* [U-Boot] [PATCH 2/7] PXA: pxafb: Add ACX517AKN support
2010-07-22 15:03 [U-Boot] [PATCH 1/7] ARM: Define __raw_readX and __raw_writeX Marek Vasut
@ 2010-07-22 15:03 ` Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 3/7] common: Enable serial for PXA250 Marek Vasut
` (4 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Marek Vasut @ 2010-07-22 15:03 UTC (permalink / raw)
To: u-boot
ACX517AKN LCD panel is found in Palm Tungsten|C
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
arch/arm/cpu/pxa/pxafb.c | 34 ++++++++++++++++++++++++++++++++++
1 files changed, 34 insertions(+), 0 deletions(-)
diff --git a/arch/arm/cpu/pxa/pxafb.c b/arch/arm/cpu/pxa/pxafb.c
index 524a03b..328fa7a 100644
--- a/arch/arm/cpu/pxa/pxafb.c
+++ b/arch/arm/cpu/pxa/pxafb.c
@@ -215,6 +215,40 @@ vidinfo_t panel_info = {
/*----------------------------------------------------------------------*/
+#ifdef CONFIG_ACX517AKN
+
+# define LCD_BPP LCD_COLOR8
+
+/* you have to set lccr0 and lccr3 (including pcd) */
+# define REG_LCCR0 0x003008f9
+# define REG_LCCR3 0x03700006
+
+vidinfo_t panel_info = {
+ vl_col: 320,
+ vl_row: 320,
+ vl_width: 320,
+ vl_height: 320,
+ vl_clkp: CONFIG_SYS_HIGH,
+ vl_oep: CONFIG_SYS_LOW,
+ vl_hsp: CONFIG_SYS_LOW,
+ vl_vsp: CONFIG_SYS_LOW,
+ vl_dp: CONFIG_SYS_HIGH,
+ vl_bpix: LCD_BPP,
+ vl_lbw: 0,
+ vl_splt: 1,
+ vl_clor: 1,
+ vl_tft: 1,
+ vl_hpw: 0x04,
+ vl_blw: 0x1c,
+ vl_elw: 0x08,
+ vl_vpw: 0x01,
+ vl_bfw: 0x07,
+ vl_efw: 0x08,
+};
+#endif /* CONFIG_ACX517AKN */
+
+/*----------------------------------------------------------------------*/
+
#if LCD_BPP == LCD_COLOR8
void lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue);
#endif
--
1.7.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [U-Boot] [PATCH 3/7] common: Enable serial for PXA250
2010-07-22 15:03 [U-Boot] [PATCH 1/7] ARM: Define __raw_readX and __raw_writeX Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 2/7] PXA: pxafb: Add ACX517AKN support Marek Vasut
@ 2010-07-22 15:03 ` Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 4/7] PXA: Palm Tungsten|C Support Marek Vasut
` (3 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Marek Vasut @ 2010-07-22 15:03 UTC (permalink / raw)
To: u-boot
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
common/serial.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/common/serial.c b/common/serial.c
index fceabfa..7148cb9 100644
--- a/common/serial.c
+++ b/common/serial.c
@@ -30,7 +30,7 @@ DECLARE_GLOBAL_DATA_PTR;
static struct serial_device *serial_devices = NULL;
static struct serial_device *serial_current = NULL;
-#if !defined(CONFIG_LWMON) && !defined(CONFIG_PXA27X)
+#if !defined(CONFIG_LWMON) && !defined(CONFIG_PXA27X) && !defined(CONFIG_PXA250)
struct serial_device *__default_serial_console (void)
{
#if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2)
--
1.7.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [U-Boot] [PATCH 4/7] PXA: Palm Tungsten|C Support
2010-07-22 15:03 [U-Boot] [PATCH 1/7] ARM: Define __raw_readX and __raw_writeX Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 2/7] PXA: pxafb: Add ACX517AKN support Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 3/7] common: Enable serial for PXA250 Marek Vasut
@ 2010-07-22 15:03 ` Marek Vasut
2010-08-03 21:10 ` Wolfgang Denk
2010-07-22 15:03 ` [U-Boot] [PATCH 5/7] PXA: pxafb: Add support for Sharp LQ038J7DH53 Marek Vasut
` (2 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Marek Vasut @ 2010-07-22 15:03 UTC (permalink / raw)
To: u-boot
This patch adds support for the Palm Tungsten|C PXA255 board. The support
includes:
- LCD
- MMC
- UART
- NOR
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
board/palmtc/Makefile | 54 +++++++++
board/palmtc/config.mk | 3 +
board/palmtc/lowlevel_init.S | 40 +++++++
board/palmtc/palmtc.c | 77 +++++++++++++
board/palmtc/u-boot.lds | 56 ++++++++++
boards.cfg | 1 +
include/configs/palmtc.h | 250 ++++++++++++++++++++++++++++++++++++++++++
7 files changed, 481 insertions(+), 0 deletions(-)
create mode 100644 board/palmtc/Makefile
create mode 100644 board/palmtc/config.mk
create mode 100644 board/palmtc/lowlevel_init.S
create mode 100644 board/palmtc/palmtc.c
create mode 100644 board/palmtc/u-boot.lds
create mode 100644 include/configs/palmtc.h
diff --git a/board/palmtc/Makefile b/board/palmtc/Makefile
new file mode 100644
index 0000000..92e5288
--- /dev/null
+++ b/board/palmtc/Makefile
@@ -0,0 +1,54 @@
+
+#
+# Copyright (C) 2009
+# Marek Vasut <marek.vasut@gmail.com>
+#
+# Heavily based on pxa255_idp platform
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := palmtc.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/palmtc/config.mk b/board/palmtc/config.mk
new file mode 100644
index 0000000..bcb42e7
--- /dev/null
+++ b/board/palmtc/config.mk
@@ -0,0 +1,3 @@
+#TEXT_BASE = 0xa1700000
+TEXT_BASE = 0xa1000000
+#TEXT_BASE = 0
diff --git a/board/palmtc/lowlevel_init.S b/board/palmtc/lowlevel_init.S
new file mode 100644
index 0000000..72c4441
--- /dev/null
+++ b/board/palmtc/lowlevel_init.S
@@ -0,0 +1,40 @@
+/*
+ * Palm Tungsten|C Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ pxa_gpio_setup
+ pxa_wait_ticks 0x8000
+ pxa_mem_setup
+ pxa_wakeup
+ pxa_intr_setup
+ pxa_clock_setup
+
+ mov pc, lr
diff --git a/board/palmtc/palmtc.c b/board/palmtc/palmtc.c
new file mode 100644
index 0000000..17528b7
--- /dev/null
+++ b/board/palmtc/palmtc.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2009
+ * Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Heavily based on pxa255_idp platform
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <serial.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ /* memory and cpu-speed are setup before relocation */
+ /* so we do _nothing_ here */
+
+ /* arch number of Lubbock-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_PALMTC;
+
+ /* Adress of boot parameters */
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ /* Set PWM for LCD */
+ PWM_CTRL1 = 0x5f;
+ PWM_PERVAL1 = 0x3ff;
+ PWM_PWDUTY1 = 892;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_LCD
+ setenv("stdout", "lcd");
+ setenv("stderr", "lcd");
+#else
+ setenv("stdout", "serial");
+ setenv("stderr", "serial");
+#endif
+ return 0;
+}
+
+struct serial_device *default_serial_console (void)
+{
+ return &serial_ffuart_device;
+}
+
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+ return 0;
+}
diff --git a/board/palmtc/u-boot.lds b/board/palmtc/u-boot.lds
new file mode 100644
index 0000000..fb4358b
--- /dev/null
+++ b/board/palmtc/u-boot.lds
@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/pxa/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
+ _end = .;
+}
diff --git a/boards.cfg b/boards.cfg
index b82f530..2af8d20 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -59,6 +59,7 @@ delta arm pxa
innokom arm pxa
logodl arm pxa
lubbock arm pxa
+palmtc arm pxa
pleb2 arm pxa
xaeniax arm pxa
xm250 arm pxa
diff --git a/include/configs/palmtc.h b/include/configs/palmtc.h
new file mode 100644
index 0000000..6f05cb2
--- /dev/null
+++ b/include/configs/palmtc.h
@@ -0,0 +1,250 @@
+/*
+ * Copyright (C) 2009-2010
+ * Marek Vasut <marek.vasut@gmail.com>
+ * Configuration settings for Palm Tungsten|C
+ *
+ * Heavily based on pxa255_idp platform
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/pxa-regs.h>
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_PXA250 1 /* Intel PXA255 CPU */
+#define CONFIG_PALMTC 1 /* Palm Tungsten|C board */
+
+#undef BOARD_LATE_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#undef CONFIG_USE_IRQ
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_SIZE 0x40000
+
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + CONFIG_STACKSIZE)
+#define CONFIG_SYS_GBL_DATA_SIZE 512
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinfo && fatload mmc 0 0xa0000000 uboot.script ; then " \
+ "source 0xa0000000; " \
+ "else " \
+ "bootm 0x80000; " \
+ "fi; "
+#define CONFIG_BOOTARGS \
+ "console=tty0 console=ttyS0,57600"
+#define CONFIG_TIMESTAMP
+#define CONFIG_BOOTDELAY 2 /* Autoboot delay */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+#define CONFIG_LZMA /* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ * STUART - the lower serial port on Colibri board
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_NET
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MMC
+#define CONFIG_LCD
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_PXA_MMC_GENERIC
+#define CONFIG_SYS_MMC_BASE 0xF0000000
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_ACX517AKN
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CMD_BMP
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
+#else
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#endif
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/*
+ * Clock Configuration
+ */
+#undef CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ 3686400 /* Timer @ 3686400 Hz */
+#define CONFIG_SYS_CPUSPEED 0x161 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* We have 1 bank of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_DRAM_BASE
+
+/*
+ * NOR FLASH
+ */
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_32BIT
+
+#define CONFIG_SYS_MONITOR_BASE 0x0
+#define CONFIG_SYS_MONITOR_LEN 0x40000
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 64
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_LOCK_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT (2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_PROTECTION
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GAFR0_L_VAL 0x00011004
+#define CONFIG_SYS_GAFR0_U_VAL 0xa5000008
+#define CONFIG_SYS_GAFR1_L_VAL 0x60888050
+#define CONFIG_SYS_GAFR1_U_VAL 0xaaa50aaa
+#define CONFIG_SYS_GAFR2_L_VAL 0x0aaaaaaa
+#define CONFIG_SYS_GAFR2_U_VAL 0x00000000
+#define CONFIG_SYS_GPCR0_VAL 0x0
+#define CONFIG_SYS_GPCR1_VAL 0x0
+#define CONFIG_SYS_GPCR2_VAL 0x0
+#define CONFIG_SYS_GPDR0_VAL 0xcfff8140
+#define CONFIG_SYS_GPDR1_VAL 0xfcbfbef3
+#define CONFIG_SYS_GPDR2_VAL 0x0001ffff
+#define CONFIG_SYS_GPSR0_VAL 0x00010f8f
+#define CONFIG_SYS_GPSR1_VAL 0x00bf5de5
+#define CONFIG_SYS_GPSR2_VAL 0x03fe0800
+
+#define CONFIG_SYS_PSSR_VAL PSSR_RDH
+
+/* Clock setup:
+ * CKEN[1] - PWM1
+ * CKEN[6] - FFUART
+ * CKEN[12] - MMC
+ * CKEN[16] - LCD
+ */
+#define CONFIG_SYS_CKEN 0x00011042
+#define CONFIG_SYS_CCCR 0x00000161
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x800092c2
+#define CONFIG_SYS_MSC1_VAL 0x80008000
+#define CONFIG_SYS_MSC2_VAL 0x80008000
+#define CONFIG_SYS_MDCNFG_VAL 0x00001ac9
+#define CONFIG_SYS_MDREFR_VAL 0x00118018
+#define CONFIG_SYS_MDMRS_VAL 0x00220032
+#define CONFIG_SYS_FLYCNFG_VAL 0x01fe01fe
+#define CONFIG_SYS_SXCNFG_VAL 0x00000000
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000000
+#define CONFIG_SYS_MCMEM0_VAL 0x00010504
+#define CONFIG_SYS_MCMEM1_VAL 0x00010504
+#define CONFIG_SYS_MCATT0_VAL 0x00010504
+#define CONFIG_SYS_MCATT1_VAL 0x00010504
+#define CONFIG_SYS_MCIO0_VAL 0x00010e04
+#define CONFIG_SYS_MCIO1_VAL 0x00010e04
+
+#endif /* __CONFIG_H */
--
1.7.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [U-Boot] [PATCH 4/7] PXA: Palm Tungsten|C Support
2010-07-22 15:03 ` [U-Boot] [PATCH 4/7] PXA: Palm Tungsten|C Support Marek Vasut
@ 2010-08-03 21:10 ` Wolfgang Denk
0 siblings, 0 replies; 10+ messages in thread
From: Wolfgang Denk @ 2010-08-03 21:10 UTC (permalink / raw)
To: u-boot
Dear Marek Vasut,
In message <1279811005-21858-4-git-send-email-marek.vasut@gmail.com> you wrote:
> This patch adds support for the Palm Tungsten|C PXA255 board. The support
> includes:
> - LCD
> - MMC
> - UART
> - NOR
>
> Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
> ---
> board/palmtc/Makefile | 54 +++++++++
> board/palmtc/config.mk | 3 +
> board/palmtc/lowlevel_init.S | 40 +++++++
> board/palmtc/palmtc.c | 77 +++++++++++++
> board/palmtc/u-boot.lds | 56 ++++++++++
> boards.cfg | 1 +
> include/configs/palmtc.h | 250 ++++++++++++++++++++++++++++++++++++++++++
> 7 files changed, 481 insertions(+), 0 deletions(-)
> create mode 100644 board/palmtc/Makefile
> create mode 100644 board/palmtc/config.mk
> create mode 100644 board/palmtc/lowlevel_init.S
> create mode 100644 board/palmtc/palmtc.c
> create mode 100644 board/palmtc/u-boot.lds
> create mode 100644 include/configs/palmtc.h
Entries to MAINTAINERS and MAKEALL missing.
> diff --git a/board/palmtc/Makefile b/board/palmtc/Makefile
> new file mode 100644
> index 0000000..92e5288
> --- /dev/null
> +++ b/board/palmtc/Makefile
> @@ -0,0 +1,54 @@
> +
> +#
> +# Copyright (C) 2009
2009?
> --- /dev/null
> +++ b/board/palmtc/config.mk
> @@ -0,0 +1,3 @@
> +#TEXT_BASE = 0xa1700000
> +TEXT_BASE = 0xa1000000
> +#TEXT_BASE = 0
Please remove dead code.
> +int board_init (void)
> +{
> + /* memory and cpu-speed are setup before relocation */
> + /* so we do _nothing_ here */
Incorrect multiline comment style.
> + /* arch number of Lubbock-Board */
> + gd->bd->bi_arch_number = MACH_TYPE_PALMTC;
> +
> + /* Adress of boot parameters */
> + gd->bd->bi_boot_params = 0xa0000100;
> +
> + /* Set PWM for LCD */
> + PWM_CTRL1 = 0x5f;
> + PWM_PERVAL1 = 0x3ff;
> + PWM_PWDUTY1 = 892;
> +
> + return 0;
> +}
> +
> +int board_late_init(void)
> +{
> +#ifdef CONFIG_LCD
> + setenv("stdout", "lcd");
> + setenv("stderr", "lcd");
> +#else
> + setenv("stdout", "serial");
> + setenv("stderr", "serial");
> +#endif
It's a bad idea to force such settings on a user without leaving him
any other choice. We had such discussions before. Please don't.
...
> +#define CONFIG_PXA250 1 /* Intel PXA255 CPU */
> +#define CONFIG_PALMTC 1 /* Palm Tungsten|C board */
> +
> +#undef BOARD_LATE_INIT
> +#undef CONFIG_SKIP_RELOCATE_UBOOT
> +#undef CONFIG_USE_IRQ
> +#undef CONFIG_SKIP_LOWLEVEL_INIT
Please do not undef what is not defined anyway.
> +/*
> + * Environment settings
> + */
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_ENV_IS_IN_FLASH 1
> +#define CONFIG_ENV_ADDR 0x40000
> +#define CONFIG_ENV_SIZE 0x40000
Decide if you use TABs or SPACEs here (SPACEs recommended), but use
that consistently then.
> +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + CONFIG_STACKSIZE)
That looks awfully wrong - the stack has nothing to do with the malloc
arena. If you want to use just the same size (which does not make much
sense to me either), then use aan independent variable for that.
> +#define CONFIG_SYS_GBL_DATA_SIZE 512
Don't! Make as small as possible. You probably do NOT need that much,
or do you?
...
> +#define CONFIG_SYS_CPUSPEED 0x161 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
Line too long. Please fix globally.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
There's an old story about the person who wished his computer were as
easy to use as his telephone. That wish has come true, since I no
longer know how to use my telephone.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 5/7] PXA: pxafb: Add support for Sharp LQ038J7DH53
2010-07-22 15:03 [U-Boot] [PATCH 1/7] ARM: Define __raw_readX and __raw_writeX Marek Vasut
` (2 preceding siblings ...)
2010-07-22 15:03 ` [U-Boot] [PATCH 4/7] PXA: Palm Tungsten|C Support Marek Vasut
@ 2010-07-22 15:03 ` Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 6/7] PXA: Add initial Palm LifeDrive support Marek Vasut
2010-07-22 15:03 ` [U-Boot] [PATCH 7/7] PXA: Vpac270 config fixes Marek Vasut
5 siblings, 0 replies; 10+ messages in thread
From: Marek Vasut @ 2010-07-22 15:03 UTC (permalink / raw)
To: u-boot
This LCD panel is found in Palm LifeDrive handheld
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
arch/arm/cpu/pxa/pxafb.c | 34 ++++++++++++++++++++++++++++++++++
1 files changed, 34 insertions(+), 0 deletions(-)
diff --git a/arch/arm/cpu/pxa/pxafb.c b/arch/arm/cpu/pxa/pxafb.c
index 328fa7a..066f49e 100644
--- a/arch/arm/cpu/pxa/pxafb.c
+++ b/arch/arm/cpu/pxa/pxafb.c
@@ -249,6 +249,40 @@ vidinfo_t panel_info = {
/*----------------------------------------------------------------------*/
+#ifdef CONFIG_LQ038J7DH53
+
+# define LCD_BPP LCD_COLOR8
+
+/* you have to set lccr0 and lccr3 (including pcd) */
+# define REG_LCCR0 0x003008f9
+# define REG_LCCR3 0x03700004
+
+vidinfo_t panel_info = {
+ vl_col: 320,
+ vl_row: 480,
+ vl_width: 320,
+ vl_height: 480,
+ vl_clkp: CONFIG_SYS_HIGH,
+ vl_oep: CONFIG_SYS_LOW,
+ vl_hsp: CONFIG_SYS_LOW,
+ vl_vsp: CONFIG_SYS_LOW,
+ vl_dp: CONFIG_SYS_HIGH,
+ vl_bpix: LCD_BPP,
+ vl_lbw: 0,
+ vl_splt: 1,
+ vl_clor: 1,
+ vl_tft: 1,
+ vl_hpw: 0x04,
+ vl_blw: 0x20,
+ vl_elw: 0x01,
+ vl_vpw: 0x01,
+ vl_bfw: 0x04,
+ vl_efw: 0x01,
+};
+#endif /* CONFIG_ACX517AKN */
+
+/*----------------------------------------------------------------------*/
+
#if LCD_BPP == LCD_COLOR8
void lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue);
#endif
--
1.7.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [U-Boot] [PATCH 6/7] PXA: Add initial Palm LifeDrive support
2010-07-22 15:03 [U-Boot] [PATCH 1/7] ARM: Define __raw_readX and __raw_writeX Marek Vasut
` (3 preceding siblings ...)
2010-07-22 15:03 ` [U-Boot] [PATCH 5/7] PXA: pxafb: Add support for Sharp LQ038J7DH53 Marek Vasut
@ 2010-07-22 15:03 ` Marek Vasut
2010-08-03 21:13 ` Wolfgang Denk
2010-07-22 15:03 ` [U-Boot] [PATCH 7/7] PXA: Vpac270 config fixes Marek Vasut
5 siblings, 1 reply; 10+ messages in thread
From: Marek Vasut @ 2010-07-22 15:03 UTC (permalink / raw)
To: u-boot
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
board/palmld/Makefile | 54 ++++++++
board/palmld/config.mk | 1 +
board/palmld/lowlevel_init.S | 46 +++++++
board/palmld/palmld.c | 81 ++++++++++++
board/palmld/u-boot.lds | 56 +++++++++
boards.cfg | 1 +
include/configs/palmld.h | 275 ++++++++++++++++++++++++++++++++++++++++++
7 files changed, 514 insertions(+), 0 deletions(-)
create mode 100644 board/palmld/Makefile
create mode 100644 board/palmld/config.mk
create mode 100644 board/palmld/lowlevel_init.S
create mode 100644 board/palmld/palmld.c
create mode 100644 board/palmld/u-boot.lds
create mode 100644 include/configs/palmld.h
diff --git a/board/palmld/Makefile b/board/palmld/Makefile
new file mode 100644
index 0000000..c184cf6
--- /dev/null
+++ b/board/palmld/Makefile
@@ -0,0 +1,54 @@
+
+#
+# Copyright (C) 2009
+# Marek Vasut <marek.vasut@gmail.com>
+#
+# Heavily based on pxa255_idp platform
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := palmld.o
+SOBJS := lowlevel_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/palmld/config.mk b/board/palmld/config.mk
new file mode 100644
index 0000000..1d650ac
--- /dev/null
+++ b/board/palmld/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0xa1000000
diff --git a/board/palmld/lowlevel_init.S b/board/palmld/lowlevel_init.S
new file mode 100644
index 0000000..6b6d11f
--- /dev/null
+++ b/board/palmld/lowlevel_init.S
@@ -0,0 +1,46 @@
+/*
+ * Aeronix Zipit Z2 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+ pxa_gpio_setup
+
+ /* Enable GPIO reset */
+ ldr r0, =PCFR
+ mov r1, #0x30
+ str r1, [r0]
+
+ pxa_wait_ticks 0x8000
+ pxa_mem_setup
+ pxa_wakeup
+ pxa_intr_setup
+ pxa_clock_setup
+
+ mov pc, lr
diff --git a/board/palmld/palmld.c b/board/palmld/palmld.c
new file mode 100644
index 0000000..679a47c
--- /dev/null
+++ b/board/palmld/palmld.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright (C) 2009
+ * Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Heavily based on pxa255_idp platform
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <serial.h>
+#include <asm/arch/pxa-regs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ /* memory and cpu-speed are setup before relocation */
+ /* so we do _nothing_ here */
+
+ /* arch number of Lubbock-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_PALMLD;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ /* Set PWM for LCD */
+ PWM_CTRL0 = 0x7;
+ PWM_PERVAL0 = 0x16c;
+ PWM_PWDUTY0 = 0x11a;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ setenv("stdout", "serial");
+ setenv("stderr", "serial");
+ return 0;
+}
+
+struct serial_device *default_serial_console (void)
+{
+ return &serial_ffuart_device;
+}
+
+int dram_init (void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
+{
+ info->portwidth = FLASH_CFI_16BIT;
+ info->chipwidth = FLASH_CFI_BY16;
+ info->interface = FLASH_CFI_X16;
+}
diff --git a/board/palmld/u-boot.lds b/board/palmld/u-boot.lds
new file mode 100644
index 0000000..fb4358b
--- /dev/null
+++ b/board/palmld/u-boot.lds
@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/pxa/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
+ _end = .;
+}
diff --git a/boards.cfg b/boards.cfg
index 2af8d20..4acd3eb 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -59,6 +59,7 @@ delta arm pxa
innokom arm pxa
logodl arm pxa
lubbock arm pxa
+palmld arm pxa
palmtc arm pxa
pleb2 arm pxa
xaeniax arm pxa
diff --git a/include/configs/palmld.h b/include/configs/palmld.h
new file mode 100644
index 0000000..9f0be73
--- /dev/null
+++ b/include/configs/palmld.h
@@ -0,0 +1,275 @@
+/*
+ * Palm LifeDrive configuration file
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_PXA27X 1 /* Marvell PXA270 CPU */
+#define CONFIG_PALMLD 1 /* Palm LifeDrive board */
+
+#undef BOARD_LATE_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#undef CONFIG_USE_IRQ
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + CONFIG_STACKSIZE)
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinfo && fatload mmc 0 0xa0000000 uboot.script ; then " \
+ "source 0xa0000000; " \
+ "else " \
+ "bootm 0x0x60000; " \
+ "fi; "
+#define CONFIG_BOOTARGS "console=tty0 console=ttyS0,115200"
+#define CONFIG_TIMESTAMP
+#define CONFIG_BOOTDELAY 2 /* Autoboot delay */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+#define CONFIG_LZMA /* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART 1
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_NET
+#define CONFIG_CMD_ENV
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_IDE
+#define CONFIG_LCD
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_PXA_MMC_GENERIC
+#define CONFIG_SYS_MMC_BASE 0xF0000000
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_LQ038J7DH53
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CMD_BMP
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
+#else
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#endif
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/*
+ * Clock Configuration
+ */
+#undef CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ 3250000 /* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED 0x210 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* We have 1 bank of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x02000000 /* 32 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_DRAM_BASE
+
+/*
+ * NOR FLASH
+ */
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x00080000 /* 512 KB */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER 1
+
+#define CONFIG_FLASH_CFI_LEGACY
+#define CONFIG_SYS_FLASH_LEGACY_512Kx16
+
+#define CONFIG_SYS_MONITOR_BASE 0
+#define CONFIG_SYS_MONITOR_LEN 0x40000
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_LOCK_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_PROTECTION
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+
+/*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define CONFIG_LBA48
+#undef CONFIG_IDE_LED
+#undef CONFIG_IDE_RESET
+
+/*
+ * HACK WARNING: __io
+ * This MUST go away once the readb/writeb and inb/outb issue is solved
+ */
+#define __io
+
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+
+#define CONFIG_SYS_ATA_BASE_ADDR 0x20000000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0
+
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x10
+#define CONFIG_SYS_ATA_REG_OFFSET 0x10
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x10
+
+#define CONFIG_SYS_ATA_STRIDE 1
+#endif
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GAFR0_L_VAL 0x00000000
+#define CONFIG_SYS_GAFR0_U_VAL 0xa5180012
+#define CONFIG_SYS_GAFR1_L_VAL 0x69988056
+#define CONFIG_SYS_GAFR1_U_VAL 0xaaa580aa
+#define CONFIG_SYS_GAFR2_L_VAL 0x6aaaaaaa
+#define CONFIG_SYS_GAFR2_U_VAL 0x01040001
+#define CONFIG_SYS_GAFR3_L_VAL 0x540a950c
+#define CONFIG_SYS_GAFR3_U_VAL 0x00000009
+#define CONFIG_SYS_GPCR0_VAL 0x00000000
+#define CONFIG_SYS_GPCR1_VAL 0x00000000
+#define CONFIG_SYS_GPCR2_VAL 0x00000000
+#define CONFIG_SYS_GPCR3_VAL 0x00000000
+#define CONFIG_SYS_GPDR0_VAL 0xc26b0000
+#define CONFIG_SYS_GPDR1_VAL 0xfcdfaa93
+#define CONFIG_SYS_GPDR2_VAL 0x7bbaffff
+#define CONFIG_SYS_GPDR3_VAL 0x006ff38d
+#define CONFIG_SYS_GPSR0_VAL 0x0d9e45ee
+#define CONFIG_SYS_GPSR1_VAL 0x03affdae
+#define CONFIG_SYS_GPSR2_VAL 0x07554000
+#define CONFIG_SYS_GPSR3_VAL 0x01bc0785
+
+#define CONFIG_SYS_PSSR_VAL 0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN 0x01ffffff
+#define CONFIG_SYS_CCCR 0x02000210
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x7ff844c8
+#define CONFIG_SYS_MSC1_VAL 0x7ff86ab4
+#define CONFIG_SYS_MSC2_VAL 0x7ff87ff8
+#define CONFIG_SYS_MDCNFG_VAL 0x0B880acd
+#define CONFIG_SYS_MDREFR_VAL 0x201fa031
+#define CONFIG_SYS_MDMRS_VAL 0x00320032
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000003
+#define CONFIG_SYS_MCMEM0_VAL 0x0001c391
+#define CONFIG_SYS_MCMEM1_VAL 0x0001c391
+#define CONFIG_SYS_MCATT0_VAL 0x0001c391
+#define CONFIG_SYS_MCATT1_VAL 0x0001c391
+#define CONFIG_SYS_MCIO0_VAL 0x00014611
+#define CONFIG_SYS_MCIO1_VAL 0x0001c391
+
+#endif /* __CONFIG_H */
--
1.7.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [U-Boot] [PATCH 6/7] PXA: Add initial Palm LifeDrive support
2010-07-22 15:03 ` [U-Boot] [PATCH 6/7] PXA: Add initial Palm LifeDrive support Marek Vasut
@ 2010-08-03 21:13 ` Wolfgang Denk
0 siblings, 0 replies; 10+ messages in thread
From: Wolfgang Denk @ 2010-08-03 21:13 UTC (permalink / raw)
To: u-boot
Dear Marek Vasut,
In message <1279811005-21858-6-git-send-email-marek.vasut@gmail.com> you wrote:
> Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
> ---
> board/palmld/Makefile | 54 ++++++++
> board/palmld/config.mk | 1 +
> board/palmld/lowlevel_init.S | 46 +++++++
> board/palmld/palmld.c | 81 ++++++++++++
> board/palmld/u-boot.lds | 56 +++++++++
> boards.cfg | 1 +
> include/configs/palmld.h | 275 ++++++++++++++++++++++++++++++++++++++++++
> 7 files changed, 514 insertions(+), 0 deletions(-)
> create mode 100644 board/palmld/Makefile
> create mode 100644 board/palmld/config.mk
> create mode 100644 board/palmld/lowlevel_init.S
> create mode 100644 board/palmld/palmld.c
> create mode 100644 board/palmld/u-boot.lds
> create mode 100644 include/configs/palmld.h
Entries to MAINTAINERS and MAKEALL missing.
> diff --git a/board/palmld/Makefile b/board/palmld/Makefile
> new file mode 100644
> index 0000000..c184cf6
> --- /dev/null
> +++ b/board/palmld/Makefile
> @@ -0,0 +1,54 @@
> +
> +#
Don't waste too many empty lines.
> +# Copyright (C) 2009
2009?
[Please see comments for previous patch; seems this one looks pretty
much similar.]
Actually the code looks pretty much similar, too.
Are you sure that multiple copies of htis code are needed?
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
We want to create puppets that pull their own strings. - Ann Marion
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 7/7] PXA: Vpac270 config fixes
2010-07-22 15:03 [U-Boot] [PATCH 1/7] ARM: Define __raw_readX and __raw_writeX Marek Vasut
` (4 preceding siblings ...)
2010-07-22 15:03 ` [U-Boot] [PATCH 6/7] PXA: Add initial Palm LifeDrive support Marek Vasut
@ 2010-07-22 15:03 ` Marek Vasut
2010-08-03 21:16 ` Wolfgang Denk
5 siblings, 1 reply; 10+ messages in thread
From: Marek Vasut @ 2010-07-22 15:03 UTC (permalink / raw)
To: u-boot
Define __io to get harddrive working.
Fix saving of environment into OneNAND.
Boot from harddrive when possible.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
include/configs/vpac270.h | 12 +++++++++++-
1 files changed, 11 insertions(+), 1 deletions(-)
diff --git a/include/configs/vpac270.h b/include/configs/vpac270.h
index 6d02995..a0383b2 100644
--- a/include/configs/vpac270.h
+++ b/include/configs/vpac270.h
@@ -36,7 +36,7 @@
/*
* Environment settings
*/
-#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
#define CONFIG_SYS_GBL_DATA_SIZE 128
@@ -49,6 +49,9 @@
"if usb reset && fatload usb 0 0xa4000000 uImage; then " \
"bootm 0xa4000000; " \
"fi; " \
+ "if ide reset && fatload ide 0 0xa4000000 uImage; then " \
+ "bootm 0xa4000000; " \
+ "fi; " \
"bootm 0x40000;"
#define CONFIG_BOOTARGS "console=tty0 console=ttyS0,115200"
#define CONFIG_TIMESTAMP
@@ -116,6 +119,7 @@
#define CONFIG_PXA_MMC
#define CONFIG_SYS_MMC_BASE 0xF0000000
#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
#define CONFIG_DOS_PARTITION
#endif
@@ -228,6 +232,12 @@
#undef CONFIG_IDE_LED
#undef CONFIG_IDE_RESET
+/*
+ * HACK WARNING: __io
+ * This MUST go away once the readb/writeb and inb/outb issue is solved
+ */
+#define __io
+
#define CONFIG_SYS_IDE_MAXBUS 1
#define CONFIG_SYS_IDE_MAXDEVICE 1
--
1.7.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [U-Boot] [PATCH 7/7] PXA: Vpac270 config fixes
2010-07-22 15:03 ` [U-Boot] [PATCH 7/7] PXA: Vpac270 config fixes Marek Vasut
@ 2010-08-03 21:16 ` Wolfgang Denk
0 siblings, 0 replies; 10+ messages in thread
From: Wolfgang Denk @ 2010-08-03 21:16 UTC (permalink / raw)
To: u-boot
Dear Marek Vasut,
In message <1279811005-21858-7-git-send-email-marek.vasut@gmail.com> you wrote:
> Define __io to get harddrive working.
> Fix saving of environment into OneNAND.
> Boot from harddrive when possible.
>
> Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
> ---
> include/configs/vpac270.h | 12 +++++++++++-
> 1 files changed, 11 insertions(+), 1 deletions(-)
>
> diff --git a/include/configs/vpac270.h b/include/configs/vpac270.h
> index 6d02995..a0383b2 100644
> --- a/include/configs/vpac270.h
> +++ b/include/configs/vpac270.h
> @@ -36,7 +36,7 @@
> /*
> * Environment settings
> */
> -#define CONFIG_ENV_SIZE 0x4000
> +#define CONFIG_ENV_SIZE 0x20000
Do you really need 128 KiB for environment data? [Note that this is
NOT a sector size or so!]
Really??? I think this is not true.
> +/*
> + * HACK WARNING: __io
> + * This MUST go away once the readb/writeb and inb/outb issue is solved
> + */
> +#define __io
Drop that.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Plan to throw one away. You will anyway."
- Fred Brooks, "The Mythical Man Month"
^ permalink raw reply [flat|nested] 10+ messages in thread