[U-Boot] [PATCH v2 01/13] mx31: Move EHCI definitions to ehci-fsl.h

["Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>]

Hi Stefano,

On Saturday, November 10, 2012 8:42:24 AM, Stefano Babic wrote:
> On 08/11/2012 21:27, Beno?t Th?baudeau wrote:
> > The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so
> > move them to
> > ehci-fsl.h so that all MXC SoCs can use them.
> > 
> > Signed-off-by: Beno?t Th?baudeau <benoit.thebaudeau@advansee.com>
> > Cc: Marek Vasut <marex@denx.de>
> > Cc: Stefano Babic <sbabic@denx.de>
> > ---
> 
> Hi Beno?t,
> 
> > Changes for v2: None.
> > 
> >  .../arch/arm/include/asm/arch-mx31/imx-regs.h      |   26
> >  --------------------
> >  .../include/usb/ehci-fsl.h                         |   22
> >  +++++++++++++++++
> >  2 files changed, 22 insertions(+), 26 deletions(-)
> > 
> 
> By applying this patchset I see several minor issues reported by
> checkpatch:
> 
> WARNING: line over 80 characters
> #303: FILE: drivers/usb/host/ehci-mx5.c:43:
> +#define MXC_OTG_UCTRL_OWIE_BIT		(1 << 27)	/* OTG wakeup intr enable
> */
> 
> WARNING: line over 80 characters
> #305: FILE: drivers/usb/host/ehci-mx5.c:45:
> +#define MXC_H1_UCTRL_H1UIE_BIT		(1 << 12)	/* Host1 ULPI interrupt
> enable */
> 
> WARNING: line over 80 characters
> #306: FILE: drivers/usb/host/ehci-mx5.c:46:
> +#define MXC_H1_UCTRL_H1WIE_BIT		(1 << 11)	/* HOST1 wakeup intr
> enable */
> 
> WARNING: line over 80 characters
> #312: FILE: drivers/usb/host/ehci-mx5.c:50:
> +#define MXC_OTG_PHYCTRL_OC_DIS_BIT	(1 << 8)	/* OTG Disable
> Overcurrent
> Event */
> 
> WARNING: line over 80 characters
> #313: FILE: drivers/usb/host/ehci-mx5.c:51:
> +#define MXC_H1_OC_DIS_BIT		(1 << 5)	/* UH1 Disable Overcurrent Event
> */
> 
> WARNING: line over 80 characters
> #343: FILE: drivers/usb/host/ehci-mx5.c:174:
> +			v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask unused */
> 
> WARNING: line over 80 characters
> #352: FILE: drivers/usb/host/ehci-mx5.c:190:
> +			v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask unused */
> 
> WARNING: line over 80 characters
> #641: FILE: drivers/usb/host/ehci-mx5.c:47:
> +#define MXC_OTG_UCTRL_O_PWR_POL_BIT	(1 << 24)	/* OTG power pin
> polarity */
> 
> WARNING: line over 80 characters
> #645: FILE: drivers/usb/host/ehci-mx5.c:51:
> +#define MXC_H1_UCTRL_H1_PWR_POL_BIT	(1 << 8)	/* HOST1 power pin
> polarity */
> 
> WARNING: line over 80 characters
> #648: FILE: drivers/usb/host/ehci-mx5.c:54:
> +#define MXC_OTG_PHYCTRL_OC_POL_BIT	(1 << 9)	/* OTG Polarity of
> Overcurrent */
> 
> WARNING: line over 80 characters
> #650: FILE: drivers/usb/host/ehci-mx5.c:56:
> +#define MXC_H1_OC_POL_BIT		(1 << 6)	/* UH1 Polarity of Overcurrent
> */
> 
> WARNING: line over 80 characters
> #652: FILE: drivers/usb/host/ehci-mx5.c:58:
> +#define MXC_OTG_PHYCTRL_PWR_POL_BIT	(1 << 3)	/* OTG Power Pin
> Polarity */
> 
> WARNING: line over 80 characters
> #873: FILE: drivers/usb/host/ehci-mxc.c:85:
> +			MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT |
> 
> WARNING: line over 80 characters
> #1078: FILE: drivers/usb/host/ehci-mxc.c:184:
> +			MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |
> 
> WARNING: line over 80 characters
> #1179: FILE: board/freescale/mx35pdk/mx35pdk.c:105:
> +	mxc_request_iomux(MX35_PIN_USBOTG_PWR, MUX_CONFIG_SION |
> MUX_CONFIG_FUNC);
> 
> WARNING: line over 80 characters
> #1180: FILE: board/freescale/mx35pdk/mx35pdk.c:106:
> +	mxc_request_iomux(MX35_PIN_USBOTG_OC, MUX_CONFIG_SION |
> MUX_CONFIG_FUNC);
> 
> total: 0 errors, 16 warnings, 810 lines checked
> 
> Can you fix them ? Thanks !

OK, I'll do that. For the #define-s, do you prefer that I move the comment to
the previous line, or that I split the end of the comment to the next line?

Best regards,
Beno?t