* [U-Boot-Users] [PATCH]ppc_4xx: Netstal HCU5 board. Added POST. Various fixes
@ 2008-01-14 13:36 Niklaus Giger
2008-01-14 14:58 ` Stefan Roese
0 siblings, 1 reply; 2+ messages in thread
From: Niklaus Giger @ 2008-01-14 13:36 UTC (permalink / raw)
To: u-boot
Various fixes. Reduced rom_size from 384 to 320 kB.
Environment is now in flash.
Added POST, support for OF.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
---
board/netstal/hcu5/config.mk | 2 +-
include/configs/hcu5.h | 61 +++++++++++++++++++++++++++++------------
2 files changed, 44 insertions(+), 19 deletions(-)
diff --git a/board/netstal/hcu5/config.mk b/board/netstal/hcu5/config.mk
index cfd5744..05b879f 100644
--- a/board/netstal/hcu5/config.mk
+++ b/board/netstal/hcu5/config.mk
@@ -21,7 +21,7 @@
# Netstal Maschinen AG: HCU5 boards
#
-TEXT_BASE = 0xFFFa0000
+TEXT_BASE = 0xFFFb0000
PLATFORM_CPPFLAGS += -DCONFIG_440=1
diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h
index 1440838..05185d2 100644
--- a/include/configs/hcu5.h
+++ b/include/configs/hcu5.h
@@ -48,9 +48,10 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
+#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+#define CFG_TLB_FOR_BOOT_FLASH 3
#define CFG_BOOT_BASE_ADDR 0xfff00000
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */
@@ -97,6 +98,7 @@
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#undef CONFIG_UART1_CONSOLE
+#undef CONFIG_CMD_HWFLOW
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -105,8 +107,8 @@
*----------------------------------------------------------------------*/
#undef CFG_ENV_IS_IN_NVRAM
-#undef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_IS_IN_FLASH
+#undef CFG_ENV_IS_IN_EEPROM
#undef CFG_ENV_IS_NOWHERE
#ifdef CFG_ENV_IS_IN_EEPROM
@@ -121,21 +123,30 @@
/* Put the environment in Flash */
#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CFG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+/*
+#undef CFG_ENV_ADDR_REDUND
+#undef CFG_ENV_SIZE_REDUND
+*/
#endif
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CFG_MBYTES_SDRAM (128) /* 128 MB or 256 MB */
-#define CFG_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
+#define CFG_DDR_CACHED_ADDR 0x50000000 /* setup 2nd TLB cached here */
#undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */
#define CONFIG_DDR_ECC 1 /* enable ECC */
+/* Following two definitions must be kept in sync with config.h of vxWorks */
+#define USER_RESERVED_MEM ( 0) /* in kB */
+#define PM_RESERVED_MEM ( 64) /* in kB: pmLib reserved area size */
+#define CONFIG_PRAM ( USER_RESERVED_MEM + PM_RESERVED_MEM )
+
/*-----------------------------------------------------------------------
* I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
* the second internal I2C controller of the PPC440EPx
@@ -167,7 +178,7 @@
/* Setup some board specific values for the default environment variables */
#define CONFIG_HOSTNAME hcu5
-#define CONFIG_IPADDR 172.25.1.42
+#define CONFIG_IPADDR 172.25.1.99
#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
#define CONFIG_OVERWRITE_ETHADDR_ONCE
#define CONFIG_SERVERIP 172.25.1.3
@@ -189,13 +200,23 @@
"bootfile=hcu5/uImage\0" \
"rootpath=/home/hcu/eldk/ppc_4xxFP\0" \
"load=tftp 100000 hcu5/u-boot.bin\0" \
- "update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;" \
- "cp.b 100000 FFFa0000 60000\0" \
+ "update=protect off FFFb0000 FFFFFFFF;era FFFb0000 FFFFFFFF;" \
+ "cp.b 100000 FFFb0000 50000\0" \
"upd=run load;run update\0" \
- "vx=tftp ${loadaddr} hcu5/hcu5_vx_rom;" \
- "setenv bootargs emac(0,0)hcu5_vx_rom e=${ipaddr} " \
- " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008;" \
- "bootvx ${loadaddr}\0" \
+ "vx=tftp ${loadaddr} hcu5/hcu5_vx_rom; run vxboot\0" \
+ "vxusb=usb start; fatload usb 0 ${loadaddr} vxWorks.st; run vxboot\0" \
+ "vxargs=emac(0,0)c:hcu5/hcu5_vx_rom e=${ipaddr} h=${serverip}" \
+ " u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \
+ "vxboot=setenv bootargs $(vxargs); bootvx ${loadaddr}\0" \
+ "usbargs=setenv bootargs root=/dev/sda1 ro\0" \
+ "linux=usb start; ext2load usb 0 ${loadaddr} /boot/uImage;" \
+ "run usbargs addip addtty; bootm\0" \
+ "net_nfs_fdt=tftp 200000 ${bootfile};" \
+ "tftp ${fdt_addr} ${fdt_file};" \
+ "run nfsargs addip addtty;" \
+ "bootm 200000 - ${fdt_addr}\0" \
+ "fdt_file=hcu5/hcu5.dtb\0" \
+ "fdt_addr=400000\0" \
""
#define CONFIG_BOOTCOMMAND "run vx"
@@ -248,7 +269,6 @@
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BSP
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
@@ -268,7 +288,6 @@
/* POST support */
#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_ECC | \
CFG_POST_CPU | \
CFG_POST_UART | \
CFG_POST_I2C | \
@@ -276,6 +295,8 @@
CFG_POST_FPU | \
CFG_POST_ETHER | \
CFG_POST_SPR)
+/* CFG_POST_ECC | \ */
+#define CFG_POST_UART_TABLE {UART0_BASE}
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CONFIG_LOGBUFFER
@@ -309,16 +330,15 @@
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
-#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI 1 /* include pci support */
#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
/* Board-specific PCI */
@@ -342,7 +362,7 @@
#define CFG_CS_1 0xC8000000 /* CAN */
#define CFG_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */
#define CFG_CPLD CFG_CS_2
-#define CFG_CS_3 0xCD000000 /* CPLD and IMC-Bus Fast */
+#define CFG_CS_3 0xCE000000 /* CPLD and IMC-Bus Fast */
/*-----------------------------------------------------------------------
* FLASH organization
@@ -399,4 +419,9 @@
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
#endif /* __CONFIG_H */
--
1.5.2.5
--
Niklaus Giger
Netstal Maschinen AG
CH-8752 Naefels
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [U-Boot-Users] [PATCH]ppc_4xx: Netstal HCU5 board. Added POST. Various fixes
2008-01-14 13:36 [U-Boot-Users] [PATCH]ppc_4xx: Netstal HCU5 board. Added POST. Various fixes Niklaus Giger
@ 2008-01-14 14:58 ` Stefan Roese
0 siblings, 0 replies; 2+ messages in thread
From: Stefan Roese @ 2008-01-14 14:58 UTC (permalink / raw)
To: u-boot
On Monday 14 January 2008, Niklaus Giger wrote:
> Various fixes. Reduced rom_size from 384 to 320 kB.
> Environment is now in flash.
> Added POST, support for OF.
I suggest to change this commit text into something like this:
- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF
Better overview, don't you think?
More comments below.
> Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
> ---
> board/netstal/hcu5/config.mk | 2 +-
> include/configs/hcu5.h | 61
> +++++++++++++++++++++++++++++------------ 2 files changed, 44
> insertions(+), 19 deletions(-)
>
> diff --git a/board/netstal/hcu5/config.mk b/board/netstal/hcu5/config.mk
> index cfd5744..05b879f 100644
> --- a/board/netstal/hcu5/config.mk
> +++ b/board/netstal/hcu5/config.mk
> @@ -21,7 +21,7 @@
> # Netstal Maschinen AG: HCU5 boards
> #
>
> -TEXT_BASE = 0xFFFa0000
> +TEXT_BASE = 0xFFFb0000
Again, upper case or lower case please.
> PLATFORM_CPPFLAGS += -DCONFIG_440=1
>
> diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h
> index 1440838..05185d2 100644
> --- a/include/configs/hcu5.h
> +++ b/include/configs/hcu5.h
> @@ -48,9 +48,10 @@
> * Base addresses -- Note these are effective addresses where the
> * actual resources get mapped (not physical addresses)
> *----------------------------------------------------------------------*/
> -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
> +#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
> #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
>
> +#define CFG_TLB_FOR_BOOT_FLASH 3
> #define CFG_BOOT_BASE_ADDR 0xfff00000
> #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
> #define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */
> @@ -97,6 +98,7 @@
> #undef CONFIG_SERIAL_SOFTWARE_FIFO
> #undef CONFIG_UART1_CONSOLE
>
> +#undef CONFIG_CMD_HWFLOW
> #define CFG_BAUDRATE_TABLE \
> {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
>
> @@ -105,8 +107,8 @@
> *----------------------------------------------------------------------*/
>
> #undef CFG_ENV_IS_IN_NVRAM
> -#undef CFG_ENV_IS_IN_FLASH
> -#define CFG_ENV_IS_IN_EEPROM
> +#define CFG_ENV_IS_IN_FLASH
> +#undef CFG_ENV_IS_IN_EEPROM
> #undef CFG_ENV_IS_NOWHERE
>
> #ifdef CFG_ENV_IS_IN_EEPROM
> @@ -121,21 +123,30 @@
> /* Put the environment in Flash */
> #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
> #define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
> -#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
> +#define CFG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
>
> /* Address and size of Redundant Environment Sector */
> #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
> #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
> +/*
> +#undef CFG_ENV_ADDR_REDUND
> +#undef CFG_ENV_SIZE_REDUND
> +*/
Please remove it when it's not used/defined.
> #endif
>
> /*-----------------------------------------------------------------------
> * DDR SDRAM
> *----------------------------------------------------------------------*/
> #define CFG_MBYTES_SDRAM (128) /* 128 MB or 256 MB */
> -#define CFG_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
> +#define CFG_DDR_CACHED_ADDR 0x50000000 /* setup 2nd TLB cached here */
> #undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */
> #define CONFIG_DDR_ECC 1 /* enable ECC */
>
> +/* Following two definitions must be kept in sync with config.h of vxWorks
> */ +#define USER_RESERVED_MEM ( 0) /* in kB */
> +#define PM_RESERVED_MEM ( 64) /* in kB: pmLib reserved area size
> */ +#define CONFIG_PRAM ( USER_RESERVED_MEM + PM_RESERVED_MEM ) +
> /*-----------------------------------------------------------------------
> * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
> * the second internal I2C controller of the PPC440EPx
> @@ -167,7 +178,7 @@
>
> /* Setup some board specific values for the default environment variables
> */ #define CONFIG_HOSTNAME hcu5
> -#define CONFIG_IPADDR 172.25.1.42
> +#define CONFIG_IPADDR 172.25.1.99
> #define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG
> MAC */ #define CONFIG_OVERWRITE_ETHADDR_ONCE
> #define CONFIG_SERVERIP 172.25.1.3
> @@ -189,13 +200,23 @@
> "bootfile=hcu5/uImage\0" \
> "rootpath=/home/hcu/eldk/ppc_4xxFP\0" \
> "load=tftp 100000 hcu5/u-boot.bin\0" \
> - "update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;" \
> - "cp.b 100000 FFFa0000 60000\0" \
> + "update=protect off FFFb0000 FFFFFFFF;era FFFb0000 FFFFFFFF;" \
> + "cp.b 100000 FFFb0000 50000\0" \
> "upd=run load;run update\0" \
> - "vx=tftp ${loadaddr} hcu5/hcu5_vx_rom;" \
> - "setenv bootargs emac(0,0)hcu5_vx_rom e=${ipaddr} " \
> - " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008;" \
> - "bootvx ${loadaddr}\0" \
> + "vx=tftp ${loadaddr} hcu5/hcu5_vx_rom; run vxboot\0" \
> + "vxusb=usb start; fatload usb 0 ${loadaddr} vxWorks.st; run vxboot\0" \
> + "vxargs=emac(0,0)c:hcu5/hcu5_vx_rom e=${ipaddr} h=${serverip}" \
> + " u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \
> + "vxboot=setenv bootargs $(vxargs); bootvx ${loadaddr}\0" \
> + "usbargs=setenv bootargs root=/dev/sda1 ro\0" \
> + "linux=usb start; ext2load usb 0 ${loadaddr} /boot/uImage;" \
> + "run usbargs addip addtty; bootm\0" \
> + "net_nfs_fdt=tftp 200000 ${bootfile};" \
> + "tftp ${fdt_addr} ${fdt_file};" \
> + "run nfsargs addip addtty;" \
> + "bootm 200000 - ${fdt_addr}\0" \
> + "fdt_file=hcu5/hcu5.dtb\0" \
> + "fdt_addr=400000\0" \
> ""
> #define CONFIG_BOOTCOMMAND "run vx"
>
> @@ -248,7 +269,6 @@
> #include <config_cmd_default.h>
>
> #define CONFIG_CMD_ASKENV
> -#define CONFIG_CMD_BSP
> #define CONFIG_CMD_DHCP
> #define CONFIG_CMD_DIAG
> #define CONFIG_CMD_EEPROM
> @@ -268,7 +288,6 @@
>
> /* POST support */
> #define CONFIG_POST (CFG_POST_MEMORY | \
> - CFG_POST_ECC | \
> CFG_POST_CPU | \
> CFG_POST_UART | \
> CFG_POST_I2C | \
> @@ -276,6 +295,8 @@
> CFG_POST_FPU | \
> CFG_POST_ETHER | \
> CFG_POST_SPR)
> +/* CFG_POST_ECC | \ */
Remove unsed code.
> +#define CFG_POST_UART_TABLE {UART0_BASE}
>
> #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
> #define CONFIG_LOGBUFFER
> @@ -309,16 +330,15 @@
> #define CONFIG_CMDLINE_EDITING 1 /* add command line history */
> #define CONFIG_LOOPW 1 /* enable loopw command */
> #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
> -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0
> */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
>
> /*-----------------------------------------------------------------------
> * PCI stuff
> *----------------------------------------------------------------------*/
> /* General PCI */
> -#define CONFIG_PCI /* include pci support */
> +#define CONFIG_PCI 1 /* include pci support */
> #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
> -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
> +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
> #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to
> CFG_PCI_MEMBASE*/
>
> /* Board-specific PCI */
> @@ -342,7 +362,7 @@
> #define CFG_CS_1 0xC8000000 /* CAN */
> #define CFG_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */
> #define CFG_CPLD CFG_CS_2
> -#define CFG_CS_3 0xCD000000 /* CPLD and IMC-Bus Fast */
> +#define CFG_CS_3 0xCE000000 /* CPLD and IMC-Bus Fast */
>
> /*-----------------------------------------------------------------------
> * FLASH organization
> @@ -399,4 +419,9 @@
> #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
> #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
> #endif
> +
> +/* pass open firmware flat tree */
> +#define CONFIG_OF_LIBFDT 1
> +#define CONFIG_OF_BOARD_SETUP 1
> +
> #endif /* __CONFIG_H */
> --
> 1.5.2.5
--
Viele Gr??e,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2008-01-14 14:58 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-01-14 13:36 [U-Boot-Users] [PATCH]ppc_4xx: Netstal HCU5 board. Added POST. Various fixes Niklaus Giger
2008-01-14 14:58 ` Stefan Roese
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox