From mboxrd@z Thu Jan  1 00:00:00 1970
From: Albert ARIBAUD <albert.u.boot@aribaud.net>
Date: Thu, 5 Jul 2012 13:45:43 +0200
Subject: [U-Boot] USB detection
In-Reply-To: <1341484069.3616.14.camel@Manukumar>
References: <1337677828.2382.30.camel@Manukumar>
	<201205221615.07965.marex@denx.de> <4FBBD34F.5010501@freescale.com>
	<1337752596.2378.37.camel@Manukumar>
	<20120523080211.B633820025A@gemini.denx.de>
	<1337761847.2378.71.camel@Manukumar>
	<4FBD0D43.1060208@freescale.com>
	<1338354171.2370.13.camel@Manukumar>
	<4FC64859.2070609@freescale.com>
	<1338437711.2367.9.camel@Manukumar>
	<4FC79A7F.8050003@freescale.com>
	<1338545434.2370.11.camel@Manukumar>
	<4FC8F89F.5080005@freescale.com>
	<1341484069.3616.14.camel@Manukumar>
Message-ID: <20120705134543.134da313@aari01-12>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Hi Manukumar,

On Thu, 05 Jul 2012 15:57:49 +0530, Manukumar
<manukumar@signal-networks.com> wrote:
> Hello,
> 
> I have connected USB hard disk to P1020RB 

Which board is this? Neither "git grep -i P1020RB" nor "find . iname
'*P1020RB*'" yield any result.

> and in command prompt(u-boot) i used
> command
> => usb start
> (Re)start USB...
> USB:   Register 10011 NbrPorts 1
> USB EHCI 1.00
> scanning bus for devices... 3 USB Device(s) found
>        scanning bus for storage devices... 1 Storage Device(s) found
> 
> => usb dev
> 
> USB device 0: Vendor: Seagate  Rev: 0130 Prod: Portable
>             Type: Hard Disk
>             Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
> 
> and USB got detected.
> 
> but If i used the same command in our custom board
> => usb start
> (Re)start USB...
> USB:   Register 10011 NbrPorts 1
> USB EHCI 1.00
> scanning bus for devices... 1 USB Device(s) found
>        scanning bus for storage devices... 0 Storage Device(s) found
> 
> => usb dev
> 
> USB device -1: device type unknown
> 
> 
> How do resolve this issue and why the device is not detecting my USB
> hard disk.?

Considering that you're trying this on a custom board, and assuming
"P1020RB" is a nickname for a board supported in mainline U-Boot, there
are two possibilities:

1) the custom board uses exactly the same U-Boot (source, configuration
and binaries) as P1020RB, and the issue is in HW, in which case we can
barely help;

2) the custom board uses a custom U-Boot, and we can barely help too,
as this issue is not about (recent) mainline U-Boot code.

> manukumar
> signal-networks

Amicalement,
-- 
Albert.