From mboxrd@z Thu Jan  1 00:00:00 1970
From: Marek Vasut <marex@denx.de>
Date: Sat, 22 Sep 2012 20:00:30 +0200
Subject: [U-Boot] [PATCH 1/6] h2200: Add support for iPAQ h2200
In-Reply-To: <505DF25D.8010200@gmail.com>
References: <1348083538-16123-1-git-send-email-luk0104@gmail.com>
	<201209221904.37848.marex@denx.de> <505DF25D.8010200@gmail.com>
Message-ID: <201209222000.30366.marex@denx.de>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Dear ?ukasz Da?ek,

> On 22.09.2012 19:04, Marek Vasut wrote:
> > Dear ?ukasz Da?ek,
> > 
> >> On 19.09.2012 23:02, Marek Vasut wrote:
> >>>> and at the offset
> >>>> + * 0x40 ascii characters 'ECEC', secondly 1st stage
> >>>> + * loads code from flash into SDRAM at address 0xa0040000
> >>>> + * so all instructions which reinitializes memory
> >>>> + * controller have to be disabled.
> >>>> + */
> >>>> +
> >>>> +static inline void writelrb(uint32_t val, uint32_t addr)
> >>> 
> >>> Replace this with clrsetbits_le32()
> >> 
> >> I've copied writelrb and pxa2xx_dram_init from pxa2xx.c
> >> and I think there is a reason why it's done that way and not by
> >> clrsetbits_le32. But if you insist I can replace all calls to writelrb
> >> by clrsetbits.
> > 
> > And can you elaborate on the reason please?
> > 
> > (hint: clrsetbits() wasn't there by the time)
> 
> I don't know what was the reason. I didn't change becuse I didn't
> want to break it.

If you have time, replace it with clrsetbits() please ... in the original file.

> >>>> +{
> >>>> +	writel(val, addr);
> >>>> +	asm volatile("" : : : "memory");
> >>>> +	readl(addr);
> >>>> +	asm volatile("" : : : "memory");
> >>>> +}
> >>>> +
> >>>> +static void h2200_pxa2xx_dram_init(void)
> >>> 
> >>> Why do you duplicate it ?!
> >>> 
> >>> [...]
> >> 
> >> Because code in pxa2xx.c disable and then re-enable memory.
> >> And u-boot is executed from memory (1st stage bootloder
> >> copied it there).
> > 
> > So don't reinit the memory at all, just skip this whole part.
> 
> 1st stage loader doesn't init everything (for example MSC).

So I checked ... every board calls the dram init on it's own in dram_init() ... 
so just don't do that.

> >>> +
> >>> +# define CONFIG_USB_ETHER		1
> >>> +# define CONFIG_USBNET_DEV_ADDR		"de:ad:be:ef:00:01"
> >>> +# define CONFIG_USBNET_HOST_ADDR	"de:ad:be:ef:00:02"
> >>> Definitelly not, any mac address setting should not be present, Joe ?
> >> 
> >> So tell me how should I specify mac addresses? By EXTRA_ENV_SETTINGS?
> > 
> > Joe explained it, your adapter doesn't carry it's own mac?
> 
> No.

Then leave it in ?

> ?ukasz Da?ek

Best regards,
Marek Vasut