[U-Boot] [PATCH 09/24] mxc_i2c: place imx_start code inline

[Marek Vasut <marex@denx.de>]

Dear Troy Kisky,

> imx_start is only referenced once so
> move to that location.
> 
> Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Acked-by: Marek Vasut <marex@denx.de>

> ---
>  drivers/i2c/mxc_i2c.c |   53
> +++++++++++++++++++------------------------------ 1 file changed, 20
> insertions(+), 33 deletions(-)
> 
> diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
> index 9063d1e..ac91872 100644
> --- a/drivers/i2c/mxc_i2c.c
> +++ b/drivers/i2c/mxc_i2c.c
> @@ -199,37 +199,6 @@ static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8
> byte) }
> 
>  /*
> - * Start the controller
> - */
> -int i2c_imx_start(void)
> -{
> -	struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)I2C_BASE;
> -	unsigned int temp = 0;
> -	int result;
> -
> -	/* Enable I2C controller */
> -	writeb(0, &i2c_regs->i2sr);
> -	writeb(I2CR_IEN, &i2c_regs->i2cr);
> -
> -	/* Wait controller to be stable */
> -	udelay(50);
> -
> -	/* Start I2C transaction */
> -	temp = readb(&i2c_regs->i2cr);
> -	temp |= I2CR_MSTA;
> -	writeb(temp, &i2c_regs->i2cr);
> -
> -	result = wait_for_sr_state(i2c_regs, ST_BUS_BUSY);
> -	if (result < 0)
> -		return result;
> -
> -	temp |= I2CR_MTX | I2CR_TX_NO_AK;
> -	writeb(temp, &i2c_regs->i2cr);
> -
> -	return 0;
> -}
> -
> -/*
>   * Stop the controller
>   */
>  void i2c_imx_stop(void)
> @@ -255,10 +224,28 @@ void i2c_imx_stop(void)
>  static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs,
>  		uchar chip, uint addr, int alen)
>  {
> -	int ret = i2c_imx_start();
> -	if (ret)
> +	unsigned int temp;
> +	int ret;
> +
> +	/* Enable I2C controller */
> +	writeb(0, &i2c_regs->i2sr);
> +	writeb(I2CR_IEN, &i2c_regs->i2cr);
> +
> +	/* Wait for controller to be stable */
> +	udelay(50);
> +
> +	/* Start I2C transaction */
> +	temp = readb(&i2c_regs->i2cr);
> +	temp |= I2CR_MSTA;
> +	writeb(temp, &i2c_regs->i2cr);
> +
> +	ret = wait_for_sr_state(i2c_regs, ST_BUS_BUSY);
> +	if (ret < 0)
>  		goto exit;
> 
> +	temp |= I2CR_MTX | I2CR_TX_NO_AK;
> +	writeb(temp, &i2c_regs->i2cr);
> +
>  	/* write slave address */
>  	ret = tx_byte(i2c_regs, chip << 1);
>  	if (ret < 0)

Best regards,
Marek Vasut