* [U-Boot-Users] MPC8266 Abatron config file
@ 2003-12-02 19:30 Allen Curtis
2003-12-02 20:13 ` Wolfgang Denk
0 siblings, 1 reply; 3+ messages in thread
From: Allen Curtis @ 2003-12-02 19:30 UTC (permalink / raw)
To: u-boot
Does anyone have a configuration file which works with u=boot? I have a file
which is good enough to communicate with the board and program the flash.
However when I try to run u-boot (type go), the baud rate is not correct. It
appears that it is 4X the configured rate. If I remove the Abatron and boot
normally, everything works fine.
TIA
--
All things come to those who wait. Some of us just have to wait a little
longer...
^ permalink raw reply [flat|nested] 3+ messages in thread
* [U-Boot-Users] MPC8266 Abatron config file
2003-12-02 19:30 [U-Boot-Users] MPC8266 Abatron config file Allen Curtis
@ 2003-12-02 20:13 ` Wolfgang Denk
2003-12-03 2:23 ` Allen Curtis
0 siblings, 1 reply; 3+ messages in thread
From: Wolfgang Denk @ 2003-12-02 20:13 UTC (permalink / raw)
To: u-boot
In message <200312021130.26182.acurtis@onz.com> you wrote:
> Does anyone have a configuration file which works with u=boot? I have a file
> which is good enough to communicate with the board and program the flash.
> However when I try to run u-boot (type go), the baud rate is not correct. It
> appears that it is 4X the configured rate. If I remove the Abatron and boot
> normally, everything works fine.
Well, this is a setting which is definitely hardware (board) depen-
dend. So if you don't give away any facts about your hardware it is
impossible to help (actually it's probably impossible in general as
this might be a custom board).
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: wd at denx.de
Every program has at least one bug and can be shortened by at least
one instruction - from which, by induction, one can deduce that every
program can be reduced to one instruction which doesn't work.
^ permalink raw reply [flat|nested] 3+ messages in thread
* [U-Boot-Users] MPC8266 Abatron config file
2003-12-02 20:13 ` Wolfgang Denk
@ 2003-12-03 2:23 ` Allen Curtis
0 siblings, 0 replies; 3+ messages in thread
From: Allen Curtis @ 2003-12-03 2:23 UTC (permalink / raw)
To: u-boot
This is a standard ADS8266 board. The MPC8266 configuration file I am using
has been posted to this list, although I do not see it on your FTP site.
Essentially it is the same at the MPC8260 version that is on the site.
On Tuesday 02 December 2003 12:13 pm, Wolfgang Denk wrote:
> In message <200312021130.26182.acurtis@onz.com> you wrote:
> > Does anyone have a configuration file which works with u=boot? I have a
> > file which is good enough to communicate with the board and program the
> > flash. However when I try to run u-boot (type go), the baud rate is not
> > correct. It appears that it is 4X the configured rate. If I remove the
> > Abatron and boot normally, everything works fine.
>
> Well, this is a setting which is definitely hardware (board) depen-
> dend. So if you don't give away any facts about your hardware it is
> impossible to help (actually it's probably impossible in general as
> this might be a custom board).
>
>
> Best regards,
>
> Wolfgang Denk
--
All things come to those who wait. Some of us just have to wait a little
longer...
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2003-12-03 2:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-12-02 19:30 [U-Boot-Users] MPC8266 Abatron config file Allen Curtis
2003-12-02 20:13 ` Wolfgang Denk
2003-12-03 2:23 ` Allen Curtis
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox