[U-Boot] [PATCH 6/8] rockchip: rk3188: Switch to new i2c IP blocks

[Heiko Stuebner <heiko@sntech.de>]

Am Samstag, 25. März 2017, 19:17:33 CEST schrieb Simon Glass:
> Hi Heiko,
> 
> On 24 March 2017 at 01:32, Heiko Stübner <heiko@sntech.de> wrote:
> > Am Donnerstag, 23. März 2017, 21:28:08 CET schrieb Simon Glass:
> >> Hi Heiko,
> >>
> >> On 20 March 2017 at 05:40, Heiko Stuebner <heiko@sntech.de> wrote:
> >> > The rk3066/rk3188 introduced new i2c IP blocks but kept the old ones
> >> > around just in case. The default also points to these old controllers.
> >> >
> >> > The "new" blocks proved stable and nobody ever used the old ones anywhere,
> >> > not in the kernel and not in U-Boot, so to be able to reuse the already
> >> > existing driver make the rk3188 switch to the new ones in U-Boot as well.
> >> >
> >> > Signed-off-by: Heiko Stuebner <heiko@sntech.de>
> >> > ---
> >> >
> >> >  arch/arm/mach-rockchip/rk3188-board-spl.c | 21 +++++++++++++++++++++
> >> >  1 file changed, 21 insertions(+)
> >> >
> >> > diff --git a/arch/arm/mach-rockchip/rk3188-board-spl.c
> >> > b/arch/arm/mach-rockchip/rk3188-board-spl.c index affd959f86..14847a7b1b
> >> > 100644
> >> > --- a/arch/arm/mach-rockchip/rk3188-board-spl.c
> >> > +++ b/arch/arm/mach-rockchip/rk3188-board-spl.c
> >> > @@ -17,6 +17,7 @@
> >> >
> >> >  #include <asm/io.h>
> >> >  #include <asm/arch/bootrom.h>
> >> >  #include <asm/arch/clock.h>
> >> >
> >> > +#include <asm/arch/grf_rk3188.h>
> >> >
> >> >  #include <asm/arch/hardware.h>
> >> >  #include <asm/arch/periph.h>
> >> >  #include <asm/arch/pmu_rk3188.h>
> >> >
> >> > @@ -102,6 +103,7 @@ void board_init_f(ulong dummy)
> >> >
> >> >  {
> >> >
> >> >         struct udevice *pinctrl, *dev;
> >> >         struct rk3188_pmu *pmu;
> >> >
> >> > +       struct rk3188_grf *grf;
> >> >
> >> >         int ret;
> >> >
> >> >         /* Example code showing how to enable the debug UART on RK3188 */
> >> >
> >> > @@ -154,6 +156,25 @@ void board_init_f(ulong dummy)
> >> >
> >> >                 error("pmu syscon returned %ld\n", PTR_ERR(pmu));
> >> >
> >> >         SAVE_SP_ADDR = readl(&pmu->sys_reg[2]);
> >> >
> >> > +       /* init common grf settings */
> >> > +       grf = syscon_get_first_range(ROCKCHIP_SYSCON_GRF);
> >> > +       if (IS_ERR(grf)) {
> >> > +               error("grf syscon returned %ld\n", PTR_ERR(grf));
> >> > +       } else {
> >> > +               /* make i2c controllers use the new IP */
> >> > +               rk_clrsetreg(&grf->soc_con1,
> >> > +                       RKI2C4_SEL_MASK << RKI2C4_SEL_SHIFT |
> >> > +                       RKI2C3_SEL_MASK << RKI2C3_SEL_SHIFT |
> >> > +                       RKI2C2_SEL_MASK << RKI2C2_SEL_SHIFT |
> >> > +                       RKI2C1_SEL_MASK << RKI2C1_SEL_SHIFT |
> >> > +                       RKI2C0_SEL_MASK << RKI2C0_SEL_SHIFT,
> >> > +                       RKI2C4_SEL_MASK << RKI2C4_SEL_SHIFT |
> >> > +                       RKI2C3_SEL_MASK << RKI2C3_SEL_SHIFT |
> >> > +                       RKI2C2_SEL_MASK << RKI2C2_SEL_SHIFT |
> >> > +                       RKI2C1_SEL_MASK << RKI2C1_SEL_SHIFT |
> >> > +                       RKI2C0_SEL_MASK << RKI2C0_SEL_SHIFT);
> >> > +       }
> >>
> >> Can you move this to the pinctrl driver?
> >
> > Are you sure that is the right approach?
> >
> > This setting switches the i2c controller IP block used, while the i2c-pins are
> > not affected by this at all. You could also use the i2c pins with the other
> > i2c controller with the same pinctrl settings, so it feels a tiny bit strange
> > to burden the pinctrl driver with this.
> 
> It still seems like pinctrl to me, in that you are selecting which IP
> block uses those pins. If you don't want it in pinctrl, perhaps this
> whole thing should go in the I2C driver?

no pinctrl is fine, and funnily enough, when I tried moving that there,
I realized that the pinctrl driver had the switch to the new controller
right from the beginning and I just had forgotten about it :-S, see the

	/* enable new i2c controller */
	rk_clrsetreg(&grf->soc_con1, 1 << RKI2C0_SEL_SHIFT,
				     1 << RKI2C0_SEL_SHIFT);

parts in pinctrl_rk3188.c .

So it looks like we can just drop this patch altogether :-) .


Heiko