public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
* [U-Boot-Users] [PATCH] Add Fujitsu CoralP/Lime video driver
@ 2007-09-24 19:00 Anatolij Gustschin
  2008-01-09  8:05 ` Wolfgang Denk
  0 siblings, 1 reply; 5+ messages in thread
From: Anatolij Gustschin @ 2007-09-24 19:00 UTC (permalink / raw)
  To: u-boot


Add Fujitsu CoralP/Lime video driver and also
fix video console newline and carriage return
handling.

This driver is known to work with Fujitsu CoralP
PCI Eval. Board on sequoia board. It also works
with lwmon5 board.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
  drivers/Makefile      |    2
  drivers/cfb_console.c |   60 +++++++
  drivers/mb862xx.c     |  423 +++++++++++++++++++++++++++++++++++++++++++++++++
  include/mb862xx.h     |   44 +++++
  4 files changed, 526 insertions(+), 3 deletions(-)

diff --git a/drivers/Makefile b/drivers/Makefile
index 6bf05cc..74edf2d 100755
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -32,7 +32,7 @@ COBJS	= 3c589.o 5701rls.o ali512x.o at45
  	  cs8900.o ct69000.o dataflash.o dc2114x.o dm9000x.o \
  	  e1000.o eepro100.o enc28j60.o \
  	  i8042.o inca-ip_sw.o isp116x-hcd.o keyboard.o \
-	  lan91c96.o macb.o \
+	  lan91c96.o macb.o mb862xx.o \
  	  natsemi.o ne2000.o netarm_eth.o netconsole.o \
  	  ns16550.o ns8382x.o ns87308.o ns7520_eth.o omap1510_i2c.o \
  	  omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o \
diff --git a/drivers/cfb_console.c b/drivers/cfb_console.c
index bcf8771..47fda60 100644
--- a/drivers/cfb_console.c
+++ b/drivers/cfb_console.c
@@ -141,6 +141,18 @@ #endif
  #endif

  /*****************************************************************************/
+/* Defines for the MB862xx driver					     */
+/*****************************************************************************/
+#ifdef CONFIG_VIDEO_MB862xx
+
+#ifdef CONFIG_VIDEO_CORALP
+#define VIDEO_FB_LITTLE_ENDIAN
+#endif
+#define VIDEO_HW_RECTFILL
+#define VIDEO_HW_BITBLT
+#endif
+
+/*****************************************************************************/
  /* Include video_fb.h after definitions of VIDEO_HW_RECTFILL etc	     */
  /*****************************************************************************/
  #include <video_fb.h>
@@ -304,7 +316,11 @@ #define SHORTSWAP32(x)	 ((((x) & 0x00000
  #else
  #define SWAP16(x)	 (x)
  #define SWAP32(x)	 (x)
+#if !defined(VIDEO_FB_16BPP_PIXEL_SWAP)
  #define SHORTSWAP32(x)	 (x)
+#else
+#define SHORTSWAP32(x)	 ( ((x) >> 16) | ((x) << 16) )
+#endif
  #endif

  #if defined(DEBUG) || defined(DEBUG_CFB_CONSOLE)
@@ -647,7 +663,13 @@ static void console_back (void)

  static void console_newline (void)
  {
-	CURSOR_OFF console_row++;
+	/* Check if last character in the line was just drawn. If so, cursor was
+	   overwriten and need not to be cleared. Cursor clearing without this
+	   check causes overwriting the 1st character of the line
+	*/
+	if (console_col < CONSOLE_COLS)
+		CURSOR_OFF
+	console_row++;
  	console_col = 0;

  	/* Check if we need to scroll the terminal */
@@ -662,10 +684,18 @@ static void console_newline (void)

  /*****************************************************************************/

+static void console_cr (void)
+{
+	CURSOR_OFF console_col = 0;
+}
+
+/*****************************************************************************/
+
  void video_putc (const char c)
  {
  	switch (c) {
-	case 13:		/* ignore */
+	case 13:		/* back to first column */
+		console_cr ();
  		break;

  	case '\n':		/* next line */
@@ -716,10 +746,24 @@ #define FILL_8BIT_332RGB(r,g,b)	{			\
  	fb ++;						\
  }

+#if !defined(VIDEO_FB_16BPP_PIXEL_SWAP)
  #define FILL_15BIT_555RGB(r,g,b) {			\
  	*(unsigned short *)fb = SWAP16((unsigned short)(((r>>3)<<10) | ((g>>3)<<5) | (b>>3))); \
  	fb += 2;					\
  }
+#else
+static int tgl;
+static unsigned short p0;
+#define FILL_15BIT_555RGB(r,g,b) {                     \
+	if (!tgl++) {                                    \
+		p0 = SWAP16((unsigned short)(((r>>3)<<10) | ((g>>3)<<5) | (b>>3))); \
+	} else {                                        \
+		tgl=0;                                  \
+		*(unsigned long *)(fb-2) = (SWAP16((unsigned short)(((r>>3)<<10) | ((g>>3)<<5) | (b>>3)))<<16) | p0;    \
+	}                                               \
+	fb += 2;                                        \
+}
+#endif

  #define FILL_16BIT_565RGB(r,g,b) {			\
  	*(unsigned short *)fb = SWAP16((unsigned short)((((r)>>3)<<11) | (((g)>>2)<<5) | ((b)>>3))); \
@@ -1061,8 +1105,20 @@ #endif
  				*dest = ((r >> 5) << 5) | ((g >> 5) << 2) | (b >> 6);
  				break;
  			case GDF_15BIT_555RGB:
+#if !defined(VIDEO_FB_16BPP_PIXEL_SWAP)
  				*(unsigned short *) dest =
  					SWAP16 ((unsigned short) (((r >> 3) << 10) | ((g >> 3) << 5) | (b >> 3)));
+#else
+				{
+					if (!tgl++) {
+						p0 = SWAP16 ((unsigned short) (((r >> 3) << 10) | ((g >> 3) << 5) | (b >> 3)));
+					} else {
+						*(unsigned long *)(dest-2) =
+							 (SWAP16 ((unsigned short) (((r >> 3) << 10) | ((g >> 3) << 5) | (b >> 3)))<<16) | p0;
+						tgl=0;
+					}
+				}
+#endif
  				break;
  			case GDF_16BIT_565RGB:
  				*(unsigned short *) dest =
diff --git a/drivers/mb862xx.c b/drivers/mb862xx.c
new file mode 100644
index 0000000..819064e
--- /dev/null
+++ b/drivers/mb862xx.c
@@ -0,0 +1,423 @@
+/*
+ * (C) Copyright 2007
+ * DENX Software Engineering, Anatolij Gustschin, agust@denx.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mb862xx.c - Graphic interface for Fujitsu CoralP/Lime
+ * PCI and video mode code was derived from smiLynxEM driver.
+ */
+
+#include <common.h>
+
+#if defined(CONFIG_VIDEO_MB862xx)
+
+#include <asm/io.h>
+#include <pci.h>
+#include <video_fb.h>
+#include "videomodes.h"
+#include <mb862xx.h>
+
+/*
+ * Graphic Device
+ */
+GraphicDevice mb862xx;
+
+/*
+ * 32MB external RAM - 256K Chip MMIO = 0x1FC0000 ;
+ */
+#define VIDEO_MEM_SIZE	0x01FC0000
+
+#if defined(CONFIG_PCI)
+#if defined(CONFIG_VIDEO_CORALP)
+
+static struct pci_device_id supported[] = {
+	{ PCI_VENDOR_ID_FUJITSU, PCI_DEVICE_ID_CORAL_P },
+	{ PCI_VENDOR_ID_FUJITSU, PCI_DEVICE_ID_CORAL_PA },
+	{ }
+};
+
+/* Internal clock frequency divider table, index is mode number */
+unsigned int fr_div[] = { 0x00000f00, 0x00000900, 0x00000500 };
+#endif
+#endif
+
+#if defined(CONFIG_VIDEO_CORALP)
+#define	rd_io		in32r
+#define	wr_io		out32r
+#else
+#define	rd_io(addr)	in_be32((volatile unsigned*)(addr))
+#define	wr_io(addr,val)	out_be32((volatile unsigned*)(addr), (val))
+#endif
+
+#define HOST_RD_REG(off)	rd_io((pGD->frameAdrs + 0x01fc0000 + (off)))
+#define HOST_WR_REG(off, val)	wr_io((pGD->frameAdrs + 0x01fc0000 + (off)), (val))
+#define DISP_RD_REG(off)	rd_io((pGD->frameAdrs + 0x01fd0000 + (off)))
+#define DISP_WR_REG(off, val)	wr_io((pGD->frameAdrs + 0x01fd0000 + (off)), (val))
+#define DE_RD_REG(off)		rd_io((pGD->dprBase + (off)))
+#define DE_WR_REG(off, val)	wr_io((pGD->dprBase + (off)), (val))
+
+#if defined(CONFIG_VIDEO_CORALP)
+#define DE_WR_FIFO(val)		wr_io((pGD->dprBase + (0x8400)), (val))
+#else
+#define DE_WR_FIFO(val)		wr_io((pGD->dprBase + (0x04a0)), (val))
+#endif
+
+#define L0PAL_RD_REG(idx, val)	rd_io((pGD->frameAdrs + 0x01fd0400 + ((idx)<<2)))
+#define L0PAL_WR_REG(idx, val)	wr_io((pGD->frameAdrs + 0x01fd0400 + ((idx)<<2)), (val))
+#define L1PAL_RD_REG(idx, val)	rd_io((pGD->frameAdrs + 0x01fd0800 + ((idx)<<2)))
+#define L1PAL_WR_REG(idx, val)	wr_io((pGD->frameAdrs + 0x01fd0800 + ((idx)<<2)), (val))
+#define L2PAL_RD_REG(idx, val)	rd_io((pGD->frameAdrs + 0x01fd1000 + ((idx)<<2)))
+#define L2PAL_WR_REG(idx, val)	wr_io((pGD->frameAdrs + 0x01fd1000 + ((idx)<<2)), (val))
+#define L3PAL_RD_REG(idx, val)	rd_io((pGD->frameAdrs + 0x01fd1400 + ((idx)<<2)))
+#define L3PAL_WR_REG(idx, val)	wr_io((pGD->frameAdrs + 0x01fd1400 + ((idx)<<2)), (val))
+
+static void gdc_sw_reset(void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	HOST_WR_REG (0x002c, 0x00000001);
+	udelay (500);
+	video_hw_init ();
+}
+
+
+static void de_wait(void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	int lc = 0x10000;
+
+	/* Sync with software writes to framebuffer,
+	   try to reset if engine locked */
+	while (DE_RD_REG (0x0400) & 0x00000131)
+		if (lc-- < 0) {
+			gdc_sw_reset ();
+			printf ("gdc reset done after drawing engine lock...\n");
+			break;
+		}
+}
+
+static void de_wait_slots(int slots)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	int lc = 0x10000;
+
+	/* Wait for free fifo slots */
+	while (DE_RD_REG (0x0408) < slots)
+		if (lc-- < 0) {
+			gdc_sw_reset ();
+			printf ("gdc reset done after drawing engine lock...\n");
+			break;
+		}
+}
+
+#if !defined(CONFIG_VIDEO_CORALP)
+static void board_disp_init(void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	const gdc_regs *regs = board_get_regs ();
+
+	while (regs->index) {
+		DISP_WR_REG (regs->index, regs->value);
+		regs++;
+	}
+}
+#endif
+
+/*
+ * Init drawing engine
+ */
+static void de_init (void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	int cf = (pGD->gdfBytesPP == 1) ? 0x0000 : 0x8000;
+
+	pGD->dprBase = pGD->frameAdrs + 0x01ff0000;
+
+	/* Setup mode and fbbase, xres, fg, bg */
+	de_wait_slots (2);
+	DE_WR_FIFO (0xf1010108);
+	DE_WR_FIFO (cf | 0x0300);
+	DE_WR_REG (0x0440, 0x0000);
+	DE_WR_REG (0x0444, pGD->winSizeX);
+	DE_WR_REG (0x0480, 0x0000);
+	DE_WR_REG (0x0484, 0x0000);
+	/* Reset clipping */
+	DE_WR_REG (0x0454, 0x0000);
+	DE_WR_REG (0x0458, pGD->winSizeX);
+	DE_WR_REG (0x045c, 0x0000);
+	DE_WR_REG (0x0460, pGD->winSizeY);
+
+	/* Clear framebuffer using drawing engine */
+	de_wait_slots (3);
+	DE_WR_FIFO (0x09410000);
+	DE_WR_FIFO (0x00000000);
+	DE_WR_FIFO (pGD->winSizeY<<16 | pGD->winSizeX);
+}
+
+#if defined(CONFIG_VIDEO_CORALP)
+unsigned int pci_video_init(void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	pci_dev_t devbusfn;
+
+	if ((devbusfn = pci_find_devices(supported, 0)) < 0)
+	{
+		printf ("PCI video controller not found!\n");
+		return 0;
+	}
+
+	/* PCI setup */
+	pci_write_config_dword (devbusfn, PCI_COMMAND, (PCI_COMMAND_MEMORY | PCI_COMMAND_IO));
+	pci_read_config_dword (devbusfn, PCI_BASE_ADDRESS_0, &pGD->frameAdrs);
+	pGD->frameAdrs = pci_mem_to_phys (devbusfn, pGD->frameAdrs);
+
+	if (pGD->frameAdrs == 0) {
+		printf ("PCI config: failed to get base address\n");
+		return 0;
+	}
+
+	pGD->pciBase = pGD->frameAdrs;
+
+	/* Setup clocks and memory mode for Coral-P Eval. Board */
+	HOST_WR_REG (0x0038, 0x00090000);
+	udelay (200);
+	HOST_WR_REG (0xfffc, 0x11d7fa13);
+	udelay (100);
+	return pGD->frameAdrs;
+}
+
+unsigned int card_init (void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+	unsigned int cf, videomode, div = 0;
+	unsigned long t1, hsync, vsync;
+	char *penv;
+	int tmp, i, bpp;
+	struct ctfb_res_modes *res_mode;
+	struct ctfb_res_modes var_mode;
+
+	memset (pGD, 0, sizeof (GraphicDevice));
+
+	if (!pci_video_init ()) {
+		return 0;
+	}
+
+	printf ("CoralP\n");
+
+	tmp = 0;
+	videomode = 0x310;
+	/* get video mode via environment */
+	if ((penv = getenv ("videomode")) != NULL) {
+		/* deceide if it is a string */
+		if (penv[0] <= '9') {
+			videomode = (int) simple_strtoul (penv, NULL, 16);
+			tmp = 1;
+		}
+	} else {
+		tmp = 1;
+	}
+	if (tmp) {
+		/* parameter are vesa modes */
+		/* search params */
+		for (i = 0; i < VESA_MODES_COUNT; i++) {
+			if (vesa_modes[i].vesanr == videomode)
+				break;
+		}
+		if (i == VESA_MODES_COUNT) {
+			printf ("\tno VESA Mode found, switching to mode 0x%x \n", videomode);
+			i = 0;
+		}
+		res_mode =
+			(struct ctfb_res_modes *) &res_mode_init[vesa_modes[i].resindex];
+		if (vesa_modes[i].resindex > 2) {
+			printf ("\tUnsupported resolution, switching to default\n");
+			bpp = vesa_modes[1].bits_per_pixel;
+			div = fr_div[1];
+		}
+		bpp = vesa_modes[i].bits_per_pixel;
+		div = fr_div[vesa_modes[i].resindex];
+	} else {
+
+		res_mode = (struct ctfb_res_modes *) &var_mode;
+		bpp = video_get_params (res_mode, penv);
+	}
+
+	/* calculate hsync and vsync freq (info only) */
+	t1 = (res_mode->left_margin + res_mode->xres +
+	      res_mode->right_margin + res_mode->hsync_len) / 8;
+	t1 *= 8;
+	t1 *= res_mode->pixclock;
+	t1 /= 1000;
+	hsync = 1000000000L / t1;
+	t1 *= (res_mode->upper_margin + res_mode->yres +
+	       res_mode->lower_margin + res_mode->vsync_len);
+	t1 /= 1000;
+	vsync = 1000000000L / t1;
+
+	/* fill in Graphic device struct */
+	sprintf (pGD->modeIdent, "%dx%dx%d %ldkHz %ldHz", res_mode->xres,
+		 res_mode->yres, bpp, (hsync / 1000), (vsync / 1000));
+	printf ("\t%s\n", pGD->modeIdent);
+	pGD->winSizeX = res_mode->xres;
+	pGD->winSizeY = res_mode->yres;
+	pGD->memSize = VIDEO_MEM_SIZE;
+
+	switch (bpp) {
+	case 8:
+		pGD->gdfIndex = GDF__8BIT_INDEX;
+		pGD->gdfBytesPP = 1;
+		break;
+	case 15:
+	case 16:
+		pGD->gdfIndex = GDF_15BIT_555RGB;
+		pGD->gdfBytesPP = 2;
+		break;
+	#if 0
+		/* TODO: Could be done but we have to implement rectfill
+			 and bitblt SW fallbacks for this */
+	case 24:
+	case 32:
+		pGD->gdfIndex = GDF_24BIT_888RGB;
+		pGD->gdfBytesPP = 4;
+		break;
+	#endif
+	default:
+		printf ("\t%d bpp configured, but only 8,15 and 16 supported.\n", bpp);
+		printf ("\tSwitching back to 15bpp\n");
+		pGD->gdfIndex = GDF_15BIT_555RGB;
+		pGD->gdfBytesPP = 2;
+	}
+
+	/* Setup dot clock (internal pll, division rate) */
+	DISP_WR_REG (0x0100, div);
+	/* L0 init */
+	cf = (pGD->gdfBytesPP == 1) ? 0x00000000 : 0x80000000;
+	DISP_WR_REG (0x0020, ((pGD->winSizeX * pGD->gdfBytesPP)/64)<<16 |
+			     (pGD->winSizeY-1) |
+			     cf);
+	DISP_WR_REG (0x0024, 0x00000000);
+	DISP_WR_REG (0x0028, 0x00000000);
+	DISP_WR_REG (0x002c, 0x00000000);
+	DISP_WR_REG (0x0110, 0x00000000);
+	DISP_WR_REG (0x0114, 0x00000000);
+	DISP_WR_REG (0x0118, (pGD->winSizeY-1)<<16 | pGD->winSizeX);
+
+	/* Display timing init */
+	DISP_WR_REG (0x0004, (pGD->winSizeX+res_mode->left_margin+res_mode->right_margin+res_mode->hsync_len-1)<<16);
+	DISP_WR_REG (0x0008, (pGD->winSizeX-1) << 16 | (pGD->winSizeX-1));
+	DISP_WR_REG (0x000c, (res_mode->vsync_len-1)<<24|(res_mode->hsync_len-1)<<16|(pGD->winSizeX+res_mode->right_margin-1));
+	DISP_WR_REG (0x0010, (pGD->winSizeY+res_mode->lower_margin+res_mode->upper_margin+res_mode->vsync_len-1)<<16);
+	DISP_WR_REG (0x0014, (pGD->winSizeY-1) << 16 | (pGD->winSizeY+res_mode->lower_margin-1));
+	DISP_WR_REG (0x0018, 0x00000000);
+	DISP_WR_REG (0x001c, pGD->winSizeY << 16 | pGD->winSizeX);
+	/* Display enable, L0 layer */
+	DISP_WR_REG (0x0100, 0x80010000 | div);
+
+	return pGD->frameAdrs;
+}
+#endif
+
+void *video_hw_init (void)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+
+	printf ("Video: Fujitsu ");
+
+	memset (pGD, 0, sizeof (GraphicDevice));
+
+#if defined(CONFIG_VIDEO_CORALP)
+	if (card_init () == 0) {
+		return (NULL);
+	}
+#else
+	/* Preliminary init of the onboard graphic controller,
+	   retrieve base address */
+	if ((pGD->frameAdrs = board_video_init ()) == 0) {
+		printf ("Controller not found!\n");
+		return (NULL);
+	} else
+		printf("Lime\n");
+#endif
+
+	de_init ();
+
+#if !defined(CONFIG_VIDEO_CORALP)
+	board_disp_init();
+#endif
+
+#if defined(CONFIG_LWMON5)
+	/* Lamp on */
+	board_backlight_switch (1);
+#endif
+
+	return pGD;
+}
+
+/*
+ * Set a RGB color in the LUT
+ */
+void video_set_lut (unsigned int index, unsigned char r, unsigned char g, unsigned char b)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+
+	L0PAL_WR_REG (index, (r << 16) | (g << 8) | (b));
+}
+
+/*
+ * Drawing engine Fill and BitBlt screen region
+ */
+void video_hw_rectfill (unsigned int bpp, unsigned int dst_x, unsigned int dst_y,
+			unsigned int dim_x, unsigned int dim_y, unsigned int color)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+
+	de_wait_slots (3);
+	DE_WR_REG (0x0480, color);
+	DE_WR_FIFO (0x09410000);
+	DE_WR_FIFO ((dst_y << 16) | dst_x);
+	DE_WR_FIFO ((dim_y << 16) | dim_x);
+	de_wait ();
+}
+
+void video_hw_bitblt (unsigned int bpp, unsigned int src_x, unsigned int src_y,
+		      unsigned int dst_x, unsigned int dst_y, unsigned int width,
+		      unsigned int height)
+{
+	GraphicDevice *pGD = (GraphicDevice *)&mb862xx;
+        unsigned int ctrl = 0x0d000000L;
+
+	if (src_x >= dst_x && src_y >= dst_y)
+                ctrl |= 0x00440000L;
+        else if (src_x >= dst_x && src_y <= dst_y)
+                ctrl |= 0x00460000L;
+        else if (src_x <= dst_x && src_y >= dst_y)
+                ctrl |= 0x00450000L;
+        else
+                ctrl |= 0x00470000L;
+
+	de_wait_slots (4);
+	DE_WR_FIFO (ctrl);
+	DE_WR_FIFO ((src_y << 16) | src_x);
+	DE_WR_FIFO ((dst_y << 16) | dst_x);
+	DE_WR_FIFO ((height << 16) | width);
+	de_wait (); /* sync */
+}
+#endif /* CONFIG_VIDEO_MB862xx */
diff --git a/include/mb862xx.h b/include/mb862xx.h
new file mode 100644
index 0000000..1af5670
--- /dev/null
+++ b/include/mb862xx.h
@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2007
+ * DENX Software Engineering, Anatolij Gustschin, agust at denx.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mb862xx.h - Graphic interface for Fujitsu CoralP/Lime
+ */
+
+#ifndef _MB862XX_H_
+#define _MB862XX_H_
+
+#define PCI_VENDOR_ID_FUJITSU	0x10CF
+#define PCI_DEVICE_ID_CORAL_P	0x2019
+#define PCI_DEVICE_ID_CORAL_PA	0x201E
+
+typedef struct {
+	unsigned int index;
+	unsigned int value;
+} gdc_regs;
+
+const gdc_regs *board_get_regs (void);
+unsigned int board_video_init (void);
+void board_backlight_switch(int);
+
+#endif /* _MB862XX_H_ */
-- 
1.4.1
--
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office@denx.de

^ permalink raw reply related	[flat|nested] 5+ messages in thread
end of thread, other threads:[~2008-01-10 14:03 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-09-24 19:00 [U-Boot-Users] [PATCH] Add Fujitsu CoralP/Lime video driver Anatolij Gustschin
2008-01-09  8:05 ` Wolfgang Denk
2008-01-09  9:08   ` Stefan Roese
2008-01-09  9:53     ` Rodolfo Giometti
2008-01-10 14:03       ` Rodolfo Giometti

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox