From: Marek Vasut <marek.vasut@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [IXP42x PATCH series v4 04/17] Fix IXP code to work after relocation was added
Date: Mon, 23 May 2011 02:38:34 +0200 [thread overview]
Message-ID: <201105230238.34947.marek.vasut@gmail.com> (raw)
In-Reply-To: <4DD960B7.6010407@discworld.dascon.de>
On Sunday, May 22, 2011 09:15:03 PM Michael Schwingen wrote:
> Am 05/21/2011 01:58 AM, schrieb Marek Vasut:
> >> -int timer_init (void)
> >> +unsigned long long get_ticks(void)
> >>
> >> {
> >>
> >> - /* install interrupt handler for timer */
> >> - irq_install_handler(IXP425_TIMER_2_IRQ, timer_isr, (void
> >> *)×tamp); -
> >> - /* setup the Timer counter value */
> >> - *IXP425_OSRT2 = (LATCH & ~IXP425_OST_RELOAD_MASK) | IXP425_OST_ENABLE;
> >> + ulong now = *IXP425_OSTS_B;
> >
> > Aren't you missing an IO accessor here ?
>
> Oops - you are correct.
>
> >> diff --git a/arch/arm/include/asm/arch-ixp/ixp425.h
> >> b/arch/arm/include/asm/arch-ixp/ixp425.h index 2114437..5132607 100644
> >> --- a/arch/arm/include/asm/arch-ixp/ixp425.h
> >> +++ b/arch/arm/include/asm/arch-ixp/ixp425.h
> >> @@ -391,9 +391,8 @@
> >>
> >> #define IXP425_TIMER_REG(x) (IXP425_TIMER_BASE_PHYS+(x))
> >> #endif
> >>
> >> -#if 0 /* test-only: also defined in npe/include/... */
> >> -#define IXP425_OSTS IXP425_TIMER_REG(IXP425_OSTS_OFFSET)
> >> -#endif
> >> +/* _B to avoid collision: also defined in npe/include/... */
> >> +#define IXP425_OSTS_B IXP425_TIMER_REG(IXP425_OSTS_OFFSET)
> >>
> >> #define IXP425_OST1 IXP425_TIMER_REG(IXP425_OST1_OFFSET)
> >> #define IXP425_OSRT1 IXP425_TIMER_REG(IXP425_OSRT1_OFFSET)
> >> #define IXP425_OST2 IXP425_TIMER_REG(IXP425_OST2_OFFSET)
> >
> > This will eventually enjoy being converted to struct ixp_timer_regset {
> > ... } goo. If you already did it in some further patch, sorry, I didn't
> > get there yet ;-)
>
> That would probably require a major rework of all the Intel access/NPE
> library code - this is not something I want to touch now.
> Most of these defines are used inside the Intel code, so cleaning up
> only outside of that area would not improve the code much.
It'd be cool to have this done in next cycle ;-)
>
> cu
> Michael
next prev parent reply other threads:[~2011-05-23 0:38 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-04-06 21:49 [U-Boot] [IXP42x PATCH series v4 00/17] Overview Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 01/17] add XScale sub architecture (IXP/PXA) to maintainer list Michael Schwingen
2011-05-20 23:53 ` Marek Vasut
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 02/17] add support for IXP42x Rev. B1 and newer Michael Schwingen
2011-05-20 23:53 ` Marek Vasut
2011-05-21 18:31 ` Wolfgang Denk
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 03/17] trigger hardware watchdog in IXP42x serial driver Michael Schwingen
2011-05-20 23:54 ` Marek Vasut
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 04/17] Fix IXP code to work after relocation was added Michael Schwingen
2011-05-20 23:58 ` Marek Vasut
2011-05-22 19:15 ` Michael Schwingen
2011-05-23 0:38 ` Marek Vasut [this message]
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 05/17] fix "depend" target in npe directory Michael Schwingen
2011-05-20 23:59 ` Marek Vasut
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 06/17] support CONFIG_SYS_LDSCRIPT on ARM Michael Schwingen
2011-05-22 15:33 ` Marek Vasut
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 07/17] use -ffunction-sections / --gc-sections on IXP42x Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 08/17] update/fix AcTux1 board Michael Schwingen
2011-05-21 0:03 ` Marek Vasut
2011-05-22 15:36 ` Marek Vasut
2011-05-22 21:53 ` Michael Schwingen
2011-05-22 19:51 ` Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 09/17] update/fix AcTux2 board Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 10/17] update/fix AcTux3 board Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 11/17] update/fix AcTux4 board Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 12/17] IXP NPE: add support for fixed-speed MII ports Michael Schwingen
2011-05-21 0:05 ` Marek Vasut
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 13/17] add dvlhost (dLAN 200 AV Wireless G) board Michael Schwingen
2011-05-21 0:06 ` Marek Vasut
2011-05-22 20:53 ` Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 14/17] update/fix IXDP425 / IXDPG425 boards Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 15/17] update/fix PDNB3 board Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 16/17] IXP42x PCI rewrite Michael Schwingen
2011-04-06 21:49 ` [U-Boot] [IXP42x PATCH series v4 17/17] run arm_pci_init after relocation Michael Schwingen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201105230238.34947.marek.vasut@gmail.com \
--to=marek.vasut@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox