[U-Boot-Users] Problem with the prompt

[U-Boot-Users] Problem with the prompt

[navin karnam]

Hi all,


When u-boot is loaded on board following messages come on my board.



U-Boot 1.3.3 (Jul  2 2008 - 10:34:34)



DRAM:  256 MB

ERROR: too many flash sectors

Flash: 64 MB

*** Warning - bad CRC, using default environment



In:    serial

Out:   serial

Err:   serial

$





If I don't press any key, within 1 minute above things repeat on hyper
terminal again. Actually till user doesn't press anything, above messages
should not repeat on hyper terminal.

Kindly note that

1)      CONFIG_BOOTDELAY  -1

And none of the below #defines are enabled



CONFIG_BOOT_RETRY_TIME

            CONFIG_BOOT_RETRY_MIN

            CONFIG_AUTOBOOT_KEYED

            CONFIG_AUTOBOOT_PROMPT

            CONFIG_AUTOBOOT_DELAY_STR

            CONFIG_AUTOBOOT_STOP_STR

            CONFIG_AUTOBOOT_DELAY_STR2

            CONFIG_AUTOBOOT_STOP_STR2

            CONFIG_ZERO_BOOTDELAY_CHECK

      CONFIG_RESET_TO_RETRY




-- 
Regards,
Naveen
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080702/c6c3a34d/attachment.htm 

[U-Boot-Users] Problem with the prompt

[Karthikeyan]

Problem might be in SDRAM configuration. Just check it...

 

Regards,

Karthikeyan

 

 

 

________________________________

From: u-boot-users-bounces@lists.sourceforge.net
[mailto:u-boot-users-bounces at lists.sourceforge.net] On Behalf Of navin
karnam
Sent: Wednesday, July 02, 2008 11:36 AM
To: u-boot-users at lists.sourceforge.net
Subject: [U-Boot-Users] Problem with the prompt

 

Hi all,

 

When u-boot is loaded on board following messages come on my board.

 

U-Boot 1.3.3 (Jul  2 2008 - 10:34:34)

 

DRAM:  256 MB

ERROR: too many flash sectors

Flash: 64 MB

*** Warning - bad CRC, using default environment

 

In:    serial

Out:   serial

Err:   serial

$

 

 

If I don't press any key, within 1 minute above things repeat on hyper
terminal again. Actually till user doesn't press anything, above
messages should not repeat on hyper terminal.

Kindly note that 

1)      CONFIG_BOOTDELAY  -1

And none of the below #defines are enabled

 

CONFIG_BOOT_RETRY_TIME

            CONFIG_BOOT_RETRY_MIN

            CONFIG_AUTOBOOT_KEYED

            CONFIG_AUTOBOOT_PROMPT

            CONFIG_AUTOBOOT_DELAY_STR

            CONFIG_AUTOBOOT_STOP_STR

            CONFIG_AUTOBOOT_DELAY_STR2

            CONFIG_AUTOBOOT_STOP_STR2

            CONFIG_ZERO_BOOTDELAY_CHECK

      CONFIG_RESET_TO_RETRY

 



-- 
Regards,
Naveen



DISCLAIMER:
-----------------------------------------------------------------------------------------------------------------------

The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only.
It shall not attach any liability on the originator or HCL or its affiliates. Any views or opinions presented in 
this email are solely those of the author and may not necessarily reflect the opinions of HCL or its affiliates.
Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of 
this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have
received this email in error please delete it and notify the sender immediately. Before opening any mail and 
attachments please check them for viruses and defect.

-----------------------------------------------------------------------------------------------------------------------
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080702/3635716f/attachment.htm 

[U-Boot-Users] Problem with the prompt

[Stefan Roese]

On Wednesday 02 July 2008, navin karnam wrote:
> When u-boot is loaded on board following messages come on my board.
>
> U-Boot 1.3.3 (Jul  2 2008 - 10:34:34)
>
> DRAM:  256 MB
> ERROR: too many flash sectors

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

> Flash: 64 MB
> *** Warning - bad CRC, using default environment
>
>
> In:    serial
> Out:   serial
> Err:   serial
>
> $

I suggest that you first solve the problem above with the "too many flash 
sectors". Most like you only need to increase CFG_MAX_FLASH_SECT in your 
board config file.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================