[U-Boot] [PATCH 2/4] OMAP3 pandora: setup pin mux for pins used on rev3 boards

Grazvydas Ignotas
2009-07-07T21:29:59Z

Setup pin mux for GPIO pins connected on rev3 or later
boards. Also change NUB2 IRQ pin. This should not affect
older boards because they don't have any nubs (analog
controllers) attached to them.
---
board/omap3/pandora/pandora.h | 11 ++++++++++-
1 files changed, 10 insertions(+), 1 deletions(-)

diff --git a/board/omap3/pandora/pandora.h b/board/omap3/pandora/pandora.h
index 3d04b2a..1bd3d30 100644
--- a/board/omap3/pandora/pandora.h
+++ b/board/omap3/pandora/pandora.h
@@ -242,13 +242,15 @@ const omap3_sysinfo sysinfo = {
/* - WIFI_IRQ*/\
MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M4)) /*GPIO_161*/\
/* - nIRQ_NUB1*/\
- MUX_VAL(CP(CAM_WEN), (IEN | PTU | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTU | DIS | M4)) /*GPIO_162*/\
/* - nIRQ_NUB2*/\
/*Various other stuff*/\
MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | DIS | M4)) /*GPIO_163*/\
/* - nOC_USB5*/\
MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | DIS | M4)) /*GPIO_22*/\
/* - MSECURE*/\
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M4)) /*GPIO_115*/\
+ /* - POP_OVERHEAT*/\
/*External Resets and Enables*/\
MUX_VAL(CP(ETK_D0_ES2), (IDIS | PTD | DIS | M4)) /*GPIO_14*/\
/* - nHDPHN_SHUTDOWN*/\
@@ -262,6 +264,13 @@ const omap3_sysinfo sysinfo = {
/* - RESET_NUBS*/\
MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTU | EN | M4)) /*GPIO_164*/\
/* - EN_USB_5V*/\
+ /*Spare GPIOs*/\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTD | EN | M4)) /*GPIO_58*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTD | EN | M4)) /*GPIO_64*/\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTD | EN | M4)) /*GPIO_65*/\
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M4)) /*GPIO_95*/\
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | EN | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(HDQ_SIO), (IEN | PTD | EN | M4)) /*GPIO_170*/\
/*HS USB OTG Port (connects to HSUSB0)*/\
MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
--
1.5.6.3