[U-Boot] [PATCH 2/7] serial_mx31: allow it to work with mx27 too and rename to serial_mxc

[Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>]

On 04:12 Mon 08 Jun     , Ilya Yanok wrote:
> UART hardware on i.MX27 is the same as on the i.MX31 so we just
> need to provide the driver with correct address of the registers.
> 
IIRC the imx1 share the same too
> Signed-off-by: Ilya Yanok <yanok@emcraft.com>
> ---
>  drivers/serial/Makefile                        |    2 +-
>  drivers/serial/{serial_mx31.c => serial_mxc.c} |   21 +++++++++++++++++++++
>  include/configs/imx31_litekit.h                |    2 +-
>  include/configs/imx31_phycore.h                |    2 +-
>  include/configs/mx31ads.h                      |    2 +-
>  include/configs/qong.h                         |    2 +-
>  6 files changed, 26 insertions(+), 5 deletions(-)
>  rename drivers/serial/{serial_mx31.c => serial_mxc.c} (94%)
> 
> diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
> index 14c818d..9a572e9 100644
> --- a/drivers/serial/Makefile
> +++ b/drivers/serial/Makefile
> @@ -40,7 +40,7 @@ COBJS-$(CONFIG_IXP_SERIAL) += serial_ixp.o
>  COBJS-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o
>  COBJS-$(CONFIG_LPC2292_SERIAL) += serial_lpc2292.o
>  COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
> -COBJS-$(CONFIG_MX31_UART) += serial_mx31.o
> +COBJS-$(CONFIG_MXC_UART) += serial_mxc.o
>  COBJS-$(CONFIG_NETARM_SERIAL) += serial_netarm.o
>  COBJS-$(CONFIG_PL010_SERIAL) += serial_pl01x.o
>  COBJS-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
> diff --git a/drivers/serial/serial_mx31.c b/drivers/serial/serial_mxc.c
> similarity index 94%
> rename from drivers/serial/serial_mx31.c
> rename to drivers/serial/serial_mxc.c
> index 7c0682a..acc5b7d 100644
> --- a/drivers/serial/serial_mx31.c
> +++ b/drivers/serial/serial_mxc.c
> @@ -18,7 +18,12 @@
>   */
>  
>  #include <common.h>
> +#ifdef CONFIG_MX31
>  #include <asm/arch/mx31.h>
> +#else
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/clock.h>
> +#endif
>  
>  #define __REG(x)     (*((volatile u32 *)(x)))
>  
> @@ -32,6 +37,18 @@
>  #define UART_PHYS 0x43fb0000
>  #elif defined(CONFIG_SYS_MX31_UART5)
>  #define UART_PHYS 0x43fb4000
> +#elif defined(CONFIG_SYS_MX27_UART1)
> +#define UART_PHYS 0x1000a000
> +#elif defined(CONFIG_SYS_MX27_UART2)
> +#define UART_PHYS 0x1000b000
> +#elif defined(CONFIG_SYS_MX27_UART3)
> +#define UART_PHYS 0x1000c000
> +#elif defined(CONFIG_SYS_MX27_UART4)
> +#define UART_PHYS 0x1000d000
> +#elif defined(CONFIG_SYS_MX27_UART5)
> +#define UART_PHYS 0x1001b000
> +#elif defined(CONFIG_SYS_MX27_UART6)
> +#define UART_PHYS 0x1001c000
>  #else
>  #error "define CONFIG_SYS_MX31_UARTx to use the mx31 UART driver"
>  #endif
> @@ -149,7 +166,11 @@ DECLARE_GLOBAL_DATA_PTR;
>  
>  void serial_setbrg (void)
>  {
> +#ifdef CONFIG_MX31
>  	u32 clk = mx31_get_ipg_clk();
> +#else
> +	u32 clk = imx_get_perclk1();
> +#endif
here we need to have a common clock rate function name as we do for avr32 &
at91

	this could done in a next patch but mandatory for other board adding

applied to u-boot-arm

Best Regards,
J.