[U-Boot-Users] [PATCH] 4xx: Minor updates for DU440 boards

[U-Boot-Users] [PATCH] 4xx: Minor updates for DU440 boards

[Matthias Fuchs]

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
---
 board/esd/du440/du440.c |    5 +++--
 board/esd/du440/du440.h |    1 +
 include/configs/DU440.h |   16 ++++++----------
 3 files changed, 10 insertions(+), 12 deletions(-)

diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index ceb128c..3dbb2e1 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -67,12 +67,12 @@ int board_early_init_f(void)
 	out_be32((void*)GPIO1_OR, 0x00000000);
 	out_be32((void*)GPIO1_TCR, 0xc2000000 |
 		 CFG_GPIO1_IORSTN |
+		 CFG_GPIO1_IORST2N |
 		 CFG_GPIO1_LEDUSR1 |
 		 CFG_GPIO1_LEDUSR2 |
 		 CFG_GPIO1_LEDPOST |
 		 CFG_GPIO1_LEDDU);
 	out_be32((void*)GPIO1_ODR, CFG_GPIO1_LEDDU);
-
 	out_be32((void*)GPIO1_OSRL, 0x5c280000);
 	out_be32((void*)GPIO1_OSRH, 0x00000000);
 	out_be32((void*)GPIO1_TSRL, 0x0c000000);
@@ -243,7 +243,8 @@ int misc_init_r(void)
 	 * release IO-RST#
 	 * We have to wait at least 560ms until we may call usbhub_init
 	 */
-	out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) | CFG_GPIO1_IORSTN);
+	out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) |
+		 CFG_GPIO1_IORSTN | CFG_GPIO1_IORST2N);
 
 	/*
 	 * flash USR1/2 LEDs (600ms)
diff --git a/board/esd/du440/du440.h b/board/esd/du440/du440.h
index 5c362e4..83fdac7 100644
--- a/board/esd/du440/du440.h
+++ b/board/esd/du440/du440.h
@@ -24,6 +24,7 @@
 #define CFG_GPIO1_DCF77		(0x80000000 >> (42-32))  /* GPIO1_42 */
 
 #define CFG_GPIO1_IORSTN	(0x80000000 >> (55-32))  /* GPIO1_55 */
+#define CFG_GPIO1_IORST2N	(0x80000000 >> (47-32))  /* GPIO1_47 */
 
 #define CFG_GPIO1_HWVER_MASK	0x000000f0 /* GPIO1_56-59 */
 #define CFG_GPIO1_HWVER_SHIFT	4
diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index 4fb6921..f193a43 100644
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -157,10 +157,9 @@
  */
 #define CFG_MBYTES_SDRAM        (1024)	/* 512 MiB      TODO: remove    */
 #define CONFIG_DDR_DATA_EYE		/* use DDR2 optimization        */
+#define CFG_MEM_TOP_HIDE        (4 << 10) /* don't use last 4kbytes     */
+                                        /* 440EPx errata CHIP 11        */
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for setup     */
-#if 0
-#define CONFIG_ZERO_SDRAM		/* Zero SDRAM after setup       */
-#endif
 #define CONFIG_DDR_ECC			/* Use ECC when available       */
 #define SPD_EEPROM_ADDRESS	{0x50}
 #define CONFIG_PROG_SDRAM_TLB
@@ -244,9 +243,6 @@
 	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
 		"cp.b 100000 FFFA0000 60000\0"				\
 	""
-#if 0
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-#endif
 
 #define CONFIG_PREBOOT                  /* enable preboot variable      */
 
@@ -264,7 +260,7 @@ int du440_phy_addr(int devnum);
 #define CONFIG_PHY_ADDR		du440_phy_addr(0) /* PHY address	*/
 
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
-#define CONFIG_PHY_GIGE		1	/* Include GbE detection	*/
+#undef CONFIG_PHY_GIGE			/* no GbE detection		*/
 
 #define CONFIG_HAS_ETH0
 #define CFG_RX_ETH_BUFFER	128
@@ -295,7 +291,9 @@ int du440_phy_addr(int devnum);
 
 #include <config_cmd_default.h>
 
+#define CONFIG_CMD_AUTOSCRIPT
 #define CONFIG_CMD_BSP
+#define CONFIG_CMD_BMP
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
@@ -431,8 +429,6 @@ int du440_phy_addr(int devnum);
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
-#if 0
-#define CONFIG_SHOW_ACTIVITY      1
-#endif
+#define CONFIG_AUTOSCRIPT	1
 
 #endif	/* __CONFIG_H */
-- 
1.5.3

[U-Boot-Users] [PATCH] 4xx: Minor updates for DU440 boards

[Stefan Roese]

On Sunday 30 March 2008, Matthias Fuchs wrote:
> Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

Applied to u-boot-ppc4xx. Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================