From: Masami Hiramatsu <masami.hiramatsu@linaro.org>
To: u-boot@lists.denx.de
Subject: [PATCH v3 14/14] configs: synquacer: Enable EFI capsule update support
Date: Mon, 10 May 2021 15:33:24 +0900 [thread overview]
Message-ID: <162062840411.501222.16663129773006491967.stgit@localhost> (raw)
In-Reply-To: <162062825393.501222.13616174511857694530.stgit@localhost>
Enable EFI capsule update support. With the EFI capsule update,
you can update U-Boot, TF-A and OP-TEE. TF-A and OP-TEE are
usually combined as a FIP binary, but if the binary is bigger
than 480KB, you have to modify FIP header, split the OP-TEE
and stores the OP-TEE binary in the different place. This
configuration supports both cases.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
---
Changes in v3:
- Fix a typo in dfu_alt_info.
---
configs/synquacer_developerbox_defconfig | 15 +++++++++++++++
include/configs/synquacer.h | 6 ++++++
2 files changed, 21 insertions(+)
diff --git a/configs/synquacer_developerbox_defconfig b/configs/synquacer_developerbox_defconfig
index de12587775..428c66fa58 100644
--- a/configs/synquacer_developerbox_defconfig
+++ b/configs/synquacer_developerbox_defconfig
@@ -92,3 +92,18 @@ CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PCI=y
CONFIG_USB_STORAGE=y
+CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y
+CONFIG_EFI_CAPSULE_ON_DISK=y
+CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y
+CONFIG_EFI_CAPSULE_FIRMWARE_FIT=y
+CONFIG_CMD_EFIDEBUG=y
+CONFIG_CMD_DFU=y
+CONFIG_DFU_TFTP=y
+CONFIG_DFU_MTD=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_SF=y
+CONFIG_DFU_SF_PART=y
+CONFIG_FIT=y
+CONFIG_OF_LIBFDT=y
+CONFIG_CMD_NVEDIT_EFI=y
+CONFIG_CMD_ERASEENV=y
diff --git a/include/configs/synquacer.h b/include/configs/synquacer.h
index b2dd6d0f0f..f88fa21eff 100644
--- a/include/configs/synquacer.h
+++ b/include/configs/synquacer.h
@@ -58,6 +58,11 @@
/* Since U-Boot 64bit PCIe support is limited, disable 64bit MMIO support */
/* #define CONFIG_SYS_PCI_64BIT 1 */
+#define DEFAULT_DFU_ALT_INFO "dfu_alt_info=" \
+ "mtd nor1=u-boot.bin raw 200000 100000;" \
+ "fip.bin raw 180000 78000;" \
+ "optee.bin raw 500000 100000\0"
+
/* Distro boot settings */
#ifndef CONFIG_SPL_BUILD
#ifdef CONFIG_CMD_USB
@@ -101,6 +106,7 @@
"ramdisk_addr_r=0xa0000000\0" \
"scriptaddr=0x88000000\0" \
"pxefile_addr_r=0x88100000\0" \
+ DEFAULT_DFU_ALT_INFO \
BOOTENV
#endif /* __CONFIG_H */
prev parent reply other threads:[~2021-05-10 6:33 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-10 6:30 [PATCH v3 00/14] arm64: synquacer: Add SynQuacer/DeveloperBox support Masami Hiramatsu
2021-05-10 6:31 ` [PATCH v3 01/14] pci: Update the highest subordinate bus number for bridge setup Masami Hiramatsu
2021-05-10 6:31 ` [PATCH v3 02/14] ata: ahci-pci: Use scsi_ops to initialize ops Masami Hiramatsu
2021-05-10 6:31 ` [PATCH v3 03/14] dm: pci: Skip setting VGA bridge bits if parent device is the host bus Masami Hiramatsu
2021-05-10 6:31 ` [PATCH v3 04/14] efi: Fix to use null handle to create new handle for efi_fmp_raw Masami Hiramatsu
2021-05-10 6:31 ` [PATCH v3 05/14] gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs Masami Hiramatsu
2021-05-10 6:31 ` [PATCH v3 06/14] pci: synquacer: Add SynQuacer ECAM based PCIe driver Masami Hiramatsu
2021-05-10 6:32 ` [PATCH v3 07/14] mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver Masami Hiramatsu
2021-05-10 22:09 ` Jaehoon Chung
2021-05-10 6:32 ` [PATCH v3 08/14] spi: synquacer: Add HSSPI SPI controller driver for SynQuacer Masami Hiramatsu
2021-05-10 6:32 ` [PATCH v3 09/14] net: synquacer: Add netsec driver Masami Hiramatsu
2021-05-10 6:32 ` [PATCH v3 10/14] ARM: dts: synquacer: Add device trees for DeveloperBox Masami Hiramatsu
2021-05-10 6:32 ` [PATCH v3 11/14] board: synquacer: Add DeveloperBox 96boards EE support Masami Hiramatsu
2021-05-10 6:33 ` [PATCH v3 12/14] dfu_mtd: Ignore non-implemented lock device failure Masami Hiramatsu
2021-05-10 6:33 ` [PATCH v3 13/14] doc: qemu: arm64: Fix the documentation of capsule update Masami Hiramatsu
2021-05-10 6:33 ` Masami Hiramatsu [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=162062840411.501222.16663129773006491967.stgit@localhost \
--to=masami.hiramatsu@linaro.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox