boot_addr(u32 addr)
+{
+ /* All cores have reset vector pointing to 0 */
+ writel(addr, (void __iomem *)RESET_VECTOR_ADDR);
-int board_mmc_init(bd_t *bis)
+ /* Make sure other cores see written value in memory */
+ sync_n_cleanup_cache_all();
+}
+
+static inline void halt_this_cpu(void)
{
- struct dwmci_host *host = NULL;
+ __builtin_arc_flag(1);
+}
- host = malloc(sizeof(struct dwmci_host));
- if (!host) {
- printf("dwmci_host malloc fail!\n");
- return 1;
+static void smp_kick_cpu_x(u32 cpu_id)
+{
+ int cmd = readl((void __iomem *)CREG_CPU_START);
+
+ if (cpu_id > NR_CPUS)
+ return;
+
+ cmd &= ~CREG_CPU_START_MASK;
+ cmd |= (1 << cpu_id);
+ writel(cmd, (void __iomem *)CREG_CPU_START);
+}
+
+static u32 prepare_cpu_ctart_reg(void)
+{
+ int cmd = readl((void __iomem *)CREG_CPU_START);
+
+ cmd &= ~CREG_CPU_START_MASK;
+
+ return cmd | env_common.core_mask.val;
+}
+
+/* slave CPU entry for configuration */
+__attribute__((naked, noreturn, flatten)) noinline void hsdk_core_init_f(void)
+{
+ __asm__ __volatile__(
+ "ld.di r8, [%0]\n"
+ "mov %%sp, r8\n"
+ "mov %%fp, %%sp\n"
+ : /* no output */
+ : "r" (&cross_cpu_data.stack_ptr));
+
+ invalidate_icache_all();
+
+ arc_write_uncached_32(&cross_cpu_data.status[CPU_ID_GET()], BOOTSTAGE_1);
+ init_slave_cpu_func(CPU_ID_GET());
+
+ arc_write_uncached_32(&cross_cpu_data.ready_flag, SLAVE_CPU_READY);
+ arc_write_uncached_32(&cross_cpu_data.status[CPU_ID_GET()], BOOTSTAGE_2);
+
+ /* Halt the processor until the master kick us again */
+ halt_this_cpu();
+
+ /*
+ * 3 NOPs after FLAG 1 instruction are no longer required for ARCv2
+ * cores but we leave them for gebug purposes.
+ */
+ __builtin_arc_nop();
+ __builtin_arc_nop();
+ __builtin_arc_nop();
+
+ arc_write_uncached_32(&cross_cpu_data.status[CPU_ID_GET()], BOOTSTAGE_3);
+
+ /* get the updated entry - invalidate i$ */
+ invalidate_icache_all();
+
+ arc_write_uncached_32(&cross_cpu_data.status[CPU_ID_GET()], BOOTSTAGE_4);
+
+ /* Run our program */
+ ((void (*)(void))(arc_read_uncached_32(&cross_cpu_data.entry[CPU_ID_GET()])))();
+
+ /* This bootstage is unreachable as we don't return from app we launch */
+ arc_write_uncached_32(&cross_cpu_data.status[CPU_ID_GET()], BOOTSTAGE_5);
+
+ /* Something went terribly wrong */
+ while (true)
+ halt_this_cpu();
+}
+
+static void clear_cross_cpu_data(void)
+{
+ arc_write_uncached_32(&cross_cpu_data.ready_flag, 0);
+ arc_write_uncached_32(&cross_cpu_data.stack_ptr, 0);
+
+ for (u32 i = 0; i < NR_CPUS; i++)
+ arc_write_uncached_32(&cross_cpu_data.status[i], 0);
+}
+
+static noinline void do_init_slave_cpu(u32 cpu_id)
+{
+ /* attempts number for check clave CPU ready_flag */
+ u32 attempts = 100;
+ u32 stack_ptr = (u32)(slave_stack + (64 * cpu_id));
+
+ if (cpu_id >= NR_CPUS)
+ return;
+
+ arc_write_uncached_32(&cross_cpu_data.ready_flag, 0);
+
+ /* Use global unique place for each slave cpu stack */
+ arc_write_uncached_32(&cross_cpu_data.stack_ptr, stack_ptr);
+
+ debug("CPU %u: stack pool base: %p\n", cpu_id, slave_stack);
+ debug("CPU %u: current slave stack base: %x\n", cpu_id, stack_ptr);
+ slave_cpu_set_boot_addr((u32)hsdk_core_init_f);
+
+ smp_kick_cpu_x(cpu_id);
+
+ debug("CPU %u: cross-cpu flag: %x [before timeout]\n", cpu_id,
+ arc_read_uncached_32(&cross_cpu_data.ready_flag));
+
+ while (!arc_read_uncached_32(&cross_cpu_data.ready_flag) && attempts--)
+ mdelay(10);
+
+ /* Just to be sure that slave cpu is halted after it set ready_flag */
+ mdelay(20);
+
+ /*
+ * Only print error here if we reach timeout as there is no option to
+ * halt slave cpu (or check that slave cpu is halted)
+ */
+ if (!attempts)
+ pr_err("CPU %u is not responding after init!\n", cpu_id);
+
+ /* Check current stage of slave cpu */
+ if (arc_read_uncached_32(&cross_cpu_data.status[cpu_id]) != BOOTSTAGE_2)
+ pr_err("CPU %u status is unexpected: %d\n", cpu_id,
+ arc_read_uncached_32(&cross_cpu_data.status[cpu_id]));
+
+ debug("CPU %u: cross-cpu flag: %x [after timeout]\n", cpu_id,
+ arc_read_uncached_32(&cross_cpu_data.ready_flag));
+ debug("CPU %u: status: %d [after timeout]\n", cpu_id,
+ arc_read_uncached_32(&cross_cpu_data.status[cpu_id]));
+}
+
+static void do_init_slave_cpus(void)
+{
+ clear_cross_cpu_data();
+ sync_cross_cpu_data();
+
+ debug("cross_cpu_data location: %#x\n", (u32)&cross_cpu_data);
+
+ for (u32 i = MASTER_CPU_ID + 1; i < NR_CPUS; i++)
+ if (is_cpu_used(i))
+ do_init_slave_cpu(i);
+}
+
+static void do_init_master_cpu(void)
+{
+ /*
+ * Setup master caches even if master isn't used as we want to use
+ * same cache configuration on all running CPUs
+ */
+ init_master_icache();
+ init_master_dcache();
+}
+
+enum hsdk_axi_masters {
+ M_HS_CORE = 0,
+ M_HS_RTT,
+ M_AXI_TUN,
+ M_HDMI_VIDEO,
+ M_HDMI_AUDIO,
+ M_USB_HOST,
+ M_ETHERNET,
+ M_SDIO,
+ M_GPU,
+ M_DMAC_0,
+ M_DMAC_1,
+ M_DVFS
+};
+
+#define UPDATE_VAL 1
+
+/*
+ * m master AXI_M_m_SLV0 AXI_M_m_SLV1 AXI_M_m_OFFSET0 AXI_M_m_OFFSET1
+ * 0 HS (CBU) 0x11111111 0x63111111 0xFEDCBA98 0x0E543210
+ * 1 HS (RTT) 0x77777777 0x77777777 0xFEDCBA98 0x76543210
+ * 2 AXI Tunnel 0x88888888 0x88888888 0xFEDCBA98 0x76543210
+ * 3 HDMI-VIDEO 0x77777777 0x77777777 0xFEDCBA98 0x76543210
+ * 4 HDMI-ADUIO 0x77777777 0x77777777 0xFEDCBA98 0x76543210
+ * 5 USB-HOST 0x77777777 0x77999999 0xFEDCBA98 0x76DCBA98
+ * 6 ETHERNET 0x77777777 0x77999999 0xFEDCBA98 0x76DCBA98
+ * 7 SDIO 0x77777777 0x77999999 0xFEDCBA98 0x76DCBA98
+ * 8 GPU 0x77777777 0x77777777 0xFEDCBA98 0x76543210
+ * 9 DMAC (port #1) 0x77777777 0x77777777 0xFEDCBA98 0x76543210
+ * 10 DMAC (port #2) 0x77777777 0x77777777 0xFEDCBA98 0x76543210
+ * 11 DVFS 0x00000000 0x60000000 0x00000000 0x00000000
+ *
+ * Please read ARC HS Development IC Specification, section 17.2 for more
+ * information about apertures configuration.
+ * NOTE: we intentionally modify default settings in U-boot. Default settings
+ * are specified in "Table 111 CREG Address Decoder register reset values".
+ */
+
+#define CREG_AXI_M_SLV0(m) ((void __iomem *)(CREG_BASE + 0x020 * (m)))
+#define CREG_AXI_M_SLV1(m) ((void __iomem *)(CREG_BASE + 0x020 * (m) + 0x004))
+#define CREG_AXI_M_OFT0(m) ((void __iomem *)(CREG_BASE + 0x020 * (m) + 0x008))
+#define CREG_AXI_M_OFT1(m) ((void __iomem *)(CREG_BASE + 0x020 * (m) + 0x00C))
+#define CREG_AXI_M_UPDT(m) ((void __iomem *)(CREG_BASE + 0x020 * (m) + 0x014))
+
+#define CREG_AXI_M_HS_CORE_BOOT ((void __iomem *)(CREG_BASE + 0x010))
+
+#define CREG_PAE ((void __iomem *)(CREG_BASE + 0x180))
+#define CREG_PAE_UPDT ((void __iomem *)(CREG_BASE + 0x194))
+
+void init_memory_bridge(void)
+{
+ u32 reg;
+
+ /*
+ * M_HS_CORE has one unic register - BOOT.
+ * We need to clean boot mirror (BOOT[1:0]) bits in them.
+ */
+ reg = readl(CREG_AXI_M_HS_CORE_BOOT) & (~0x3);
+ writel(reg, CREG_AXI_M_HS_CORE_BOOT);
+ writel(0x11111111, CREG_AXI_M_SLV0(M_HS_CORE));
+ writel(0x63111111, CREG_AXI_M_SLV1(M_HS_CORE));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HS_CORE));
+ writel(0x0E543210, CREG_AXI_M_OFT1(M_HS_CORE));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HS_CORE));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_HS_RTT));
+ writel(0x77777777, CREG_AXI_M_SLV1(M_HS_RTT));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HS_RTT));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_HS_RTT));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HS_RTT));
+
+ writel(0x88888888, CREG_AXI_M_SLV0(M_AXI_TUN));
+ writel(0x88888888, CREG_AXI_M_SLV1(M_AXI_TUN));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_AXI_TUN));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_AXI_TUN));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_AXI_TUN));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_HDMI_VIDEO));
+ writel(0x77777777, CREG_AXI_M_SLV1(M_HDMI_VIDEO));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HDMI_VIDEO));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_HDMI_VIDEO));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HDMI_VIDEO));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_HDMI_AUDIO));
+ writel(0x77777777, CREG_AXI_M_SLV1(M_HDMI_AUDIO));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HDMI_AUDIO));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_HDMI_AUDIO));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HDMI_AUDIO));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_USB_HOST));
+ writel(0x77999999, CREG_AXI_M_SLV1(M_USB_HOST));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_USB_HOST));
+ writel(0x76DCBA98, CREG_AXI_M_OFT1(M_USB_HOST));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_USB_HOST));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_ETHERNET));
+ writel(0x77999999, CREG_AXI_M_SLV1(M_ETHERNET));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_ETHERNET));
+ writel(0x76DCBA98, CREG_AXI_M_OFT1(M_ETHERNET));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_ETHERNET));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_SDIO));
+ writel(0x77999999, CREG_AXI_M_SLV1(M_SDIO));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_SDIO));
+ writel(0x76DCBA98, CREG_AXI_M_OFT1(M_SDIO));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_SDIO));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_GPU));
+ writel(0x77777777, CREG_AXI_M_SLV1(M_GPU));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_GPU));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_GPU));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_GPU));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_DMAC_0));
+ writel(0x77777777, CREG_AXI_M_SLV1(M_DMAC_0));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_DMAC_0));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_DMAC_0));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_DMAC_0));
+
+ writel(0x77777777, CREG_AXI_M_SLV0(M_DMAC_1));
+ writel(0x77777777, CREG_AXI_M_SLV1(M_DMAC_1));
+ writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_DMAC_1));
+ writel(0x76543210, CREG_AXI_M_OFT1(M_DMAC_1));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_DMAC_1));
+
+ writel(0x00000000, CREG_AXI_M_SLV0(M_DVFS));
+ writel(0x60000000, CREG_AXI_M_SLV1(M_DVFS));
+ writel(0x00000000, CREG_AXI_M_OFT0(M_DVFS));
+ writel(0x00000000, CREG_AXI_M_OFT1(M_DVFS));
+ writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_DVFS));
+
+ writel(0x00000000, CREG_PAE);
+ writel(UPDATE_VAL, CREG_PAE_UPDT);
+}
+
+static void setup_clocks(void)
+{
+ ulong rate;
+
+ /* Setup CPU clock */
+ if (env_common.cpu_freq.set) {
+ rate = env_common.cpu_freq.val;
+ soc_clk_ctl("cpu-clk", &rate, CLK_ON | CLK_SET | CLK_MHZ);
}
+ /* Setup TUN clock */
+ if (env_common.tun_freq.set) {
+ rate = env_common.tun_freq.val;
+ if (rate)
+ soc_clk_ctl("tun-clk", &rate, CLK_ON | CLK_SET | CLK_MHZ);
+ else
+ soc_clk_ctl("tun-clk", NULL, CLK_OFF);
+ }
+
+ if (env_common.axi_freq.set) {
+ rate = env_common.axi_freq.val;
+ soc_clk_ctl("axi-clk", &rate, CLK_SET | CLK_ON | CLK_MHZ);
+ }
+}
+
+static void do_init_cluster(void)
+{
/*
- * Switch SDIO external ciu clock divider from default div-by-8 to
- * minimum possible div-by-2.
+ * A multi-core ARC HS configuration always includes only one
+ * ARC_AUX_NON_VOLATILE_LIMIT register, which is shared by all the
+ * cores.
*/
- writel(SDIO_UHS_REG_EXT_DIV_2, (void __iomem *) SDIO_UHS_REG_EXT);
+ init_cluster_nvlim();
+}
- memset(host, 0, sizeof(struct dwmci_host));
- host->name = "Synopsys Mobile storage";
- host->ioaddr = (void *)ARC_DWMMC_BASE;
- host->buswidth = 4;
- host->dev_index = 0;
- host->bus_hz = 50000000;
+static int check_master_cpu_id(void)
+{
+ if (CPU_ID_GET() == MASTER_CPU_ID)
+ return 0;
- add_dwmci(host, host->bus_hz / 2, 400000);
+ pr_err("u-boot runs on non-master cpu with id: %lu\n", CPU_ID_GET());
+
+ return -ENOENT;
+}
+
+static noinline int prepare_cpus(void)
+{
+ int ret;
+
+ ret = check_master_cpu_id();
+ if (ret)
+ return ret;
+
+ ret = envs_process_and_validate(env_map_common, env_map_core, is_cpu_used);
+ if (ret)
+ return ret;
+
+ printf("CPU start mask is %#x\n", env_common.core_mask.val);
+
+ do_init_slave_cpus();
+ do_init_master_cpu();
+ do_init_cluster();
+
+ return 0;
+}
+
+static int hsdk_go_run(u32 cpu_start_reg)
+{
+ /* Cleanup caches, disable interrupts */
+ cleanup_before_go();
+
+ if (env_common.halt_on_boot)
+ halt_this_cpu();
+
+ /*
+ * 3 NOPs after FLAG 1 instruction are no longer required for ARCv2
+ * cores but we leave them for gebug purposes.
+ */
+ __builtin_arc_nop();
+ __builtin_arc_nop();
+ __builtin_arc_nop();
+
+ /* Kick chosen slave CPUs */
+ writel(cpu_start_reg, (void __iomem *)CREG_CPU_START);
+
+ if (is_cpu_used(MASTER_CPU_ID))
+ ((void (*)(void))(env_core.entry[MASTER_CPU_ID].val))();
+ else
+ halt_this_cpu();
+
+ pr_err("u-boot still runs on cpu [%ld]\n", CPU_ID_GET());
+
+ /*
+ * We will never return after executing our program if master cpu used
+ * otherwise halt master cpu manually.
+ */
+ while (true)
+ halt_this_cpu();
+
+ return 0;
+}
+
+int board_prep_linux(bootm_headers_t *images)
+{
+ int ret, ofst;
+ char mask[15];
+
+ ret = envs_read_validate_common(env_map_mask);
+ if (ret)
+ return ret;
+
+ /* Rollback to default values */
+ if (!env_common.core_mask.set) {
+ env_common.core_mask.val = ALL_CPU_MASK;
+ env_common.core_mask.set = true;
+ }
+
+ printf("CPU start mask is %#x\n", env_common.core_mask.val);
+
+ if (!is_cpu_used(MASTER_CPU_ID))
+ pr_err("ERR: try to launch linux with CPU[0] disabled! It doesn't work for ARC.\n");
+
+ /*
+ * If we want to launch linux on all CPUs we don't need to patch
+ * linux DTB as it is default configuration
+ */
+ if (env_common.core_mask.val == ALL_CPU_MASK)
+ return 0;
+
+ if (!IMAGE_ENABLE_OF_LIBFDT || !images->ft_len) {
+ pr_err("WARN: core_mask setup will work properly only with external DTB!\n");
+ return 0;
+ }
+
+ /* patch '/possible-cpus' property according to cpu mask */
+ ofst = fdt_path_offset(images->ft_addr, "/");
+ sprintf(mask, "%s%s%s%s",
+ is_cpu_used(0) ? "0," : "",
+ is_cpu_used(1) ? "1," : "",
+ is_cpu_used(2) ? "2," : "",
+ is_cpu_used(3) ? "3," : "");
+ ret = fdt_setprop_string(images->ft_addr, ofst, "possible-cpus", mask);
+ /*
+ * If we failed to patch '/possible-cpus' property we don't need break
+ * linux loading process: kernel will handle it but linux will print
+ * warning like "Timeout: CPU1 FAILED to comeup !!!".
+ * So warn here about error, but return 0 like no error had occurred.
+ */
+ if (ret)
+ pr_err("WARN: failed to patch '/possible-cpus' property, ret=%d\n",
+ ret);
return 0;
}
@@ -61,35 +715,335 @@ int board_mmc_init(bd_t *bis)
void board_jump_and_run(ulong entry, int zero, int arch, uint params)
{
void (*kernel_entry)(int zero, int arch, uint params);
+ u32 cpu_start_reg;
kernel_entry = (void (*)(int, int, uint))entry;
- smp_set_core_boot_addr(entry, -1);
- smp_kick_all_cpus();
- kernel_entry(zero, arch, params);
+ /* Prepare CREG_CPU_START for kicking chosen CPUs */
+ cpu_start_reg = prepare_cpu_ctart_reg();
+
+ /* In case of run without hsdk_init */
+ slave_cpu_set_boot_addr(entry);
+
+ /* In case of run with hsdk_init */
+ for (u32 i = 0; i < NR_CPUS; i++) {
+ env_core.entry[i].val = entry;
+ env_core.entry[i].set = true;
+ }
+ /* sync cross_cpu struct as we updated core-entry variables */
+ sync_cross_cpu_data();
+
+ /* Kick chosen slave CPUs */
+ writel(cpu_start_reg, (void __iomem *)CREG_CPU_START);
+
+ if (is_cpu_used(0))
+ kernel_entry(zero, arch, params);
}
-#define RESET_VECTOR_ADDR 0x0
+static int hsdk_go_prepare_and_run(void)
+{
+ /* Prepare CREG_CPU_START for kicking chosen CPUs */
+ u32 reg = prepare_cpu_ctart_reg();
+
+ if (env_common.halt_on_boot)
+ printf("CPU will halt before application start, start application with debugger.\n");
-void smp_set_core_boot_addr(unsigned long addr, int corenr)
+ return hsdk_go_run(reg);
+}
+
+static int do_hsdk_go(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
{
- /* All cores have reset vector pointing to 0 */
- writel(addr, (void __iomem *)RESET_VECTOR_ADDR);
+ int ret;
- /* Make sure other cores see written value in memory */
+ /*
+ * Check for 'halt' parameter. 'halt' = enter halt-mode just before
+ * starting the application; can be used for debug.
+ */
+ if (argc > 1) {
+ env_common.halt_on_boot = !strcmp(argv[1], "halt");
+ if (!env_common.halt_on_boot) {
+ pr_err("Unrecognised parameter: \'%s\'\n", argv[1]);
+ return CMD_RET_FAILURE;
+ }
+ }
+
+ ret = check_master_cpu_id();
+ if (ret)
+ return ret;
+
+ ret = envs_process_and_validate(env_map_mask, env_map_go, is_cpu_used);
+ if (ret)
+ return ret;
+
+ /* sync cross_cpu struct as we updated core-entry variables */
+ sync_cross_cpu_data();
+
+ ret = hsdk_go_prepare_and_run();
+
+ return ret ? CMD_RET_FAILURE : CMD_RET_SUCCESS;
+}
+
+U_BOOT_CMD(
+ hsdk_go, 3, 0, do_hsdk_go,
+ "Synopsys HSDK specific command",
+ " - Boot stand-alone application on HSDK\n"
+ "hsdk_go halt - Boot stand-alone application on HSDK, halt CPU just before application run\n"
+);
+
+static int do_hsdk_init(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ static bool done = false;
+ int ret;
+
+ /* hsdk_init can be run only once */
+ if (done) {
+ printf("HSDK HW is already initialized! Please reset the board if you want to change the configuration.\n");
+ return CMD_RET_FAILURE;
+ }
+
+ ret = prepare_cpus();
+ if (!ret)
+ done = true;
+
+ return ret ? CMD_RET_FAILURE : CMD_RET_SUCCESS;
+}
+
+U_BOOT_CMD(
+ hsdk_init, 1, 0, do_hsdk_init,
+ "Synopsys HSDK specific command",
+ "- Init HSDK HW\n"
+);
+
+static int do_hsdk_clock_set(cmd_tbl_t *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ int ret = 0;
+
+ /* Strip off leading subcommand argument */
+ argc--;
+ argv++;
+
+ envs_cleanup_common(env_map_clock);
+
+ if (!argc) {
+ printf("Set clocks to values specified in environment\n");
+ ret = envs_read_common(env_map_clock);
+ } else {
+ printf("Set clocks to values specified in args\n");
+ ret = args_envs_enumerate(env_map_clock, 2, argc, argv);
+ }
+
+ if (ret)
+ return CMD_RET_FAILURE;
+
+ ret = envs_validate_common(env_map_clock);
+ if (ret)
+ return CMD_RET_FAILURE;
+
+ /* Setup clock tree HW */
+ setup_clocks();
+
+ return CMD_RET_SUCCESS;
+}
+
+static int do_hsdk_clock_get(cmd_tbl_t *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ ulong rate;
+
+ if (soc_clk_ctl("cpu-clk", &rate, CLK_GET | CLK_MHZ))
+ return CMD_RET_FAILURE;
+
+ if (env_set_ulong("cpu_freq", rate))
+ return CMD_RET_FAILURE;
+
+ if (soc_clk_ctl("tun-clk", &rate, CLK_GET | CLK_MHZ))
+ return CMD_RET_FAILURE;
+
+ if (env_set_ulong("tun_freq", rate))
+ return CMD_RET_FAILURE;
+
+ if (soc_clk_ctl("axi-clk", &rate, CLK_GET | CLK_MHZ))
+ return CMD_RET_FAILURE;
+
+ if (env_set_ulong("axi_freq", rate))
+ return CMD_RET_FAILURE;
+
+ printf("Clock values are saved to environment\n");
+
+ return CMD_RET_SUCCESS;
+}
+
+static int do_hsdk_clock_print(cmd_tbl_t *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ /* Main clocks */
+ soc_clk_ctl("cpu-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("tun-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("axi-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("ddr-clk", NULL, CLK_PRINT | CLK_MHZ);
+
+ return CMD_RET_SUCCESS;
+}
+
+static int do_hsdk_clock_print_all(cmd_tbl_t *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ /*
+ * NOTE: as of today we don't use some peripherals like HDMI / EBI
+ * so we don't want to print their clocks ("hdmi-sys-clk", "hdmi-pll",
+ * "hdmi-clk", "ebi-clk"). Nevertheless their clock subsystems is fully
+ * functional and we can print their clocks if it is required
+ */
+
+ /* CPU clock domain */
+ soc_clk_ctl("cpu-pll", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("cpu-clk", NULL, CLK_PRINT | CLK_MHZ);
+ printf("\n");
+
+ /* SYS clock domain */
+ soc_clk_ctl("sys-pll", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("apb-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("axi-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("eth-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("usb-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("sdio-clk", NULL, CLK_PRINT | CLK_MHZ);
+/* soc_clk_ctl("hdmi-sys-clk", NULL, CLK_PRINT | CLK_MHZ); */
+ soc_clk_ctl("gfx-core-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("gfx-dma-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("gfx-cfg-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("dmac-core-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("dmac-cfg-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("sdio-ref-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("spi-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("i2c-clk", NULL, CLK_PRINT | CLK_MHZ);
+/* soc_clk_ctl("ebi-clk", NULL, CLK_PRINT | CLK_MHZ); */
+ soc_clk_ctl("uart-clk", NULL, CLK_PRINT | CLK_MHZ);
+ printf("\n");
+
+ /* DDR clock domain */
+ soc_clk_ctl("ddr-clk", NULL, CLK_PRINT | CLK_MHZ);
+ printf("\n");
+
+ /* HDMI clock domain */
+/* soc_clk_ctl("hdmi-pll", NULL, CLK_PRINT | CLK_MHZ); */
+/* soc_clk_ctl("hdmi-clk", NULL, CLK_PRINT | CLK_MHZ); */
+/* printf("\n"); */
+
+ /* TUN clock domain */
+ soc_clk_ctl("tun-pll", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("tun-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("rom-clk", NULL, CLK_PRINT | CLK_MHZ);
+ soc_clk_ctl("pwm-clk", NULL, CLK_PRINT | CLK_MHZ);
+ printf("\n");
+
+ return CMD_RET_SUCCESS;
+}
+
+cmd_tbl_t cmd_hsdk_clock[] = {
+ U_BOOT_CMD_MKENT(set, 3, 0, do_hsdk_clock_set, "", ""),
+ U_BOOT_CMD_MKENT(get, 3, 0, do_hsdk_clock_get, "", ""),
+ U_BOOT_CMD_MKENT(print, 4, 0, do_hsdk_clock_print, "", ""),
+ U_BOOT_CMD_MKENT(print_all, 4, 0, do_hsdk_clock_print_all, "", ""),
+};
+
+static int do_hsdk_clock(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ cmd_tbl_t *c;
+
+ if (argc < 2)
+ return CMD_RET_USAGE;
+
+ /* Strip off leading 'hsdk_clock' command argument */
+ argc--;
+ argv++;
+
+ c = find_cmd_tbl(argv[0], cmd_hsdk_clock, ARRAY_SIZE(cmd_hsdk_clock));
+ if (!c)
+ return CMD_RET_USAGE;
+
+ return c->cmd(cmdtp, flag, argc, argv);
+}
+
+U_BOOT_CMD(
+ hsdk_clock, CONFIG_SYS_MAXARGS, 0, do_hsdk_clock,
+ "Synopsys HSDK specific clock command",
+ "set - Set clock to values specified in environment / command line arguments\n"
+ "hsdk_clock get - Save clock values to environment\n"
+ "hsdk_clock print - Print main clock values to console\n"
+ "hsdk_clock print_all - Print all clock values to console\n"
+);
+
+/* init calls */
+int board_early_init_f(void)
+{
+ /*
+ * Setup AXI apertures unconditionally as we want to have DDR
+ * in 0x00000000 region when we are kicking slave cpus.
+ */
+ init_memory_bridge();
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ /*
+ * TODO: Init USB here to be able read environment from USB MSD.
+ * It can be done with usb_init() call. We can't do it right now
+ * due to brocken USB IP SW reset and lack of USB IP HW reset in
+ * linux kernel (if we init USB here we will break USB in linux)
+ */
+
+ /*
+ * Flush all d$ as we want to use uncached area with st.di / ld.di
+ * instructions and we don't want to have any dirty line in L1d$ or SL$
+ * in this area. It is enough to flush all d$ once here as we access to
+ * uncached area with regular st (non .di) instruction only when we copy
+ * data during u-boot relocation.
+ */
flush_dcache_all();
+
+ printf("Relocation Offset is: %08lx\n", gd->reloc_off);
+
+ return 0;
}
-void smp_kick_all_cpus(void)
+int board_late_init(void)
{
-#define BITS_START_CORE1 1
-#define BITS_START_CORE2 2
-#define BITS_START_CORE3 3
+ /*
+ * Populate environment with clock frequency values -
+ * run hsdk_clock get callback without uboot command run.
+ */
+ do_hsdk_clock_get(NULL, 0, 0, NULL);
- int cmd = readl((void __iomem *)CREG_CPU_START);
+ return 0;
+}
- cmd |= (1 << BITS_START_CORE1) |
- (1 << BITS_START_CORE2) |
- (1 << BITS_START_CORE3);
- writel(cmd, (void __iomem *)CREG_CPU_START);
+int board_mmc_init(bd_t *bis)
+{
+ struct dwmci_host *host = NULL;
+
+ host = malloc(sizeof(struct dwmci_host));
+ if (!host) {
+ printf("dwmci_host malloc fail!\n");
+ return 1;
+ }
+
+ /*
+ * Switch SDIO external ciu clock divider from default div-by-8 to
+ * minimum possible div-by-2.
+ */
+ writel(SDIO_UHS_REG_EXT_DIV_2, (void __iomem *)SDIO_UHS_REG_EXT);
+
+ memset(host, 0, sizeof(struct dwmci_host));
+ host->name = "Synopsys Mobile storage";
+ host->ioaddr = (void *)ARC_DWMMC_BASE;
+ host->buswidth = 4;
+ host->dev_index = 0;
+ host->bus_hz = 50000000;
+
+ add_dwmci(host, host->bus_hz / 2, 400000);
+
+ return 0;
}
diff --git a/configs/hsdk_defconfig b/configs/hsdk_defconfig
index 11cb7e03a6..c72ee2d0c1 100644
--- a/configs/hsdk_defconfig
+++ b/configs/hsdk_defconfig
@@ -7,13 +7,16 @@ CONFIG_DEFAULT_DEVICE_TREE="hsdk"
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200n8"
CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="hsdk# "
+CONFIG_CMD_ENV_FLAGS=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
@@ -25,6 +28,7 @@ CONFIG_ENV_FAT_INTERFACE="mmc"
CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
+CONFIG_CLK_HSDK=y
CONFIG_MMC=y
CONFIG_MMC_DW=y
CONFIG_DM_ETH=y
diff --git a/include/configs/hsdk.h b/include/configs/hsdk.h
index fb4829ab46..ac86f31142 100644
--- a/include/configs/hsdk.h
+++ b/include/configs/hsdk.h
@@ -12,6 +12,7 @@
/*
* CPU configuration
*/
+#define NR_CPUS 4
#define ARC_PERIPHERAL_BASE 0xF0000000
#define ARC_DWMMC_BASE (ARC_PERIPHERAL_BASE + 0xA000)
#define ARC_DWGMAC_BASE (ARC_PERIPHERAL_BASE + 0x18000)
@@ -61,6 +62,50 @@
*/
#define CONFIG_ENV_SIZE SZ_16K
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "core_dccm_0=0x10\0" \
+ "core_dccm_1=0x6\0" \
+ "core_dccm_2=0x10\0" \
+ "core_dccm_3=0x6\0" \
+ "core_iccm_0=0x10\0" \
+ "core_iccm_1=0x6\0" \
+ "core_iccm_2=0x10\0" \
+ "core_iccm_3=0x6\0" \
+ "core_mask=0xF\0" \
+ "dcache_ena=0x1\0" \
+ "icache_ena=0x1\0" \
+ "non_volatile_limit=0xE\0" \
+ "hsdk_hs34=setenv core_mask 0x2; setenv icache_ena 0x0; \
+setenv dcache_ena 0x0; setenv core_iccm_1 0x7; \
+setenv core_dccm_1 0x8; setenv non_volatile_limit 0x0;\0" \
+ "hsdk_hs36=setenv core_mask 0x1; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_0 0x10; \
+setenv core_dccm_0 0x10; setenv non_volatile_limit 0xE;\0" \
+ "hsdk_hs36_ccm=setenv core_mask 0x2; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_1 0x7; \
+setenv core_dccm_1 0x8; setenv non_volatile_limit 0xE;\0" \
+ "hsdk_hs38=setenv core_mask 0x1; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_0 0x10; \
+setenv core_dccm_0 0x10; setenv non_volatile_limit 0xE;\0" \
+ "hsdk_hs38_ccm=setenv core_mask 0x2; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_1 0x7; \
+setenv core_dccm_1 0x8; setenv non_volatile_limit 0xE;\0" \
+ "hsdk_hs38x2=setenv core_mask 0x3; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_0 0x10; \
+setenv core_dccm_0 0x10; setenv non_volatile_limit 0xE; \
+setenv core_iccm_1 0x6; setenv core_dccm_1 0x6;\0" \
+ "hsdk_hs38x3=setenv core_mask 0x7; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_0 0x10; \
+setenv core_dccm_0 0x10; setenv non_volatile_limit 0xE; \
+setenv core_iccm_1 0x6; setenv core_dccm_1 0x6; \
+setenv core_iccm_2 0x10; setenv core_dccm_2 0x10;\0" \
+ "hsdk_hs38x4=setenv core_mask 0xF; setenv icache_ena 0x1; \
+setenv dcache_ena 0x1; setenv core_iccm_0 0x10; \
+setenv core_dccm_0 0x10; setenv non_volatile_limit 0xE; \
+setenv core_iccm_1 0x6; setenv core_dccm_1 0x6; \
+setenv core_iccm_2 0x10; setenv core_dccm_2 0x10; \
+setenv core_iccm_3 0x6; setenv core_dccm_3 0x6;\0"
+
/*
* Environment configuration
*/
@@ -68,12 +113,17 @@
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
/*
- * Console configuration
+ * Misc utility configuration
*/
+#define CONFIG_BOUNCE_BUFFER
+
+/* Cli configuration */
+#define CONFIG_SYS_CBSIZE SZ_2K
/*
- * Misc utility configuration
+ * Callback configuration
*/
-#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_BOARD_LATE_INIT
#endif /* _CONFIG_HSDK_H_ */
--
2.14.3
^ permalink raw reply related [flat|nested] 7+ messages in thread