[U-Boot] [PATCH 6/6] net: asix: add AX88772B support

[Marek Vasut <marek.vasut@gmail.com>]

Dear Lucas Stach,

> Add AX88772B ID together with two fixes needed to make this work.
> 
> 1. The packet length check has to be adjusted, as all ASIX chips
> only use 11 bits to indicate the length. AX88772B uses the other
> bits to indicate unrelated things, which cause the check to fail.
> This fix is based on a fix for the Linux kernel by Marek Vasut.
> Linux upstream commit: bca0beb9363f8487ac902931a50eb00180a2d14a
> 
> 2. AX88772B provides several bulk endpoints. Only the first
> IN/OUT endpoints work in the default configuration. So stop
> enumeration after we found them to avoid overwriting the
> endpoint config with a non-working one.
> 
> Signed-off-by: Lucas Stach <dev@lynxeye.de>

Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>

> ---
>  drivers/usb/eth/asix.c | 30 +++++++++++++++++++-----------
>  1 Datei ge?ndert, 19 Zeilen hinzugef?gt(+), 11 Zeilen entfernt(-)
> 
> diff --git a/drivers/usb/eth/asix.c b/drivers/usb/eth/asix.c
> index 6ab3e82..79246d8 100644
> --- a/drivers/usb/eth/asix.c
> +++ b/drivers/usb/eth/asix.c
> @@ -543,13 +543,13 @@ static int asix_recv(struct eth_device *eth)
>  		}
>  		memcpy(&packet_len, buf_ptr, sizeof(packet_len));
>  		le32_to_cpus(&packet_len);
> -		if (((packet_len >> 16) ^ 0xffff) != (packet_len & 0xffff)) {
> +		if (((~packet_len >> 16) & 0x7ff) != (packet_len & 0x7ff)) {
>  			debug("Rx: malformed packet length: %#x (%#x:%#x)\n",
> -			      packet_len, (packet_len >> 16) ^ 0xffff,
> -			      packet_len & 0xffff);
> +			      packet_len, (~packet_len >> 16) & 0x7ff,
> +			      packet_len & 0x7ff);
>  			return -1;
>  		}
> -		packet_len = packet_len & 0xffff;
> +		packet_len = packet_len & 0x7ff;
>  		if (packet_len > actual_len - sizeof(packet_len)) {
>  			debug("Rx: too large packet: %d\n", packet_len);
>  			return -1;
> @@ -597,6 +597,7 @@ static const struct asix_dongle asix_dongles[] = {
>  	{ 0x13b1, 0x0018, FLAG_TYPE_AX88172 },	/* Linksys 200M v2.1 */
>  	{ 0x1557, 0x7720, FLAG_TYPE_AX88772 },	/* 0Q0 cable ethernet */
>  	{ 0x2001, 0x3c05, FLAG_TYPE_AX88772 },	/* DLink DUB-E100 H/W Ver B1
> Alternate */ +	{ 0x0b95, 0x772b, FLAG_TYPE_AX88772B | FLAG_EEPROM_MAC 
},
> /* ASIX 88772B */ { 0x0000, 0x0000, FLAG_NONE }	/* END - Do not remove 
*/
>  };
> 
> @@ -606,6 +607,7 @@ int asix_eth_probe(struct usb_device *dev, unsigned int
> ifnum, {
>  	struct usb_interface *iface;
>  	struct usb_interface_descriptor *iface_desc;
> +	int ep_in_found = 0, ep_out_found = 0;
>  	int i;
> 
>  	/* let's examine the device now */
> @@ -649,13 +651,19 @@ int asix_eth_probe(struct usb_device *dev, unsigned
> int ifnum, /* is it an BULK endpoint? */
>  		if ((iface->ep_desc[i].bmAttributes &
>  		     USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_BULK) {
> -			if (iface->ep_desc[i].bEndpointAddress & USB_DIR_IN)
> -				ss->ep_in = iface->ep_desc[i].bEndpointAddress &
> -					USB_ENDPOINT_NUMBER_MASK;
> -			else
> -				ss->ep_out =
> -					iface->ep_desc[i].bEndpointAddress &
> -					USB_ENDPOINT_NUMBER_MASK;
> +			if (iface->ep_desc[i].bEndpointAddress & USB_DIR_IN) {
> +				if (!ep_in_found) {
> +					ss->ep_in = iface-
>ep_desc[i].bEndpointAddress &
> +					            USB_ENDPOINT_NUMBER_MASK;
> +					ep_in_found = 1;
> +				}
> +			} else {
> +				if (!ep_out_found) {
> +					ss->ep_out = iface-
>ep_desc[i].bEndpointAddress &
> +					             USB_ENDPOINT_NUMBER_MASK;
> +					ep_out_found = 1;
> +				}
> +			}
>  		}
> 
>  		/* is it an interrupt endpoint? */

Best regards,
Marek Vasut