public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
* [U-Boot] Problems with USB mass storage on at91sam9263
@ 2009-01-14 11:06 Paal Bakken
  2009-01-14 18:53 ` Remy Bohmer
  0 siblings, 1 reply; 8+ messages in thread
From: Paal Bakken @ 2009-01-14 11:06 UTC (permalink / raw)
  To: u-boot

I have problems with usb mass storage in u-boot.

We have our own at91sam9263 board, but I experience exactly the same problems on the standard at91sam9263ek. And the usb-port AND memory stick works fine in linux. I have tried both FAT and FAT32. Below follows an edited screendump of some usb commands with a u-boot snapshot version from 13.01.2009.

I have seen that there has been done a lot of work on the usb code in the last months, but it seems to have calmed down. Is the 2009-01-rc1 and/or the current snapshot supposed to work? Is there anything I can do to avoid this problem?


Best regards,

P?l Bakken



And the edited screen-dump:

-----------------------------------------


U-Boot 2009.01-rc1 (jan. 13 2009 - 14:42:22)


DRAM:  64 MB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  1


DUnf-Boot2009> usb start

(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... ERROR:  USB-error: STALL: TD was moved to the Done Queue because the endpoint returned a STALL PID (4)
ERROR: USB-error: STALL: TD was moved to the Done Queue because the endpoint returned a STALL PID (4)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
:
        225 more of the same error? :-)
:
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5) Device NOT ready
   Request Sense returned 00 00 00
1 Storage Device(s) found

DUnf-Boot2009> usb tree

Device Tree:
  1  Hub (12MBit/s, 0mA)
  |   OHCI Root Hub
  |
  |?-2  Mass Storage (12MBit/s, 100mA)
       TTI-MSA      USB 2.0 Mobile Disk     FF04091900068

DUnf-Boot2009> usb info

1: Hub,  USB Revision 1.10
 -  OHCI Root Hub
 - Class: Hub
 - PacketSize: 8  Configurations: 1
 - Vendor: 0x0000  Product 0x0000 Version 0.0
   Configuration: 1
   - Interfaces: 1 Self Powered 0mA
     Interface: 0
     - Alternate Setting 0, Endpoints: 1
     - Class Hub
     - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms

2: Mass Storage,  USB Revision 2.0
 - TTI-MSA      USB 2.0 Mobile Disk     FF04091900068
 - Class: (from Interface) Mass Storage
 - PacketSize: 64  Configurations: 1
 - Vendor: 0x126f  Product 0x1325 Version 1.0
   Configuration: 1
   - Interfaces: 1 Bus Powered 100mA
   - ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)

     Interface: 0
     - Alternate Setting 0, Endpoints: 3
     - Class Mass Storage, Transp. SCSI, Bulk only
     - ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)

     - Endpoint 1 In Bulk MaxPacket 64
     - Endpoint 2 Out Bulk MaxPacket 64
     - Endpoint 3 In Interrupt MaxPacket 2 Interval 1ms

DUnf-Boot2009> usb storage
  Device 0: Vendor:  Rev:  Prod:
            Type: Removable Hard Disk
            Capacity: not available

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-14 11:06 [U-Boot] Problems with USB mass storage on at91sam9263 Paal Bakken
@ 2009-01-14 18:53 ` Remy Bohmer
  2009-01-14 21:30   ` Paal Bakken
  2009-01-16 16:30   ` Stelian Pop
  0 siblings, 2 replies; 8+ messages in thread
From: Remy Bohmer @ 2009-01-14 18:53 UTC (permalink / raw)
  To: u-boot

Hello,

2009/1/14 Paal Bakken <pabakken@online.no>:
> I have problems with usb mass storage in u-boot.
> We have our own at91sam9263 board, but I experience exactly the same problems on the standard at91sam9263ek. And the usb-port AND memory stick works fine in linux. I have tried both FAT and FAT32. Below follows an edited screendump of some usb commands with a u-boot snapshot version from 13.01.2009.

The current version should work, indeed a lot has been done in that
area for these cores. However, IIRC there were some problems with the
bootstrap code not initialising the PLLB correctly, which resulted in
similar errors. I thought that Stelian got it to work finally on this
particular core as well, so maybe he can confirm this. (I concentrated
the patches on the sam9261)

Kind Regards,

Remy

> (Re)start USB...
> USB:   scanning bus for devices... 2 USB Device(s) found
>       scanning bus for storage devices... ERROR:  USB-error: STALL: TD was moved to the Done Queue because the endpoint returned a STALL PID (4)
> ERROR: USB-error: STALL: TD was moved to the Done Queue because the endpoint returned a STALL PID (4)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> :
>        225 more of the same error? :-)
> :
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5) Device NOT ready
>   Request Sense returned 00 00 00
> 1 Storage Device(s) found
>
> DUnf-Boot2009> usb tree
>
> Device Tree:
>  1  Hub (12MBit/s, 0mA)
>  |   OHCI Root Hub
>  |
>  |?-2  Mass Storage (12MBit/s, 100mA)
>       TTI-MSA      USB 2.0 Mobile Disk     FF04091900068
>
> DUnf-Boot2009> usb info
>
> 1: Hub,  USB Revision 1.10
>  -  OHCI Root Hub
>  - Class: Hub
>  - PacketSize: 8  Configurations: 1
>  - Vendor: 0x0000  Product 0x0000 Version 0.0
>   Configuration: 1
>   - Interfaces: 1 Self Powered 0mA
>     Interface: 0
>     - Alternate Setting 0, Endpoints: 1
>     - Class Hub
>     - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms
>
> 2: Mass Storage,  USB Revision 2.0
>  - TTI-MSA      USB 2.0 Mobile Disk     FF04091900068
>  - Class: (from Interface) Mass Storage
>  - PacketSize: 64  Configurations: 1
>  - Vendor: 0x126f  Product 0x1325 Version 1.0
>   Configuration: 1
>   - Interfaces: 1 Bus Powered 100mA
>   - ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
>
>     Interface: 0
>     - Alternate Setting 0, Endpoints: 3
>     - Class Mass Storage, Transp. SCSI, Bulk only
>     - ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
>
>     - Endpoint 1 In Bulk MaxPacket 64
>     - Endpoint 2 Out Bulk MaxPacket 64
>     - Endpoint 3 In Interrupt MaxPacket 2 Interval 1ms
>
> DUnf-Boot2009> usb storage
>  Device 0: Vendor:  Rev:  Prod:
>            Type: Removable Hard Disk
>            Capacity: not available
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
>

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-14 21:30   ` Paal Bakken
@ 2009-01-14 21:24     ` Jean-Christophe PLAGNIOL-VILLARD
  2009-01-15 10:27       ` Paal Bakken
  0 siblings, 1 reply; 8+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-01-14 21:24 UTC (permalink / raw)
  To: u-boot

On 22:30 Wed 14 Jan     , Paal Bakken wrote:
> I have testet a lot more and have found the following:
> 
> 1. I tried an old USB 1.0 stick, but got the same bad result...
> 
> 2. Then I took that USB 1.0 stick and deleted multiple partitions with linux fdisk and created a single bootable FAT32 partition. This variant worked without any problems in u-boot. (the multiple partitions seems to be typical from the vendors)
> 
> 3. Then I took the USB 2.0 stick (from the trace in my first mail) and did the same repartioning with fdisk. But this stick still gives the same bad result :-(
> 
> So????
> 
> Are there any known limitations/requirements to the u-boot USB implementation?
> -USB1.0 vs USB2.0
> -How to partition the stick (if the original partition can't be used)
> -Other
> 
> ...and once more: the USB 2.0 stick works fine in linux....
I'll take a look on my 9263ek

but I've test recently a 4GB usb 2.0 key on the at91rm9200ek with any problem

btw please limit your mail at 80chars per line

Best Regards,
J.

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-14 18:53 ` Remy Bohmer
@ 2009-01-14 21:30   ` Paal Bakken
  2009-01-14 21:24     ` Jean-Christophe PLAGNIOL-VILLARD
  2009-01-16 16:30   ` Stelian Pop
  1 sibling, 1 reply; 8+ messages in thread
From: Paal Bakken @ 2009-01-14 21:30 UTC (permalink / raw)
  To: u-boot

I have testet a lot more and have found the following:

1. I tried an old USB 1.0 stick, but got the same bad result...

2. Then I took that USB 1.0 stick and deleted multiple partitions with linux fdisk and created a single bootable FAT32 partition. This variant worked without any problems in u-boot. (the multiple partitions seems to be typical from the vendors)

3. Then I took the USB 2.0 stick (from the trace in my first mail) and did the same repartioning with fdisk. But this stick still gives the same bad result :-(

So????

Are there any known limitations/requirements to the u-boot USB implementation?
-USB1.0 vs USB2.0
-How to partition the stick (if the original partition can't be used)
-Other

...and once more: the USB 2.0 stick works fine in linux....

Best regards 
P?l Bakken

> From: Remy Bohmer [linux at bohmer.net]
> Sent: 2009-01-14 19:53:29 CET
> To: Paal Bakken [pabakken at online.no]
> Cc: u-boot at lists.denx.de, Stelian Pop [stelian at popies.net]
> Subject: Re: [U-Boot] Problems with USB mass storage on at91sam9263
> 
> Hello,
> 
> 2009/1/14 Paal Bakken <pabakken@online.no>:
> > I have problems with usb mass storage in u-boot.
> > We have our own at91sam9263 board, but I experience exactly the same problems on the standard at91sam9263ek. And the usb-port AND memory stick works fine in linux. I have tried both FAT and FAT32. Below follows an edited screendump of some usb commands with a u-boot snapshot version from 13.01.2009.
> 
> The current version should work, indeed a lot has been done in that
> area for these cores. However, IIRC there were some problems with the
> bootstrap code not initialising the PLLB correctly, which resulted in
> similar errors. I thought that Stelian got it to work finally on this
> particular core as well, so maybe he can confirm this. (I concentrated
> the patches on the sam9261)
> 
> Kind Regards,
> 
> Remy
> 
> > (Re)start USB...
> > USB:   scanning bus for devices... 2 USB Device(s) found
> >       scanning bus for storage devices... ERROR:  USB-error: STALL: TD was moved to the Done Queue because the endpoint returned a STALL PID (4)
> > ERROR: USB-error: STALL: TD was moved to the Done Queue because the endpoint returned a STALL PID (4)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > :
> >        225 more of the same error? :-)
> > :
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5) Device NOT ready
> >   Request Sense returned 00 00 00
> > 1 Storage Device(s) found
> >
> > DUnf-Boot2009> usb tree
> >
> > Device Tree:
> >  1  Hub (12MBit/s, 0mA)
> >  |   OHCI Root Hub
> >  |
> >  |?-2  Mass Storage (12MBit/s, 100mA)
> >       TTI-MSA      USB 2.0 Mobile Disk     FF04091900068
> >
> > DUnf-Boot2009> usb info
> >
> > 1: Hub,  USB Revision 1.10
> >  -  OHCI Root Hub
> >  - Class: Hub
> >  - PacketSize: 8  Configurations: 1
> >  - Vendor: 0x0000  Product 0x0000 Version 0.0
> >   Configuration: 1
> >   - Interfaces: 1 Self Powered 0mA
> >     Interface: 0
> >     - Alternate Setting 0, Endpoints: 1
> >     - Class Hub
> >     - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms
> >
> > 2: Mass Storage,  USB Revision 2.0
> >  - TTI-MSA      USB 2.0 Mobile Disk     FF04091900068
> >  - Class: (from Interface) Mass Storage
> >  - PacketSize: 64  Configurations: 1
> >  - Vendor: 0x126f  Product 0x1325 Version 1.0
> >   Configuration: 1
> >   - Interfaces: 1 Bus Powered 100mA
> >   - ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> >
> >     Interface: 0
> >     - Alternate Setting 0, Endpoints: 3
> >     - Class Mass Storage, Transp. SCSI, Bulk only
> >     - ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> > ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
> >
> >     - Endpoint 1 In Bulk MaxPacket 64
> >     - Endpoint 2 Out Bulk MaxPacket 64
> >     - Endpoint 3 In Interrupt MaxPacket 2 Interval 1ms
> >
> > DUnf-Boot2009> usb storage
> >  Device 0: Vendor:  Rev:  Prod:
> >            Type: Removable Hard Disk
> >            Capacity: not available
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot
> >
> >
> 

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-14 21:24     ` Jean-Christophe PLAGNIOL-VILLARD
@ 2009-01-15 10:27       ` Paal Bakken
  2009-01-15 12:03         ` Remy Bohmer
  0 siblings, 1 reply; 8+ messages in thread
From: Paal Bakken @ 2009-01-15 10:27 UTC (permalink / raw)
  To: u-boot

More testing....

It seems like I have one stick that generates the reported error. And this is of course THE one I have been testing with (Murphy is never resting...)

I have tried with four devices now
USB 1.0 128MB : Had to repartition
USB 2.0 512MB : Gives the reported problems (fine in linux and windows)
USB 2.0 2GB : Works without partitioning
USB 2.0 16GB: Works without partitioning

The response is the same on our own at91sam9263 board with 18.432MHz ocillator and the original at91sam9263ek with 16.36766MHz

So - I'm willing to rest my case :-) BUT there is something strange, since the "bad" stick works fine in Linux and Windows... 
-Any ideas about possible reasons for the difference? 
-Is there any specific known requirements for the sticks (except for FAT)


Best regards
P?l Bakken


> From: Jean-Christophe PLAGNIOL-VILLARD [plagnioj at jcrosoft.com]
> Sent: 2009-01-14 22:24:22 CET
> To: Paal Bakken [pabakken at online.no]
> Cc: Remy Bohmer [linux at bohmer.net], u-boot at lists.denx.de
> Subject: Re: [U-Boot] Problems with USB mass storage on at91sam9263
> 
> On 22:30 Wed 14 Jan     , Paal Bakken wrote:
> > I have testet a lot more and have found the following:
> > 
> > 1. I tried an old USB 1.0 stick, but got the same bad result...
> > 
> > 2. Then I took that USB 1.0 stick and deleted multiple partitions with linux fdisk and created a single bootable FAT32 partition. This variant worked without any problems in u-boot. (the multiple partitions seems to be typical from the vendors)
> > 
> > 3. Then I took the USB 2.0 stick (from the trace in my first mail) and did the same repartioning with fdisk. But this stick still gives the same bad result :-(
> > 
> > So????
> > 
> > Are there any known limitations/requirements to the u-boot USB implementation?
> > -USB1.0 vs USB2.0
> > -How to partition the stick (if the original partition can't be used)
> > -Other
> > 
> > ...and once more: the USB 2.0 stick works fine in linux....
> I'll take a look on my 9263ek
> 
> but I've test recently a 4GB usb 2.0 key on the at91rm9200ek with any problem
> 
> btw please limit your mail at 80chars per line
> 
> Best Regards,
> J.
> 

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-15 10:27       ` Paal Bakken
@ 2009-01-15 12:03         ` Remy Bohmer
  2009-01-15 13:43           ` Paal Bakken
  0 siblings, 1 reply; 8+ messages in thread
From: Remy Bohmer @ 2009-01-15 12:03 UTC (permalink / raw)
  To: u-boot

Hello,

> So - I'm willing to rest my case :-) BUT there is something strange, since the "bad" stick works fine in Linux and Windows...
> -Any ideas about possible reasons for the difference?

There has been many improvements to the USB stack lately that at least
it works nowadays on these cores.
However, there are still a number of bugs to solve, so we are not there yet.
Besides, the USB stack only supports a single device at a time, and
does not really support hotplug, it is a completely different USB
stick than Linux is currently using.
The FAT driver also only supports read-only.

So, you cannot really compare the U-boot USB stack with the Linux/Windows stack.
It shows, however, that there are still bugs in the U-boot USB/FAT code.

> -Is there any specific known requirements for the sticks (except for FAT)

FAT32 and VFAT should also work, but if I knew the exact
'requirements', I also knew how to solve the bugs...


Kind Regards,

Remy

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-15 12:03         ` Remy Bohmer
@ 2009-01-15 13:43           ` Paal Bakken
  0 siblings, 0 replies; 8+ messages in thread
From: Paal Bakken @ 2009-01-15 13:43 UTC (permalink / raw)
  To: u-boot

I also found another non-working stick.... This one was also a first generation USB 2.0 stick.

But anyway - It seems like you guys has done a great job and made usb mass storage useful! A few non-working sticks is good enough for me :-)

Best regards

P?l Bakken



> From: Remy Bohmer [linux at bohmer.net]
> Sent: 2009-01-15 13:03:20 CET
> To: Paal Bakken [pabakken at online.no]
> Cc: Jean-Christophe PLAGNIOL-VILLARD [plagnioj at jcrosoft.com], u-boot at lists.denx.de
> Subject: Re: [U-Boot] Problems with USB mass storage on at91sam9263
> 
> Hello,
> 
> > So - I'm willing to rest my case :-) BUT there is something strange, since the "bad" stick works fine in Linux and Windows...
> > -Any ideas about possible reasons for the difference?
> 
> There has been many improvements to the USB stack lately that at least
> it works nowadays on these cores.
> However, there are still a number of bugs to solve, so we are not there yet.
> Besides, the USB stack only supports a single device at a time, and
> does not really support hotplug, it is a completely different USB
> stick than Linux is currently using.
> The FAT driver also only supports read-only.
> 
> So, you cannot really compare the U-boot USB stack with the Linux/Windows stack.
> It shows, however, that there are still bugs in the U-boot USB/FAT code.
> 
> > -Is there any specific known requirements for the sticks (except for FAT)
> 
> FAT32 and VFAT should also work, but if I knew the exact
> 'requirements', I also knew how to solve the bugs...
> 
> 
> Kind Regards,
> 
> Remy
> 

^ permalink raw reply	[flat|nested] 8+ messages in thread
* [U-Boot] Problems with USB mass storage on at91sam9263
  2009-01-14 18:53 ` Remy Bohmer
  2009-01-14 21:30   ` Paal Bakken
@ 2009-01-16 16:30   ` Stelian Pop
  1 sibling, 0 replies; 8+ messages in thread
From: Stelian Pop @ 2009-01-16 16:30 UTC (permalink / raw)
  To: u-boot

On Wed, Jan 14, 2009 at 07:53:29PM +0100, Remy Bohmer wrote:

> Hello,

Hi,

> 
> 2009/1/14 Paal Bakken <pabakken@online.no>:
> > I have problems with usb mass storage in u-boot.
> > We have our own at91sam9263 board, but I experience exactly the same problems on the standard at91sam9263ek. And the usb-port AND memory stick works fine in linux. I have tried both FAT and FAT32. Below follows an edited screendump of some usb commands with a u-boot snapshot version from 13.01.2009.
> 
> The current version should work, indeed a lot has been done in that
> area for these cores. However, IIRC there were some problems with the
> bootstrap code not initialising the PLLB correctly, which resulted in
> similar errors. I thought that Stelian got it to work finally on this
> particular core as well, so maybe he can confirm this. (I concentrated
> the patches on the sam9261)

I do reproduce exactly the same kind of problems here. As I originally said
in my October 9 mail (Message-Id: <1223564465.6130.20.camel@galileo>),
correcting the bootstrap PLLB settings made USB work, but USB storage
did work only with one of my three USB sticks.

I suspect the rest of the issues to be USB specific and not hardware
specific at this point, but I haven't looked closer into it.

Stelian.
-- 
Stelian Pop <stelian@popies.net>

^ permalink raw reply	[flat|nested] 8+ messages in thread
end of thread, other threads:[~2009-01-16 16:30 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-01-14 11:06 [U-Boot] Problems with USB mass storage on at91sam9263 Paal Bakken
2009-01-14 18:53 ` Remy Bohmer
2009-01-14 21:30   ` Paal Bakken
2009-01-14 21:24     ` Jean-Christophe PLAGNIOL-VILLARD
2009-01-15 10:27       ` Paal Bakken
2009-01-15 12:03         ` Remy Bohmer
2009-01-15 13:43           ` Paal Bakken
2009-01-16 16:30   ` Stelian Pop

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox