* [U-Boot-Users] Pull request: u-boot-ixp
@ 2008-01-08 21:22 Jean-Christophe PLAGNIOL-VILLARD
2008-01-09 10:56 ` Wolfgang Denk
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-01-08 21:22 UTC (permalink / raw)
To: u-boot
Please pull u-boot-ixp
The following changes since commit 74ac5facb988fc488a707db228b177ead63a6541:
Wolfgang Denk (1):
Merge branch 'inka4x0-ng' of /home/m8/git/u-boot/
are available in the git repository at:
git://denx.de/git/u-boot-ixp.git master
Jean-Christophe PLAGNIOL-VILLARD (4):
Add missing file in gitignore and comments
IXP: Add full baud-rate support for ixp42x, ixp45x and ixp46x
ARM: support board-specific ethernet PHY init
Allow CONFIG_AUTO_COMPLETE and command history CONFIG_CMDLINE_EDITING at the sametime
Michael Schwingen (1):
PATCH: load ixp42x NPE firmware from separate flash block, remove dead code
.gitignore | 32 ++++++++++++++++++++++++++++++--
common/main.c | 26 ++++++++++++++++++++++++--
cpu/ixp/npe/IxNpeDl.c | 2 ++
cpu/ixp/npe/IxNpeDlImageMgr.c | 12 ++++++++----
cpu/ixp/serial.c | 24 ++++++++++--------------
include/.gitignore | 1 +
lib_arm/board.c | 4 ++++
7 files changed, 79 insertions(+), 22 deletions(-)
Best Regards,
J.
^ permalink raw reply [flat|nested] 4+ messages in thread* [U-Boot-Users] Pull request: u-boot-ixp
2008-01-08 21:22 [U-Boot-Users] Pull request: u-boot-ixp Jean-Christophe PLAGNIOL-VILLARD
@ 2008-01-09 10:56 ` Wolfgang Denk
2008-01-09 12:25 ` Jean-Christophe PLAGNIOL-VILLARD
2008-01-18 0:24 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 2 replies; 4+ messages in thread
From: Wolfgang Denk @ 2008-01-09 10:56 UTC (permalink / raw)
To: u-boot
Dear Jean-Christophe,
in message <20080108212200.GD674@game.jcrosoft.org> you wrote:
>
> The following changes since commit 74ac5facb988fc488a707db228b177ead63a6541:
> Wolfgang Denk (1):
> Merge branch 'inka4x0-ng' of /home/m8/git/u-boot/
>
> are available in the git repository at:
>
> git://denx.de/git/u-boot-ixp.git master
Sorry, but I just had to reject some of the patches you merged.
I apologize for not catching this earlier.
> Jean-Christophe PLAGNIOL-VILLARD (4):
> Add missing file in gitignore and comments
> IXP: Add full baud-rate support for ixp42x, ixp45x and ixp46x
> ARM: support board-specific ethernet PHY init
> Allow CONFIG_AUTO_COMPLETE and command history CONFIG_CMDLINE_EDITING at the sametime
I merged those.
> Michael Schwingen (1):
> PATCH: load ixp42x NPE firmware from separate flash block, remove dead code
This was the one I skipped, as it *adds* dead code (in "#if 0" /
"#endif" constructs) instead of removing it as the subject promises.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
There is an old custom among my people. When a woman saves a man's
life, he is grateful.
-- Nona, the Kanuto which woman, "A Private Little War",
stardate 4211.8.
^ permalink raw reply [flat|nested] 4+ messages in thread
* [U-Boot-Users] Pull request: u-boot-ixp
2008-01-09 10:56 ` Wolfgang Denk
@ 2008-01-09 12:25 ` Jean-Christophe PLAGNIOL-VILLARD
2008-01-18 0:24 ` Jean-Christophe PLAGNIOL-VILLARD
1 sibling, 0 replies; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-01-09 12:25 UTC (permalink / raw)
To: u-boot
On 11:56 Wed 09 Jan , Wolfgang Denk wrote:
> Dear Jean-Christophe,
>
> in message <20080108212200.GD674@game.jcrosoft.org> you wrote:
> >
> > The following changes since commit 74ac5facb988fc488a707db228b177ead63a6541:
> > Wolfgang Denk (1):
> > Merge branch 'inka4x0-ng' of /home/m8/git/u-boot/
> >
> > are available in the git repository at:
> >
> > git://denx.de/git/u-boot-ixp.git master
>
> Sorry, but I just had to reject some of the patches you merged.
>
> I apologize for not catching this earlier.
>
>
> > Jean-Christophe PLAGNIOL-VILLARD (4):
> > Add missing file in gitignore and comments
> > IXP: Add full baud-rate support for ixp42x, ixp45x and ixp46x
> > ARM: support board-specific ethernet PHY init
> > Allow CONFIG_AUTO_COMPLETE and command history CONFIG_CMDLINE_EDITING at the sametime
>
> I merged those.
>
> > Michael Schwingen (1):
> > PATCH: load ixp42x NPE firmware from separate flash block, remove dead code
>
> This was the one I skipped, as it *adds* dead code (in "#if 0" /
> "#endif" constructs) instead of removing it as the subject promises.
I will fix this and add an other patch to allow to load the NPE firmware
from flash and ram
Best Regards,
J.
^ permalink raw reply [flat|nested] 4+ messages in thread
* [U-Boot-Users] Pull request: u-boot-ixp
2008-01-09 10:56 ` Wolfgang Denk
2008-01-09 12:25 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2008-01-18 0:24 ` Jean-Christophe PLAGNIOL-VILLARD
1 sibling, 0 replies; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-01-18 0:24 UTC (permalink / raw)
To: u-boot
The following changes since commit f188896c2f1594fe749fdb99bbc8c54023cfab3a:
Wolfgang Denk (1):
Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/master
are available in the git repository at:
git://www.denx.de/git/u-boot-ixp.git master
Jean-Christophe PLAGNIOL-VILLARD (2):
IXP: add dynamic microcode addr
ARM: remove useless function board_post_init
Michael Schwingen (7):
load ixp42x NPE firmware from separate flash block, remove dead code
IXP: enable RTS
add AcTux-1 board support
add AcTux-2 board support
add AcTux-3 board support
add AcTux-4 board support
Add AcTux board support
MAINTAINERS | 7 +
MAKEALL | 4 +
Makefile | 12 +
README | 3 +
board/actux1/Makefile | 50 +
board/actux1/actux1.c | 161 +++
board/actux1/actux1_hw.h | 57 +
board/actux1/config.mk | 4 +
board/actux1/u-boot.lds | 69 +
board/actux2/Makefile | 50 +
board/actux2/actux2.c | 134 ++
board/actux2/actux2_hw.h | 59 +
board/actux2/config.mk | 4 +
board/actux2/u-boot.lds | 74 +
board/actux3/Makefile | 50 +
board/actux3/actux3.c | 165 +++
board/actux3/actux3_hw.h | 60 +
board/actux3/config.mk | 4 +
board/actux3/u-boot.lds | 74 +
board/actux4/Makefile | 50 +
board/actux4/actux4.c | 132 ++
board/actux4/actux4_hw.h | 49 +
board/actux4/config.mk | 4 +
board/actux4/u-boot.lds | 65 +
board/ixdp425/ixdp425.c | 5 -
board/prodrive/pdnb3/pdnb3.c | 5 -
board/xm250/xm250.c | 8 -
cpu/ixp/npe/IxNpeDl.c | 32 -
cpu/ixp/npe/IxNpeDlImageMgr.c | 37 +-
cpu/ixp/npe/Makefile | 4 +-
cpu/ixp/serial.c | 6 +-
include/asm-arm/mach-types.h | 3121 ++++++++++++++++++++++++++++++++++++++++-
include/configs/actux1.h | 247 ++++
include/configs/actux2.h | 224 +++
include/configs/actux3.h | 224 +++
include/configs/actux4.h | 218 +++
36 files changed, 5362 insertions(+), 110 deletions(-)
create mode 100644 board/actux1/Makefile
create mode 100644 board/actux1/actux1.c
create mode 100644 board/actux1/actux1_hw.h
create mode 100644 board/actux1/config.mk
create mode 100644 board/actux1/u-boot.lds
create mode 100644 board/actux2/Makefile
create mode 100644 board/actux2/actux2.c
create mode 100644 board/actux2/actux2_hw.h
create mode 100644 board/actux2/config.mk
create mode 100644 board/actux2/u-boot.lds
create mode 100644 board/actux3/Makefile
create mode 100644 board/actux3/actux3.c
create mode 100644 board/actux3/actux3_hw.h
create mode 100644 board/actux3/config.mk
create mode 100644 board/actux3/u-boot.lds
create mode 100644 board/actux4/Makefile
create mode 100644 board/actux4/actux4.c
create mode 100644 board/actux4/actux4_hw.h
create mode 100644 board/actux4/config.mk
create mode 100644 board/actux4/u-boot.lds
create mode 100644 include/configs/actux1.h
create mode 100644 include/configs/actux2.h
create mode 100644 include/configs/actux3.h
create mode 100644 include/configs/actux4.h
Best Regards,
J.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-01-18 0:24 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-01-08 21:22 [U-Boot-Users] Pull request: u-boot-ixp Jean-Christophe PLAGNIOL-VILLARD
2008-01-09 10:56 ` Wolfgang Denk
2008-01-09 12:25 ` Jean-Christophe PLAGNIOL-VILLARD
2008-01-18 0:24 ` Jean-Christophe PLAGNIOL-VILLARD
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox