From mboxrd@z Thu Jan 1 00:00:00 1970 From: Matthias Fuchs Date: Fri, 28 Dec 2007 11:56:23 +0100 Subject: [U-Boot-Users] [PATCH 3/3 RESEND] ppc4xx: Complete PMC440 board support Message-ID: <200712281156.23522.matthias.fuchs@esd-electronics.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de This patch brings the PMC440 board configuration file. Finally it enables the PMC440 board support. Signed-off-by: Matthias Fuchs --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 + include/configs/{sequoia.h => PMC440.h} | 418 ++++++++++++++++--------------- 4 files changed, 227 insertions(+), 196 deletions(-) copy include/configs/{sequoia.h => PMC440.h} (51%) diff --git a/MAINTAINERS b/MAINTAINERS index d6b1882..abaee54 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -158,6 +158,7 @@ Matthias Fuchs PCI405 PPC405GP PLU405 PPC405EP PMC405 PPC405GP + PMC440 PPC440EPx VOH405 PPC405EP VOM405 PPC405EP WUH405 PPC405EP diff --git a/MAKEALL b/MAKEALL index 975f4b3..9d5b60d 100755 --- a/MAKEALL +++ b/MAKEALL @@ -207,6 +207,7 @@ LIST_4xx=" \ PIP405 \ PLU405 \ PMC405 \ + PMC440 \ PPChameleonEVB \ rainier \ sbc405 \ diff --git a/Makefile b/Makefile index a049198..c23b50a 100644 --- a/Makefile +++ b/Makefile @@ -1280,6 +1280,9 @@ PLU405_config: unconfig PMC405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx pmc405 esd +PMC440_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx pmc440 esd + PPChameleonEVB_config \ PPChameleonEVB_BA_25_config \ PPChameleonEVB_ME_25_config \ diff --git a/include/configs/sequoia.h b/include/configs/PMC440.h similarity index 51% copy from include/configs/sequoia.h copy to include/configs/PMC440.h index 1f72b54..3d2ed1e 100644 --- a/include/configs/sequoia.h +++ b/include/configs/PMC440.h @@ -1,4 +1,8 @@ /* + * (C) Copyright 2007 + * Matthias Fuchs, esd gmbh, matthias.fuchs at esd-electronics.com. + * Based on the sequoia configuration file. + * * (C) Copyright 2006-2007 * Stefan Roese, DENX Software Engineering, sr at denx.de. * @@ -23,7 +27,7 @@ */ /************************************************************************ - * sequoia.h - configuration for Sequoia & Rainier boards + * PMC440.h - configuration for esd PMC440 boards ***********************************************************************/ #ifndef __CONFIG_H #define __CONFIG_H @@ -31,75 +35,66 @@ /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ -/* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */ -#ifndef CONFIG_RAINIER -#define CONFIG_440EPX 1 /* Specific PPC440EPx */ -#else -#define CONFIG_440GRX 1 /* Specific PPC440GRx */ -#endif -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_4xx 1 /* ... PPC4xx family */ -/* Detect Sequoia PLL input clock automatically via CPLD bit */ -#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ - 33333333 : 33000000) +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ -#if 0 -/* - * 44x dcache supported is working now on sequoia, but we don't enable - * it yet since it needs further testing - */ -#define CONFIG_4xx_DCACHE /* enable dcache */ -#endif +#define CONFIG_SYS_CLK_FREQ 33333400 -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_4xx_DCACHE /* enable dcache */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_BOARD_TYPES 1 /* support board types */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */ + +#define CONFIG_PRAM 0 /* use pram variable to overwrite */ #define CFG_BOOT_BASE_ADDR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ #define CFG_MONITOR_BASE TEXT_BASE -#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ -#define CFG_OCM_BASE 0xe0010000 /* ocm */ +#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ +#define CFG_OCM_BASE 0xe0010000 /* ocm */ #define CFG_OCM_DATA_ADDR CFG_OCM_BASE -#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 #define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 #define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 +#define CFG_PCI_MEMSIZE 0x80000000 /* 2GB! */ /* Don't change either of these */ -#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ #define CFG_USB2D0_BASE 0xe0000100 #define CFG_USB_DEVICE 0xe0000000 #define CFG_USB_HOST 0xe0000400 -#define CFG_BCSR_BASE 0xc0000000 +#define CFG_FPGA_BASE0 0xef000000 /* 32 bit */ +#define CFG_FPGA_BASE1 0xef100000 /* 16 bit */ /*----------------------------------------------------------------------- * Initial RAM & stack pointer *----------------------------------------------------------------------*/ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ +#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ #define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#undef CFG_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 -/* define this if you want console on UART1 */ -#undef CONFIG_UART1_CONSOLE +#define CONFIG_SERIAL_MULTI 1 +#undef CONFIG_UART1_CONSOLE /* console on front panel */ #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} @@ -108,42 +103,52 @@ * Environment *----------------------------------------------------------------------*/ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CFG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */ #else -#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ #define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ #endif /*----------------------------------------------------------------------- + * RTC + *----------------------------------------------------------------------*/ +#define CONFIG_RTC_RX8025 + +/*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ #define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_OFFSET 0 /* environment starts@the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */ +#endif + /* * IPL (Initial Program Loader, integrated inside CPU) * Will load first 4k from NAND (SPL) into cache and execute it from there. @@ -162,27 +167,27 @@ * set up. While still running from cache, I experienced problems accessing * the NAND controller. sr - 2006-08-25 */ -#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ #define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) /* * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) */ -#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ /* * Now the NAND chip has to be defined (no autodetection used!) */ -#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ #define CFG_NAND_ECCSIZE 256 #define CFG_NAND_ECCBYTES 3 @@ -204,139 +209,129 @@ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#define CFG_MBYTES_SDRAM (256) /* 256MB */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ #endif /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F +#define CONFIG_I2C_CMD_TREE 1 +#define CONFIG_I2C_MULTI_BUS 1 + #define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 + +#define CFG_I2C_EEPROM_ADDR 0x54 +#define CFG_I2C_EEPROM_ADDR_LEN 2 #define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01 + +#define CFG_EEPROM_WREN 1 +#define CFG_I2C_BOOT_EEPROM_ADDR 0x52 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +/* + * standard dtt sensor configuration - bottom bit will determine local or + * remote sensor of the TMP401 + */ +#define CONFIG_DTT_SENSORS { 0, 1 } + +/* + * The PMC440 uses a TI TMP401 temperature sensor. This part + * is basically compatible to the ADM1021 that is supported + * by U-Boot. + * + * - i2c addr 0x4c + * - conversion rate 0x02 = 0.25 conversions/second + * - ALERT ouput disabled + * - local temp sensor enabled, min set to 0 deg, max set to 70 deg + * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg + */ +#define CONFIG_DTT_ADM1021 +#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" +#define CONFIG_PREBOOT /* enable preboot variable */ #undef CONFIG_BOOTARGS /* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_RAINIER -#define CONFIG_HOSTNAME sequoia -#define CFG_BOOTFILE "bootfile=/tftpboot/sequoia/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME rainier -#define CFG_BOOTFILE "bootfile=/tftpboot/rainier/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif +#define CONFIG_HOSTNAME pmc440 +#define CFG_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" +#define CFG_ROOTPATH "rootpath=/opt/eldk_410/ppc_4xx\0" -#define CONFIG_EXTRA_ENV_SETTINGS \ +#define CONFIG_EXTRA_ENV_SETTINGS \ CFG_BOOTFILE \ CFG_ROOTPATH \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ + "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ + "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ + "bootm\0" \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ + "load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \ "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 200000 FFFA0000 60000\0" \ - "upd=run load;run update\0" \ + "cp.b 200000 FFFA0000 60000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_M88E1111_PHY 1 -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_HAS_ETH0 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_NET_MULTI 1 -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 1 +#define CONFIG_RESET_PHY_R 1 /* USB */ -#ifdef CONFIG_440EPX #define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE #define CFG_OHCI_BE_CONTROLLER -#undef CFG_USB_OHCI_BOARD_INIT +#define CFG_USB_OHCI_BOARD_INIT 1 #define CFG_USB_OHCI_CPU_INIT 1 #define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST #define CFG_USB_OHCI_SLOT_NAME "ppc440" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE -#endif /* CONFIG_440EPX */ - /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_ISO_PARTITION - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - - -/* - * Command line configuration. - */ #include +#define CONFIG_CMD_BSP +#define CONFIG_CMD_DATE #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT @@ -352,81 +347,100 @@ #define CONFIG_CMD_NFS #define CONFIG_CMD_PCI #define CONFIG_CMD_PING +#define CONFIG_CMD_USB #define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -#ifdef CONFIG_440EPX -#define CONFIG_CMD_USB -#endif - -#ifndef CONFIG_RAINIER -#define CFG_POST_FPU_ON CFG_POST_FPU -#else -#define CFG_POST_FPU_ON 0 -#endif - /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_I2C | \ - CFG_POST_CACHE | \ - CFG_POST_FPU_ON | \ - CFG_POST_ETHER | \ +/* ethernet POST sometimes freezes the CPU. + * So disable it for now until issue is solved + */ +#if 0 +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_UART | \ + CFG_POST_I2C | \ + CFG_POST_CACHE | \ + CFG_POST_FPU | \ + CFG_POST_ETHER | \ + CFG_POST_SPR) +#else +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_UART | \ + CFG_POST_I2C | \ + CFG_POST_CACHE | \ + CFG_POST_FPU | \ CFG_POST_SPR) +#endif #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) + +/* esd expects pram at end of physical memory. + * So no logbuffer at the moment. + */ +#if 0 #define CONFIG_LOGBUFFER -#define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ +#endif +#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ -#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ #define CONFIG_SUPPORT_VFAT /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n" +#undef CONFIG_AUTOBOOT_DELAY_STR +#define CONFIG_AUTOBOOT_STOP_STR " " + /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ /* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ /* Board-specific PCI */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +/* PCI identification */ +#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */ +#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */ +#define CFG_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC +#define CFG_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST /* * For booting Linux, the board info and command line data @@ -436,6 +450,15 @@ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- + * FPGA stuff + *----------------------------------------------------------------------*/ +#define CONFIG_FPGA +#define CONFIG_FPGA_XILINX +#define CONFIG_FPGA_SPARTAN2 +#define CONFIG_FPGA_SPARTAN3 + +#define CONFIG_FPGA_COUNT 2 +/*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -443,30 +466,33 @@ * On Sequoia CS0 and CS3 are switched when configuring for NAND booting */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CFG_NAND_CS 3 /* NAND chip connected to CSx */ -/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_NAND_CS 2 /* NAND chip connected to CSx */ + +/* Memory Bank 0 (NOR-FLASH) initialization */ #define CFG_EBC_PB0AP 0x03017200 #define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000) -/* Memory Bank 3 (NAND-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x018003c0 -#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000) +/* Memory Bank 2 (NAND-FLASH) initialization */ +#define CFG_EBC_PB2AP 0x018003c0 +#define CFG_EBC_PB2CR (CFG_NAND_ADDR | 0x1c000) #else -#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ -/* Memory Bank 3 (NOR-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x03017200 -#define CFG_EBC_PB3CR (CFG_FLASH_BASE | 0xda000) +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 2 (NOR-FLASH) initialization */ +#define CFG_EBC_PB2AP 0x03017200 +#define CFG_EBC_PB2CR (CFG_FLASH_BASE | 0xda000) -/* Memory Bank 0 (NAND-FLASH) initialization */ +/* Memory Bank 0 (NAND-FLASH) initialization */ #define CFG_EBC_PB0AP 0x018003c0 #define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) #endif -/* Memory Bank 2 (CPLD) initialization */ -#define CFG_EBC_PB2AP 0x24814580 -#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x38000) +/* Memory Bank 4 (FPGA / 32Bit) initialization */ +#define CFG_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */ +#define CFG_EBC_PB4CR (CFG_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */ -#define CFG_BCSR5_PCI66EN 0x80 +/* Memory Bank 5 (FPGA / 16Bit) initialization */ +#define CFG_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */ +#define CFG_EBC_PB5CR (CFG_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */ /*----------------------------------------------------------------------- * NAND FLASH @@ -474,23 +500,23 @@ #define CFG_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) -#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ /* * Internal Definitions * * Boot Flags */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ -#if defined(CONFIG_CMD_KGDB) +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -#endif /* __CONFIG_H */ +#endif /* __CONFIG_H */ -- 1.5.3