[U-Boot] SMSC LAN9514 on TI DM37x board

From: Marek Vasut <marex@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] SMSC LAN9514 on TI DM37x board
Date: Mon, 5 Nov 2012 23:57:40 +0100	[thread overview]
Message-ID: <201211052357.40830.marex@denx.de> (raw)
In-Reply-To: <50977002.5080008@embedded-sol.com>

Dear Felix Radensky,

> Hi Marek,
> 
> Can you please take a look at this problem.

Can you please avoid top-posting? Does U-Boot even support your USB device?

> Thanks a lot.
> 
> Felix.
> 
> On 11/02/2012 08:38 AM, Felix Radensky wrote:
> > Hi,
> > 
> > I'm running u-boot-2012.10 on a custom DM37x based board.
> > The board has LAN9514 USB Ethernet adapter connected
> > in EHCI host controller via USB3320 ULPI PHY. This is very
> > similar to BeagleBoard XM. Both Ethernet and USB hub work
> > in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however,
> > neither Ethernet nor mass storage devices attached to hub
> > are not detected.
> > 
> > Below is boot log:
> > 
> > U-Boot 2012.10 (Nov 02 2012 - 00:44:41)
> > 
> > OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
> > Pro4Tech MVC404 board + LPDDR/NAND
> > I2C:   ready
> > DRAM:  256 MiB
> > NAND:  512 MiB
> > MMC:   OMAP SD/MMC: 0
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   Net Initialization Skipped
> > No ethernet found.
> > Hit any key to stop autoboot:  0
> > MVC404 > usb start
> > (Re)start USB...
> > USB:   Register 1313 NbrPorts 3
> > USB EHCI 1.00
> > scanning bus for devices... 1 USB Device(s) found
> > 
> >        scanning bus for storage devices... 0 Storage Device(s) found
> >        scanning bus for ethernet devices... 0 Ethernet Device(s) found
> > 
> > MVC404 > usb info
> > 1: Hub,  USB Revision 2.0
> > 
> >  - u-boot EHCI Host Controller
> >  - Class: Hub
> >  - PacketSize: 64  Configurations: 1
> >  - Vendor: 0x0000  Product 0x0000 Version 1.0
> >  
> >    Configuration: 1
> >    - Interfaces: 1 Self Powered 0mA
> >    
> >      Interface: 0
> >      - Alternate Setting 0, Endpoints: 1
> >      - Class Hub
> >      - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms
> > 
> > I have the following definitions in the code:
> > 
> > #define CONFIG_USB_OMAP3
> > #define CONFIG_USB_EHCI
> > #define CONFIG_USB_EHCI_OMAP
> > #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS    3
> > #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO    24
> > #define CONFIG_USB_ULPI
> > #define CONFIG_USB_ULPI_VIEWPORT_OMAP
> > #define CONFIG_USB_STORAGE
> > 
> > static struct omap_usbhs_board_data usbhs_bdata = {
> > 
> >     .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
> >     .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
> >     .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
> > 
> > };
> > 
> > MUX_VAL(CP(ETK_D15_ES2),    (IDIS | PTD | DIS | M4)) /*GPIO_24*/
> > 
> > I'd appreciate any help in fixing the problem.
> > 
> > Thanks.
> > 
> > Felix Radensky.
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot