From mboxrd@z Thu Jan  1 00:00:00 1970
From: Marek Vasut <marex@denx.de>
Date: Fri, 6 Jul 2012 20:39:32 +0200
Subject: [U-Boot] [PATCH V2 01/25] mxc_i2c: fix i2c_imx_stop
In-Reply-To: <4FF72B21.6000607@boundarydevices.com>
References: <1341518043-26191-1-git-send-email-troy.kisky@boundarydevices.com>
	<201207061946.26627.marex@denx.de>
	<4FF72B21.6000607@boundarydevices.com>
Message-ID: <201207062039.32950.marex@denx.de>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Dear Troy Kisky,

> On 7/6/2012 10:46 AM, Marek Vasut wrote:
> > Dear Troy Kisky,
> > 
> >> On 7/5/2012 11:50 PM, Marek Vasut wrote:
> >>> Dear Troy Kisky,
> >>> 
> >>>> On 7/5/2012 12:53 PM, Troy Kisky wrote:
> >>>>> Instead of clearing 2 bits, all the other
> >>>>> bits were set because '|=' was used instead
> >>>>> of '&='.
> >>>>> 
> >>>>> Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
> >>>>> Acked-by: Marek Vasut <marex@denx.de>
> >>>>> Acked-by: Stefano Babic <sbabic@denx.de>
> >>>>> 
> >>>>> ---
> >>>>> V2: add acks
> >>>>> ---
> >>>>> 
> >>>>>     drivers/i2c/mxc_i2c.c |    2 +-
> >>>>>     1 file changed, 1 insertion(+), 1 deletion(-)
> >>>>> 
> >>>>> diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
> >>>>> index fc68062..c0c45fd 100644
> >>>>> --- a/drivers/i2c/mxc_i2c.c
> >>>>> +++ b/drivers/i2c/mxc_i2c.c
> >>>>> @@ -264,7 +264,7 @@ void i2c_imx_stop(void)
> >>>>> 
> >>>>>     	/* Stop I2C transaction */
> >>>>>     	temp = readb(&i2c_regs->i2cr);
> >>>>> 
> >>>>> -	temp |= ~(I2CR_MSTA | I2CR_MTX);
> >>>>> +	temp &= ~(I2CR_MSTA | I2CR_MTX);
> >>>>> 
> >>>>>     	writeb(temp, &i2c_regs->i2cr);
> >>>>>     	
> >>>>>     	i2c_imx_bus_busy(0);
> >>>> 
> >>>> This series was tested on a sabrelite and a i.mx51 board
> >>> 
> >>> Sigh, I should test it on the efikamx board. It has some i2c chip
> >>> that's hard to talk to since it's quite sensitive to the behavior of
> >>> the bus. But since I'm dead busy now, I'll just trust you. I'm glad
> >>> you found it, Troy :)
> >> 
> >> I'd rather have your verification than trust :-)
> >> Thanks for the reviews.
> > 
> > Hmm, lemme see.
> > 
> >> Troy
> > 
> > Best regards,
> > Marek Vasut
> 
> Here's a patch to enable i2c for efikamx....

It should be enabled already ... hm, I think I'll have to dig deeper.

> 
> Troy

Best regards,
Marek Vasut