public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: Ladislav Michl <ladis@linux-mips.org>
To: u-boot@lists.denx.de
Subject: [U-Boot-Users] [PATCH] Update VoiceBlue to use new MTD flash partitioning methods
Date: Tue, 16 Aug 2005 12:07:51 +0200	[thread overview]
Message-ID: <20050816100751.GA22043@orphique> (raw)
In-Reply-To: <20050807230847.D54D9352BD9@atlas.denx.de>

On Mon, Aug 08, 2005 at 01:08:47AM +0200, Wolfgang Denk wrote:
> Among the modified and not tested targets there is a group of targets
> which were implementing their custom multi-partition scheme. This was
> mostly duplicating jffs2_part_info() routine  code.  Introducing  the
> new  common  scheme  required removing this duplicated code, so those
> targets should be especially carefully  tested  by  the  board  main-
> tainers.  Target  list  that  require  special  attention:  xsengine,
> voiceblue, ...

Hi Wolfgang,

support for VoiceBlue board is broken in 1.1.3, because it needs
partitions (well, my fault. I shouldn't be on holidays ;-)). Patch below
fixes that (and a bit more).

Best regards,
	ladis

CHANGELOG
* VoiceBlue update: use new MTD flash partitioning methods, use more
  reasonable TEXT_BASE, update default environment and enable keyed
  autoboot.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

diff --git a/board/voiceblue/config.mk b/board/voiceblue/config.mk
--- a/board/voiceblue/config.mk
+++ b/board/voiceblue/config.mk
@@ -12,5 +12,5 @@ ifeq ($(VOICEBLUE_SMALL_FLASH),y)
 TEXT_BASE = 0x20012000
 else
 # Running in SDRAM...
-TEXT_BASE = 0x13000000
+TEXT_BASE = 0x13FD0000
 endif
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -47,6 +47,8 @@
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
 /*
  * Physical Memory Map
  */
@@ -94,7 +96,6 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#define CFG_JFFS_CUSTOM_PART	/* see board/voiceblue/jffs2parts.c */
 #endif
 
 /*
@@ -104,9 +105,11 @@
 #ifdef VOICEBLUE_SMALL_FLASH
 #define CFG_MALLOC_LEN		(SZ_64K - CFG_GBL_DATA_SIZE)
 #define CONFIG_STACKSIZE	SZ_8K
+#define PHYS_SDRAM_1_RESERVED	0
 #else
 #define CFG_MALLOC_LEN		SZ_4M
 #define CONFIG_STACKSIZE	SZ_1M
+#define PHYS_SDRAM_1_RESERVED	(CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE)
 #endif
 
 /*
@@ -174,6 +177,7 @@
 #define CONFIG_BOOTCOMMAND	"run nboot"
 #define CONFIG_PREBOOT		"run setup"
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"silent=1\0"						\
 	"ospart=0\0"						\
 	"swapos=no\0"						\
 	"setpart="						\
@@ -185,15 +189,37 @@
 	"fi\0"							\
 	"setup=setenv bootargs console=ttyS0,$baudrate "	\
 		"mtdparts=$mtdparts\0"				\
-	"nfsargs=run setpart; setenv bootargs $bootargs "	\
-		"root=/dev/nfs ip=dhcp\0"			\
+	"nfsargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
+		"nfsroot=$rootpath root=/dev/nfs\0"		\
 	"flashargs=run setpart; setenv bootargs $bootargs "	\
 		"root=/dev/mtdblock$partition ro "		\
 		"rootfstype=jffs2\0"				\
-	"nboot=run nfsargs; bootp; tftp; bootm\0"		\
-	"fboot=run flashargs; fsload /boot/uImage; bootm\0"
+	"initrdargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
+	"fboot=run flashargs; fsload /boot/uImage; bootm\0"	\
+	"iboot=bootp; run initrdargs; tftp; bootm\0"		\
+	"nboot=bootp; run nfsargs; tftp; bootm\0"
 #endif
 
+#ifndef VOICEBLUE_SMALL_FLASH
+#define CONFIG_SILENT_CONSOLE		1	/* enable silent startup */
+
+#if 1	/* feel free to disable for development */
+#define CONFIG_AUTOBOOT_KEYED		/* Enable password protection	*/
+#define CONFIG_AUTOBOOT_PROMPT	"\nVoiceBlue Enterprise - booting...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"."	/* 1st "password"	*/
+#endif
+
+/*
+ * JFFS2 partitions (mtdparts command line support)
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=omapflash.0"
+#define MTDPARTS_DEFAULT	"mtdparts=omapflash.0:128k(uboot),64k(env),64k(r_env),16256k(data1),-(data2)"
+
+#endif	/* VOICEBLUE_SMALL_FLASH */
+
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
@@ -213,7 +239,7 @@
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	PHYS_SDRAM_1
-#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE
+#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
 
 #undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 
@@ -247,22 +273,4 @@
 
 #define VOICEBLUE_LED_REG	0x04030000
 
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00040000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=voiceblue-0"
-#define MTDPARTS_DEFAULT	"mtdparts=voiceblue-0:128k(uboot),64k(env),64k(renv),-(jffs2)"
-*/
-
 #endif	/* __CONFIG_H */

  reply	other threads:[~2005-08-16 10:07 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2005-08-07 23:08 [U-Boot-Users] NOTE: New MTD flash partitioning methods Wolfgang Denk
2005-08-16 10:07 ` Ladislav Michl [this message]
2006-06-19 22:15   ` [U-Boot-Users] [PATCH] Update VoiceBlue to use new " Wolfgang Denk

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20050816100751.GA22043@orphique \
    --to=ladis@linux-mips.org \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox