[U-Boot] [PATCH v2] OMAP3: Update Overo pin mux for new expansion board

[U-Boot] [PATCH v2] OMAP3: Update Overo pin mux for new expansion board

[Dirk Behme]

A new Overo expansion board uses GPIO 14, 21, 22 and 23 for LED's and
switches. This patch changes the pinmux configuration for those pins.
They were previously set up for unused MMC3_DAT4-7.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
---

Changes in v2:

- Add Dirk's Signed-off-by
- Rebase against U-Boot mainline commit
  2344bb8de2354101a8264c2123303c9d8d2aed3c
  'inka4x0: Use proper accessor macros for memory mapped registers.'

This v2 version makes any previous version of this patch obsolete.

 board/omap3/overo/overo.h |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

Index: u-boot-main/board/omap3/overo/overo.h
===================================================================
--- u-boot-main.orig/board/omap3/overo/overo.h
+++ u-boot-main/board/omap3/overo/overo.h
@@ -185,6 +185,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | DIS | M0)) /*CSI2_DX0*/\
  MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | DIS | M0)) /*CSI2_DY0*/\
  MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | EN  | M4)) /*GPIO_114*/\
+							 /* - PEN_DOWN*/\
  MUX_VAL(CP(CSI2_DY1),		(IEN  | PTU | EN  | M4)) /*GPIO_115*/\
  /*Audio Interface */\
  MUX_VAL(CP(MCBSP2_FSX),	(IEN  | PTD | DIS | M0)) /*McBSP2_FSX*/\
@@ -295,7 +296,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(SYS_CLKOUT2),	(IEN  | PTU | EN  | M4)) /*GPIO_186*/\
  MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | EN  | M2)) /*MMC3_CLK*/\
  MUX_VAL(CP(ETK_CTL_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_CMD*/\
- MUX_VAL(CP(ETK_D0_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT4*/\
+ MUX_VAL(CP(ETK_D0_ES2),	(IEN  | PTU | EN  | M4)) /*GPIO_14*/\
  MUX_VAL(CP(ETK_D1_ES2),	(IEN  | PTD | EN  | M4)) /*GPIO_15 - X_GATE*/\
  MUX_VAL(CP(ETK_D2_ES2),	(IEN  | PTU | EN  | M4)) /*GPIO_16*/\
 							 /* - W2W_NRESET*/\
@@ -303,9 +304,9 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(ETK_D4_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT0*/\
  MUX_VAL(CP(ETK_D5_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT1*/\
  MUX_VAL(CP(ETK_D6_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT2*/\
- MUX_VAL(CP(ETK_D7_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT7*/\
- MUX_VAL(CP(ETK_D8_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT6*/\
- MUX_VAL(CP(ETK_D9_ES2),	(IEN  | PTU | EN  | M2)) /*MMC3_DAT5*/\
+ MUX_VAL(CP(ETK_D7_ES2),	(IEN  | PTU | EN  | M4)) /*GPIO_21*/\
+ MUX_VAL(CP(ETK_D8_ES2),	(IEN  | PTU | EN  | M4)) /*GPIO_22*/\
+ MUX_VAL(CP(ETK_D9_ES2),	(IEN  | PTU | EN  | M4)) /*GPIO_23*/\
  MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
  MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
  MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M3)) /*HSUSB2_DIR*/\

[U-Boot] [PATCH v2] OMAP3: Update Overo pin mux for new expansion board

[Jean-Christophe PLAGNIOL-VILLARD]

On 21:15 Mon 30 Mar     , Dirk Behme wrote:
> A new Overo expansion board uses GPIO 14, 21, 22 and 23 for LED's and
> switches. This patch changes the pinmux configuration for those pins.
> They were previously set up for unused MMC3_DAT4-7.
> 
> Signed-off-by: Steve Sakoman <steve@sakoman.com>
> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
> ---
> 
Apply
> Changes in v2:
> 
> - Add Dirk's Signed-off-by
> - Rebase against U-Boot mainline commit
>   2344bb8de2354101a8264c2123303c9d8d2aed3c
>   'inka4x0: Use proper accessor macros for memory mapped registers.'
when you rebase a code you MUST let the orignal Author as patch Author
please use stgit or any other tools for this

Best Regards,
J.