[U-Boot] [PATCH 8/8] board support for palm treo 680

Mike Dunn
2013-04-07T16:41:05Z

A quick overview of u-boot implementation on the treo 680...

The treo 680 has a Diskonchip G4 nand flash chip. This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device. The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL). At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it. The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used. To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image. That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.

The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward. I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).

Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen. But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
---
CREDITS | 4 +
MAINTAINERS | 3 +
board/palmtreo680/Makefile | 47 +++
board/palmtreo680/flash_u-boot.c | 170 ++++++++++
board/palmtreo680/palmtreo680.c | 184 +++++++++++
board/palmtreo680/palmtreo680_spl.lds | 69 ++++
boards.cfg | 1 +
doc/README.palmtreo680 | 570 +++++++++++++++++++++++++++++++++
include/configs/palmtreo680.h | 307 ++++++++++++++++++
9 files changed, 1355 insertions(+), 0 deletions(-)
create mode 100644 board/palmtreo680/Makefile
create mode 100644 board/palmtreo680/flash_u-boot.c
create mode 100644 board/palmtreo680/palmtreo680.c
create mode 100644 board/palmtreo680/palmtreo680_spl.lds
create mode 100644 doc/README.palmtreo680
create mode 100644 include/configs/palmtreo680.h

diff --git a/CREDITS b/CREDITS
index 7c1458f..3b657e9 100644
--- a/CREDITS
+++ b/CREDITS
@@ -124,6 +124,10 @@ N: James F. Dougherty
E: jfd at GigabitNetworks.COM
D: Port to the MOUSSE board

+N: Mike Dunn
+E: mikedunn at newsguy.com
+D: Palmtreo680 board, docg4 nand flash driver
+
N: Dave Ellis
E: DGE at sixnetio.com
D: EEPROM Speedup, SXNI855T port
diff --git a/MAINTAINERS b/MAINTAINERS
index 1614b91..db62af1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -650,6 +650,9 @@ Wolfgang Denk <wd@denx.de>
imx27lite i.MX27
qong i.MX31

+Mike Dunn <mikedunn@newsguy.com>
+ palmtreo680 pxa270
+
Kristoffer Ericson <kristoffer.ericson@gmail.com>

jornada SA1110
diff --git a/board/palmtreo680/Makefile b/board/palmtreo680/Makefile
new file mode 100644
index 0000000..e729e6a
--- /dev/null
+++ b/board/palmtreo680/Makefile
@@ -0,0 +1,47 @@
+#
+# Palm Treo680 Support
+#
+# Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := palmtreo680.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/palmtreo680/flash_u-boot.c b/board/palmtreo680/flash_u-boot.c
new file mode 100644
index 0000000..ee4213e
--- /dev/null
+++ b/board/palmtreo680/flash_u-boot.c
@@ -0,0 +1,170 @@
+/*
+ * This file is not part of u-boot. It is a userspace Linux utility that, when
+ * run on the Treo 680, will program u-boot to flash. The docg4 driver *must*
+ * be loaded with the reliable_mode and ignore_badblocks parameters enabled:
+ *
+ * modprobe docg4 ignore_badblocks=1 reliable_mode=1
+ *
+ * This utility writes the concatenated spl + u-boot image to the start of the
+ * mtd device in the format expected by the IPL/SPL. The image file and mtd
+ * device node are passed to the utility as arguments.
+ *
+ * When you compile this, note that it links to libmtd from mtd-utils, so ensure
+ * that your include and lib paths include this.
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <sys/stat.h>
+#include <fcntl.h>
+#include <string.h>
+#include <sys/types.h>
+#include <unistd.h>
+#include <errno.h>
+#include <mtd/mtd-user.h>
+#include "libmtd.h"
+
+#define RELIABLE_BLOCKSIZE 0x10000 /* block capacity in reliable mode */
+#define STANDARD_BLOCKSIZE 0x40000 /* block capacity in normal mode */
+#define PAGESIZE 512
+#define PAGES_PER_BLOCK 512
+#define OOBSIZE 7 /* available to user (16 total) */
+
+uint8_t ff_oob[OOBSIZE] = {0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff};
+
+/* this is the magic number the IPL looks for (ASCII "BIPO") */
+uint8_t page0_oob[OOBSIZE] = {'B', 'I', 'P', 'O', 0xff, 0xff, 0xff};
+
+int main(int argc, char * const argv[])
+{
+ int devfd, datafd, num_blocks, block;
+ off_t file_size;
+ libmtd_t mtd_desc;
+ struct mtd_dev_info devinfo;
+ uint8_t *blockbuf;
+ char response[8];
+
+ if (argc != 3) {
+ printf("usage: %s <image file> \n", argv[0]);
+ exit(-1);
+ }
+
+ mtd_desc = libmtd_open();
+ if (mtd_desc == NULL) {
+ fprintf(stderr, "can't initialize libmtd\n");
+ exit(-1);
+ }
+
+ /* open the spl image file and mtd device */
+ datafd = open(argv[1], O_RDONLY);
+ if (datafd == -1) {
+ perror(argv[1]);
+ exit(-1);
+ }
+ devfd = open(argv[2], O_WRONLY);
+ if (devfd == -1) {
+ perror(argv[2]);
+ exit(-1);
+ }
+ if (mtd_get_dev_info(mtd_desc, argv[2], &devinfo) < 0) {
+ fprintf(stderr, "mtd_get_dev_info failed\n");
+ exit(-1);
+ }
+
+ /* determine the number of blocks needed by the image */
+ file_size = lseek(datafd, 0, SEEK_END);
+ if (file_size == (off_t)-1) {
+ perror("lseek");
+ exit(-1);
+ }
+ num_blocks = (file_size + RELIABLE_BLOCKSIZE - 1) / RELIABLE_BLOCKSIZE;
+ file_size = lseek(datafd, 0, SEEK_SET);
+ if (file_size == (off_t)-1) {
+ perror("lseek");
+ exit(-1);
+ }
+ printf("The mtd partition contains %d blocks\n", devinfo.eb_cnt);
+ printf("U-boot will occupy %d blocks\n", num_blocks);
+ if (num_blocks > devinfo.eb_cnt) {
+ fprintf(stderr, "Insufficient blocks on partition\n");
+ exit(-1);
+ }
+
+ printf("Do you want to proceed?\n");
+ scanf("%s", response);
+ if ((response[0] != 'y') && (response[0] != 'Y')) {
+ printf("Exiting\n");
+ close(devfd);
+ close(datafd);
+ exit(-1);
+ }
+
+ blockbuf = malloc(RELIABLE_BLOCKSIZE);
+ if (blockbuf == NULL) {
+ perror("malloc");
+ exit(-1);
+ }
+
+ for (block = 0; block < num_blocks; block++) {
+ int ofs, page;
+ ssize_t read_ret;
+ uint8_t *pagebuf = blockbuf, *buf = blockbuf;
+ uint8_t *oobbuf = page0_oob; /* magic num in oob of 1st page */
+ size_t len = RELIABLE_BLOCKSIZE;
+ int ret;
+
+#if 0 /* to minimize risk, require the user to erase the partition beforehand */
+ printf("Block %d: erasing\r", block + 1);
+ ret = mtd_erase(mtd_desc, &devinfo, devfd, block);
+ if (ret) {
+ fprintf(stderr,
+ "\nmtd_erase on block %d returned %d\n",
+ block + 1, ret);
+ exit(-1);
+ }
+#endif
+
+ /* read data for one block from file */
+ while (len != 0 && (read_ret = read(datafd, buf, len)) != 0) {
+ if (read_ret == -1) {
+ if (errno == EINTR)
+ continue;
+ perror("read");
+ exit(-1);
+ }
+ len -= read_ret;
+ buf += read_ret;
+ }
+
+ printf("Block %d: writing\r", block + 1);
+ fflush(stdout);
+
+ for (page = 0, ofs = 0;
+ page < PAGES_PER_BLOCK;
+ page++, ofs += PAGESIZE) {
+ if (page & 0x04) /* Odd-numbered 2k page */
+ continue; /* skipped in reliable mode */
+
+ ret = mtd_write(mtd_desc, &devinfo, devfd, block, ofs,
+ pagebuf, PAGESIZE, oobbuf, OOBSIZE,
+ MTD_OPS_PLACE_OOB);
+ if (ret) {
+ fprintf(stderr,
+ "\nmtd_write returned %d on block %d, ofs %x\n",
+ ret, block + 1, ofs);
+ exit(-1);
+ }
+ oobbuf = ff_oob; /* oob for subsequent pages */
+
+ if (page & 0x01) /* odd-numbered subpage */
+ pagebuf += PAGESIZE;
+ }
+ }
+
+ printf("\nDone\n");
+
+ close(devfd);
+ close(datafd);
+ free(blockbuf);
+ return 0;
+}
diff --git a/board/palmtreo680/palmtreo680.c b/board/palmtreo680/palmtreo680.c
new file mode 100644
index 0000000..957d4a9
--- /dev/null
+++ b/board/palmtreo680/palmtreo680.c
@@ -0,0 +1,184 @@
+/*
+ * Palm Treo 680 Support
+ *
+ * Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <serial.h>
+#include <nand.h>
+#include <malloc.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch-pxa/pxa.h>
+#include <asm/arch-pxa/regs-mmc.h>
+#include <asm/io.h>
+#include <asm/global_data.h>
+#include <u-boot/crc.h>
+#include <linux/mtd/docg4.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct nand_chip docg4_nand_chip;
+
+int board_init(void)
+{
+ /* We have RAM, disable cache */
+ dcache_disable();
+ icache_disable();
+
+ gd->bd->bi_arch_number = MACH_TYPE_TREO680;
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ /* IPL initializes SDRAM (we're already running from it) */
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
+ return 0;
+}
+
+#ifdef CONFIG_LCD
+void lcd_enable(void)
+{
+ /* power-up and enable the lcd */
+ writel(0x00400000, GPSR(86)); /* enable; drive high */
+ writel(0x00002000, GPSR(77)); /* power; drive high */
+ writel(0x02000000, GPCR(25)); /* enable_n; drive low */
+
+ /* turn on LCD backlight */
+ writel(0x00, PWM_CTRL0); /* set PWM for reasonable brightness */
+ writel(0x1b1, PWM_PERVAL0);
+ writel(0xfd, PWM_PWDUTY0);
+ writel(0x00000040, GPSR(38)); /* backlight power on */
+}
+#endif
+
+#ifdef CONFIG_MMC
+int board_mmc_init(bd_t *bis)
+{
+ writel(0x00000400, GPSR(42)); /* power on */
+ return pxa_mmc_register(0);
+}
+#endif
+
+void board_nand_init(void)
+{
+ /* we have one 128M diskonchip G4 */
+
+ struct mtd_info *mtd = &nand_info[0];
+ struct nand_chip *nand = &docg4_nand_chip;
+ if (docg4_nand_init(mtd, nand, 0))
+ hang();
+}
+
+#ifdef CONFIG_SPL_BUILD
+void *memcpy(void *dest, const void *src, size_t count)
+{
+ unsigned long *dl = (unsigned long *)dest, *sl = (unsigned long *)src;
+ char *d8, *s8;
+
+ if (src == dest)
+ return dest;
+
+ /* while all data is aligned (common case), copy a word at a time */
+ if ((((ulong)dest | (ulong)src) & (sizeof(*dl) - 1)) == 0) {
+ while (count >= sizeof(*dl)) {
+ *dl++ = *sl++;
+ count -= sizeof(*dl);
+ }
+ }
+ /* copy the reset one byte at a time */
+ d8 = (char *)dl;
+ s8 = (char *)sl;
+ while (count--)
+ *d8++ = *s8++;
+
+ return dest;
+}
+
+
+void nand_boot(void)
+{
+ __attribute__((noreturn)) void (*uboot)(void);
+
+ extern const void *_start, *_end; /* boundaries of spl in memory */
+
+ /* size of spl; ipl loads this, and then a portion of u-boot */
+ const size_t spl_image_size = ((size_t)&_end - (size_t)&_start);
+
+ /* the flash offset of the blocks that are loaded by the spl */
+ const uint32_t spl_load_offset = CONFIG_SYS_NAND_U_BOOT_OFFS +
+ DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_SIZE;
+
+ /* total number of bytes loaded by IPL */
+ const size_t ipl_load_size =
+ DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_CAPACITY_SPL;
+
+ /* number of bytes of u-boot proper that was loaded by the IPL */
+ const size_t ipl_uboot_load_size = ipl_load_size - spl_image_size;
+
+ /* number of remaining bytes of u-boot that the SPL must load */
+ const size_t spl_load_size =
+ CONFIG_SYS_NAND_U_BOOT_SIZE - ipl_load_size;
+
+ /* memory address where we resume loading u-boot */
+ void *const load_addr =
+ (void *)(CONFIG_SYS_NAND_U_BOOT_DST + ipl_uboot_load_size);
+
+ /*
+ * Copy the portion of u-boot already read from flash by the IPL to its
+ * correct load address.
+ */
+ memcpy((void *)CONFIG_SYS_NAND_U_BOOT_DST, &_end, ipl_uboot_load_size);
+
+ /*
+ * Resume loading u-boot where the IPL left off.
+ */
+ nand_spl_load_image(spl_load_offset, spl_load_size, load_addr);
+
+#ifdef CONFIG_NAND_ENV_DST
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (void *)CONFIG_NAND_ENV_DST);
+
+#ifdef CONFIG_ENV_OFFSET_REDUND
+ nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE,
+ (void *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE);
+#endif
+#endif
+ /*
+ * Jump to U-Boot image
+ */
+ uboot = (void *)CONFIG_SYS_NAND_U_BOOT_START;
+ (*uboot)();
+}
+
+void board_init_f(ulong bootflag)
+{
+ nand_boot();
+}
+
+void hang(void)
+{
+ for (;;) {
+ }
+}
+
+#endif /* CONFIG_SPL_BUILD */
diff --git a/board/palmtreo680/palmtreo680_spl.lds b/board/palmtreo680/palmtreo680_spl.lds
new file mode 100644
index 0000000..bdfa2aa
--- /dev/null
+++ b/board/palmtreo680/palmtreo680_spl.lds
@@ -0,0 +1,69 @@
+/*
+ * Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/*
+ * This file is a slight modification to the default pxa link script. The '*'
+ * wildcard is added to the section names to consolidate all the sections
+ * created by the -ffunction-sections and -fdata-sections compiler flags.
+ */
+
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ arch/arm/cpu/pxa/start.o (.text)
+ *(.text*)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : {
+ *(.data*)
+ }
+
+ . = ALIGN(4);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ _end = .;
+
+ /* internal SRAM is used for the SPL's bss */
+ .bss 0x5c000000 : {
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end = .;
+ }
+}
diff --git a/boards.cfg b/boards.cfg
index 5fc70be..72a9440 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -331,6 +331,7 @@ h2200 arm pxa
lubbock arm pxa
palmld arm pxa
palmtc arm pxa
+palmtreo680 arm pxa
polaris arm pxa trizepsiv - - trizepsiv:POLARIS
pxa255_idp arm pxa
trizepsiv arm pxa
diff --git a/doc/README.palmtreo680 b/doc/README.palmtreo680
new file mode 100644
index 0000000..15c09dd
--- /dev/null
+++ b/doc/README.palmtreo680
@@ -0,0 +1,570 @@
+
+README for the Palm Treo 680.
+
+Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
+
+You may reproduce the contents of this file entirely or in part, but please
+credit me by name if you do. Thanks.
+
+
+Intro
+=====
+
+Yes, you can program u-boot onto the flash of your Palm Treo 680 so that u-boot
+(then Linux, Android, ...) runs at power-up. This document describes how, and
+gives some implementation details on this port of u-boot.
+
+But first, I probably don't need to tell you that after doing this, your phone
+will no longer run PalmOS. You *may* be able to later restore your phone to its
+original state by creating a backup image of the flash before writing u-boot
+(details below), but this is not heavily tested and should not be relied upon.
+There is also the possibility that something may go wrong during the process of
+programming u-boot, leaving you with a bricked phone. If you follow these
+instructions carefully this chance will be minimized, but I do not recommend
+that you program u-boot onto a phone that you can not afford to lose, and
+certainly not one that contains important data that is not backed up elsewhere.
+I AM NOT RESPONSIBLE FOR THE LOSS OF YOUR PHONE. DO THIS AT YOUR OWN RISK.
+Having said that, feel free to send me a note cursing me out if something does
+go wrong, but please tell me what happened exactly. For that matter, I'd love
+to hear from you if you succeed.
+
+To program u-boot to your flash, you will need to boot the Linux kernel on your
+phone using a PalmOS bootloader such as cocoboot. The details of building and
+running Linux on your Treo (cross-compiling, creating a root filesystem,
+configuring the kernel, etc) are beyond the scope of this document.
+
+
+
+Hardware Prerequisites
+======================
+
+A Palm Treo 680:
+ (dugh)
+
+A Palm usb cable:
+ You'll need this to establish a usbtty console connection to u-boot from a
+ desktop PC. Currently there is no support in u-boot for the pxa27x keypad
+ (coming soon), so a serial link must be used for the console.
+ These cables are still widely available if you don't already have one.
+
+A Linux desktop PC.
+ You may be able to use Windows for the u-boot console if you have a usb driver
+ that is compatible with the Linux usbserial driver, but for programming u-boot
+ to flash, you'll really want to use a Linux PC.
+
+
+
+Treo-side Software Prerequisites
+================================
+
+Linux bootloader for PalmOS:
+
+ Cocoboot is the only one I'm aware of. If you don't already have this, you
+ can download it from
+ https://download.enlightenment.org/misc/Illume/Treo-650/2008-11-13/sdcard-base.tar.gz
+ which is a compressed tar archive of the contents of an sd card containing
+ cocoboot. Use mkdosfs to create a fat16 filesystem on the first primary
+ partition of the card, mount the partition, and extract the tar file to it.
+ You will probably need to edit the cocoboot.conf file to customize the
+ parameters passed to the kernel.
+
+
+
+Linux kernel:
+
+ The kernel on the Treo 680 is still a little rough around the edges, and the
+ official kernel frequently breaks on the Treo :( A development kernel
+ specifically for the Treo 680 can be found on github:
+ http://github.com/mike-dunn/linux-treo680
+ The master branch of this tree has been tested on the Treo, and I recommend
+ using this kernel for programming u-boot. As of this writing, there may be a
+ bug in the docg4 nand flash driver that sometimes causes block erasures to
+ fail. This has been fixed in the above tree.
+
+ If you choose to use the official kernel, it must contain the docg4 driver that
+ includes the reliable_mode module parameter. This was a later enhancement to
+ the driver, and was merged to the kernel as of v3.8. Do not try to use an
+ earlier kernel that contains the docg4 driver without support for writing in
+ reliable mode. If you try to program u-boot to flash with the docg4 driver
+ loaded without the reliable_mode parameter enabled, you *will* brick your
+ phone!
+
+ For the purpose of programming u-boot to flash, the following options must be
+ enabled in the Treo kernel's .config:
+
+ CONFIG_MTD=y
+ CONFIG_MTD_CMDLINE_PARTS=y
+ CONFIG_MTD_CHAR=y
+ CONFIG_MTD_NAND_DOCG4=m
+
+ Note that the docg4 nand driver is configured as a module, because we will
+ want to load and unload it with reliable_mode enabled or disabled as needed.
+
+ You will also need to specify mtd partitions on the kernel command line. In
+ the instructions that follow, we will assume that the flash blocks to which
+ u-boot will be programmed are defined by the second partition on the device.
+ The u-boot config file (include/configs/palmtreo680.h) places the u-boot image
+ at the start of block 6 (offset 0x180000), which is the first writable
+ (non-protected) block on the flash (this is also where the PalmOS SPL starts).
+ The u-boot image occupies four blocks, so to create the u-boot partition, pass
+ this command line to the kernel:
+ mtdparts=Msys_Diskonchip_G4:1536k(protected_part)ro,1024k(bootloader_part),-(filesys_part)
+ This will create three partitions:
+ protected_part: the first six blocks, which are read-only
+ bootloader_part: the next four blocks, for the u-boot image
+ filesys_part: the remainder of the device
+ The mtdchar kernel device driver will use device nodes /dev/mtd0, /dev/mtd1,
+ and /dev/mtd2 for these partitions, respectively. Ensure that your root file
+ system at least has /dev/mtd1 if you are not running udev or mdev.
+
+
+Userspace Utilities:
+
+ In addition to everything necessary to provide a useful userspace environment
+ (busybox is indispensable, of course), you will need the mtd-utils package on
+ your root filesystem. I use version 1.5.0 of mtd-utils, and I suggest you use
+ this version as well, or at leat a version very close to this one, as
+ mtd-utils has tended to be fluid.
+
+ Note that busybox includes a version of mtd-utils. These are deficient and
+ should not be used. When you run one of these utilities (nanddump, etc),
+ ensure you are invoking the separate executable from mtd-utils, and not the
+ one built into busybox. I recommend that you configure busybox with its
+ mtd-utils disabled to avoid any possibility of confusion.
+
+ You will also need to cross-compile the userspace Linux utility in
+ board/palmtreo680/flash_u-boot.c, which we will run on the Treo to perform the
+ actual write of the u-boot image to flash. This utility links against libmtd
+ from the mtd-utils package.
+
+
+
+Desktop PC-side Software Prerequisites
+======================================
+
+Terminal emulator application:
+ minicom, kermit, etc.
+
+
+Linux kernel:
+ Compiled with CONFIG_USB_SERIAL enabled. Build this as a module.
+
+
+
+Recommended (Not directly related to u-boot)
+============================================
+
+Working directly on the Treo's tiny screen and keypad is difficult and
+error-prone. I recommend that you log into the Linux kernel running on your
+Treo from your desktop PC using ethernet over usb. The desktop's kernel must be
+configured with CONFIG_USB_USBNET, CONFIG_USB_NET_CDCETHER, and
+CONFIG_USB_NET_CDC_SUBSET. The Treo's kernel will need CONFIG_USB_ETH, and its
+init script will need to start an ssh daemon like dropbear. Note that the usb0
+network interface will not appear on the desktop PC until the Treo kernel's usb
+ethernet gadget driver has initialized. You must wait for this to occur (watch
+the PC's kernel log) before you can assign usb0 an ip address and log in to the
+Treo. If you also build the Treo's kernel with CONFIG_IP_PNP enabled, you can
+pass its ip address on the kernel command line, and obviate the need to
+initialize the network interface in your init script.
+
+Having the Palm usb cable connected to the host has the added benefit of keeping
+power supplied to your Treo, reducing the drain on the battery. If something
+goes wrong while you're programming u-boot to the flash, you will have lots of
+time to correct it before the battery dies.
+
+I have encountered a situation where the kernel is sometimes unable to mount a
+root filesystem on the mmc card due to the mmc controller not coming up in time,
+(and CONFIG_MMC_UNSAFE_RESUME doesn't seem to help) so I recommend that you
+build a minimal root filesystem into the kernel using the kernel's initramfs
+feature (CONFIG_BLK_DEV_INITRD). If you want your root filesystem on the mmc
+card, your init script can mount and switch_root to the mmc card after a short
+sleep. But keep in mind that in this case you won't be able to use an mmc card
+to transfer files between your desktop and the Treo. Another option for
+transfering files is to mount an nfs filesystem exported by the desktop PC. For
+greatest convenience, you can export the root filesystem itself from your
+desktop PC and switch_root to it in your init script. This will work if your
+init script contains a loop that waits for you to initialize the usb0 network
+interface on the desktop PC; e.g., loop while a ping to the desktop PC returns
+an error. After the loop exits, do the nfs mount and call switch_root. (You
+can not use the kernel nfsroot feature because the network will not be up when
+the kernel expects it to be; i.e., not until you configure the usb0 interface on
+the desktop.) Use the nfs 'nolock' option when mounting to avoid the need to
+run a portmapper like rpcbind.
+
+
+
+Preliminaries
+=============
+
+Once Linux is running on your Treo, you may want to perform a few sanity checks
+before programming u-boot. If you are impatient and reckless, you may skip this
+section, but see disclaimer at the top of this file!
+
+Load the docg4 driver (you did build this as a module, right?):
+
+ $ modprobe docg4 ignore_badblocks=1 reliable_mode=1
+
+We tell the driver to use the docg4's "reliable mode" when writing because this
+is the format required by the initial program loader (IPL), which runs from
+power-up and loads the first portion of u-boot. We must ignore bad blocks
+because linux mtd uses out-of-band (oob) bytes to mark bad blocks, which will
+cause the blocks written by PalmOS to be misidentified as "bad" by libmtd.
+
+Check the kernel log to ensure that all's well:
+
+ $ dmesg | tail
+ <... snip ...>
+ docg4 docg4: NAND device: 128MiB Diskonchip G4 detected
+ 3 cmdlinepart partitions found on MTD device Msys_Diskonchip_G4
+ Creating 3 MTD partitions on "Msys_Diskonchip_G4":
+ 0x000000000000-0x000000180000 : "protected_part"
+ 0x000000180000-0x000000280000 : "bootloader_part"
+ 0x000000280000-0x000008000000 : "filesys_part"
+
+Ensure that the partition boundaries are as shown. (If no partitions are shown,
+did you remember to pass them to the kernel on the command line?) We will write
+u-boot to bootloader_part, which starts at offset 0x180000 (block 6) and spans 4
+256k blocks. This partition is accessed through the device node /dev/mtd1.
+
+The docg4 contains a read-only table that identifies blocks that were marked as
+bad at the factory. This table is in the page at offset 0x2000, which is within
+the partition protected_part (/dev/mtd0). There is a slight chance that one or
+more of the four blocks that we will use for u-boot is listed in the table, so
+use nanddump to inspect the table to see if this is the case:
+
+ $ nanddump -p -l 512 -s 0x2000 -o /dev/mtd0
+ ECC failed: 0
+ ECC corrected: 0
+ Number of bad blocks: 0
+ Number of bbt blocks: 0
+ Block size 262144, page size 512, OOB size 16
+ Dumping data starting at 0x00002000 and ending at 0x00002200...
+ 0x00002000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
+ <... snip ...>
+
+The format of the table is simple: one bit per block, with block numbers
+increasing from left to right, starting with block 0 as the most significant bit
+of the first byte. A bit will be clear if the corresponding block is bad. We
+want to use blocks 6 throgh 9, so both of the two least significant bits of the
+first byte must be set, as must the two most significant bits of the second
+byte. If this is not true in your case (you are very unlucky), you should use
+the first contiguous set of four good blocks after block 6, and adjust the
+partition boundaries accordingly. You will also have to change the value of
+CONFIG_SYS_NAND_U_BOOT_OFFS in include/configs/palmtreo680.h and recompile
+u-boot. Because the two blocks loaded by the IPL do not have to be contiguous,
+but our SPL expects them to be, you will need to erase any good blocks that are
+at an offset prior to CONFIG_SYS_NAND_U_BOOT_OFFS, so that the IPL does not find
+the magic number in oob and load it (details below). Once you have done all
+this, the instructions in this file still apply, except that the instructions
+below for restoring the original PalmOS block contents may not work.
+
+Next, use nanddump to verify that the PalmOS SPL is where we expect it to be.
+The SPL can be identified by a magic number in the oob bytes of the first page
+of each of the two blocks containing the SPL image. Pages are 512 bytes in
+size, so to dump the first page, plus the oob:
+
+ $ nanddump -p -l 512 -s 0 -o /dev/mtd1
+ ECC failed: 0
+ ECC corrected: 0
+ Number of bad blocks: 0
+ Number of bbt blocks: 0
+ Block size 262144, page size 512, OOB size 16
+ Dumping data starting at 0x00000000 and ending at 0x00000200...
+ 0x00000000: 0a 00 00 ea 00 00 00 00 00 00 00 00 00 00 00 00
+ <... snip ...>
+ 0x000001f0: 13 4c 21 60 13 4d 2a 69 13 4b 29 69 89 1a 99 42
+ OOB Data: 42 49 50 4f 30 30 30 10 3a e2 00 92 be a0 11 ff
+
+Verify that the first seven bytes of oob data match those in the above line.
+(This is ASCII "BIPO000".)
+
+Do the same for the next block:
+ $ nanddump -p -l 512 -s 0x40000 -o /dev/mtd1
+
+The first seven oob bytes in last line should read:
+
+ OOB Data: 42 49 50 4f 30 30 31 81 db 8e 8f 46 07 9b 59 ff
+
+(This is ASCII "BIPO001".)
+
+For additional assurance, verify that the next block does *not* contain SPL
+data.
+
+ $ nanddump -p -l 512 -s 0x80000 -o /dev/mtd1
+
+It doesn't matter what the oob contains, as long as the first four bytes are
+*not* ASCII "BIPO". PalmOS should only be using two blocks for the SPL
+(although we will need four for u-boot).
+
+If you want, you can back up the contents of bootloader_part to a file. You may
+be able to restore it later, if desired (see "Restoring PalmOS" below).
+
+ $ nanddump -l 0x100000 -s 0 -o -f bootloader_part.orig /dev/mtd1
+
+nanddump will spew voluminous warnings about uncorrectable ecc errors. This is
+a consequence of reading pages that were written in reliable mode, and is
+expected (these should all occur on pages in odd-numbered 2k regions; i.e.,
+0x800, 0xa00, 0xc00, 0xe00, 0x1800, 0x1a00, ...). The size of the file
+bootloader_part.orig should be 1081344, which is 2048 pages, each of size 512
+plus 16 oob bytes. If you are using initramfs for the root filesystem, don't
+forget to copy the file to permanent storage, such as an mmc card.
+
+If all of the above went well, you can now program u-boot.
+
+
+
+Programming u-boot
+==================
+
+Our u-boot includes a small SPL (secondary program loader) that must be
+prepended to u-boot proper. From the base u-boot source directory on your
+desktop PC:
+
+ $ cat spl/u-boot-spl.bin u-boot.bin > u-boot-concat.bin
+
+cd to the board/palmtreo680/ directory, and cross-compile flash_u-boot.c for the
+Treo:
+
+ $(CC) -o flash_u-boot $(CFLAGS) $(INCLUDEPATH) $(LIBPATH) flash_u-boot.c -lmtd
+
+Substitute variable values from your cross-compilation environment as
+appropriate. Note that it links to libmtd from mtd-utils, and this must be
+included in $(LIBPATH) and $(INCLUDEPATH).
+
+Transfer u-boot-concat.bin and the compiled flash_u-boot utility to the Treo's
+root filesystem. On the Treo, cd to the directory where these files were
+placed.
+
+Load the docg4 driver if you have not already done so.
+
+ $ modprobe docg4 ignore_badblocks=1 reliable_mode=1
+
+Erase the blocks to which we will write u-boot.
+
+ $ flash_erase /dev/mtd1 0x00 4
+
+We can now program the flash.
+
+ ./flash_u-boot u-boot-concat.bin /dev/mtd1
+
+You can use nanddump (see above) to verify that the data was written. This
+time, "BIPO" should be seen in the first four oob bytes of the first page of all
+four blocks in /dev/mtd1; i.e., at offsets 0x00000, 0x40000, 0x80000, 0xc0000.
+
+Shutdown linux, remove and re-insert the battery, hold your breath...
+
+
+
+Enjoying u-boot
+===============
+
+After you insert the battery, the u-boot splash screen should appear on the lcd
+after a few seconds. With the usb cable connecting the Treo to your PC, in the
+kernel log of your PC you should see
+
+ <6>usb 3-1: New USB device found, idVendor=0525, idProduct=a4a6
+ <6>usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
+ <6>usb 3-1: Product: U-Boot 2013.01-00167-gd62ef56-dirty
+ <6>usb 3-1: Manufacturer: Das U-Boot
+
+Load the usbserial module on your desktop PC:
+
+ $ modprobe usbserial vendor=0x0525 product=0xa4a6
+
+and run your favorite terminal emulation utility (minicom, kermit, etc) with the
+serial device set to /dev/ttyUSB0 (assuming this is your only usb serial
+device). You should be at the u-boot console (type 'help').
+
+There is not much that is unique about using u-boot on the palm treo 680.
+Kernels can be loaded from mmc, flash, and from the desktop PC via kermit. You
+can expand the size of the second partition on the flash to contain a kernel, or
+else put the kernel(s) in their own partition.
+
+Nand commands work as expected, with the excepton that blocks not written by the
+linux mtd subsystem may be misidentified by the u-boot docg4 driver as "bad" if
+they contain data in the oob bytes. This will be the case for the blocks
+containing the u-boot image, for example. To work around this, use 'nand scrub'
+to erase these blocks, and 'nand read.raw' to read them. (It would be useful if
+u-boot's nand commands provided a way to explicitly ignore "bad" blocks, because
+read.raw does not perform ecc.)
+
+Currently u-boot itself can only be programmed to flash from Linux; there is no
+support for reliable mode in u-boot's docg4 flash driver. This should be
+corrected soon.
+
+
+
+Customizing
+===========
+
+If you change u-boot's configuration significantly (adding or removing
+features), you may have to adjust the value of CONFIG_SYS_NAND_U_BOOT_SIZE.
+This is the size of the concatenated spl + u-boot image, and tells the SPL how
+many flash blocks it needs to load. It will be rounded up to the next 64k
+boundary (the spl flash block capacity), so it does not have to be exact, but
+you must ensure that it is not less than the actual image size. If it is larger
+than the image, blocks may be needlessly loaded, but if too small, u-boot may
+only be partially loaded, resulting in a boot failure (bricked phone), so better
+to be too large. The flash_u-boot utility will work with any size image and
+write the required number of blocks, provided that the partition is large
+enough.
+
+As the first writable block on the device, block 6 seems to make the most sense
+as the flash offset for writing u-boot (and this is where PalmOS places its
+SPL). But you can place it elsewhere if you like. If you do, you need to
+adjust CONFIG_SYS_NAND_U_BOOT_OFFS accordingly, and you must ensure that blocks
+preceeding the ones containing u-boot do *not* have the magic number in oob (the
+IPL looks for this). In other words, make sure that any blocks that previously
+contained the u-boot image or PalmOS SPL are erased (and optionally written with
+something else) so that the IPL does not load it. Also make sure that the new
+u-boot starting offset is at the start of a flash partition (check the kernel
+log after loading the docg4 driver), and pass the corresponding mtd device file
+to the flash_u-boot utility.
+
+The u-boot built-in default environment is used because a writable environment
+in flash did not seem worth the cost of a 256k flash block. But adding this
+should be straightforward.
+
+
+
+Details on the SPL
+==================
+
+The docg4 features a 2k region at the start of its address space that interfaces
+to the system bus like a NOR flash. This allows the docg4 to function as a boot
+ROM. The Treo 680 uses this feature. The contents of this 2k region are
+protected and can not be reprogrammed (at least I don't know how to do it).
+Fortunately, the code it contains does what we need to do, at least partially.
+After some essential hardware initialization (like the SDRAM controller), it
+runs an IPL (initial program loader) that copies 128K (no more, no less) to a
+fixed address in SDRAM and then jumps to it. 128K is too small for u-boot, so
+we use it to load a u-boot SPL. But since our SPL only occupies a little over
+1k, we can economize on flash usage by having the IPL load a portion of u-boot
+proper as well. We let the IPL load two blocks of a concatenated spl + u-boot
+image, and because the SPL is placed before u-boot proper, the IPL jumps to the
+SPL, which copies to its correct SDRAM address the portion of u-boot that the
+IPL has already loaded, and then loads the remaining u-boot blocks.
+
+
+
+The docg4's "reliable mode"
+===========================
+
+This is a special mode of operation of the hardware whereby consecutive pairs of
+2k regions are used in parallel (in some fashion) to store 2k of data. In other
+words, the normal capacity is halved, but the data integrity is improved. In
+this mode, the data is read or written from pages in even-numbered 2k regions
+(regions starting at 0x000, 0x1000, 0x2000, ...), and the odd-numbered 2k
+regions (regions starting at 0x800, 0x1800, 0x2800, ...) are transparently used
+in parallel. In reliable mode, the odd-numbered 2k regions are not meant to be
+read or written directly.
+
+Reliable mode is used by the IPL because there is not enough space in its 2k
+footprint to implement the BCH ecc algorithm. Data that is read while reliable
+mode is enabled must have been written in reliable mode, or the read fails.
+However, data written in reliable mode can also be read in normal mode (just not
+as reliably), but only from the even-numbered 2k regions; the odd-numbered 2k
+regions appear to contain junk, and will generate ecc errors. When the IPL and
+SPL read from flash, the odd-numbered 2k regions are explicitly skipped. The
+same is true for the flash_u-boot utility when it writes the u-boot image in
+reliable mode.
+
+The docg4 Linux driver supports writing in reliable mode (it is enabled by the
+module parameter), but not reading. However, the u-boot docg4_spl driver does
+read in reliable mode, in the same fashion as the IPL.
+
+
+
+Details on the IPL and its data format
+======================================
+
+Starting from block 5 and counting upward, the IPL will search for and load the
+first two blocks it finds that contain a magic number in the oob of the first
+page of the block. The contents are loaded to SDRAM starting at address
+0xa1700000. After two blocks have been loaded, it jumps to 0xa1700000. The
+number of blocks loaded and the load address in SDRAM are hard-coded; only the
+flash offset of the blocks can vary at run-time (based on the presence of the
+magic number).
+
+In addition to using the docg4's reliable mode, the IPL expects each 512 byte
+page to be written redundantly in the subsequent page. The hardware is capable
+of detecting bit errors (but not correcting them), and if a bit error is
+detected when a page is read, the page contents are discarded and the subsequent
+page is read.
+
+Reliable mode reduces the capacity of a block by half, and the redundant pages
+reduce it by half again. As a result, the normal 256k capacity of a block is
+reduced to 64k for the purposes of the IPL/SPL.
+
+For the sake of simplicity and uniformity, the SPL mimics the operation of the
+IPL, and expects the image to be stored in the same format.
+
+
+
+Restoring PalmOS
+================
+
+If you backed up the contents of bootloader_part flash partition earlier, you
+should be able to restore it with the shell script shown below. The first two
+blocks of data contain the PalmOS SPL and were written in reliable mode, whereas
+the next two blocks were written in normal mode, so the script has to load and
+unload the docg4 driver. Make sure that the mtd-utils nandwrite and flash_erase
+are in your path (and are not those from busybox). Also double-check that the
+backup image file bootloader_part.orig is exactly 1081344 bytes in length. If
+not, it was not backed up correctly. Run the script as:
+
+ ./restore_bootpart bootloader_part.orig /dev/mtd1
+
+The script will take a minute or so to run. When it finishes, you may want to
+verify with nanddump that the data looks correct before you cycle power, because
+if the backup or restore failed, your phone will be bricked. Note that as a
+consequence of reliable mode, the odd-numbered 2k regions in the first two
+blocks will not exactly match the contents of the backup file (so unfortunately
+we can't simply dump the flash contents to a file and do a binary diff with the
+original back-up image to verify that it was restored correctly). Also,
+nanddump will report uncorrectable ecc errors when it reads those regions.
+
+#!/bin/sh
+
+if [ $# -ne 2 ]; then
+ echo "usage: $0: <image file> "
+ exit 1
+fi
+
+# reliable mode used for the first two blocks
+modprobe -r docg4
+modprobe docg4 ignore_badblocks=1 reliable_mode=1 || exit 1
+
+# erase all four blocks
+flash_erase $2 0 4
+
+# Program the first two blocks in reliable mode.
+# 2k (4 pages) is written at a time, skipping alternate 2k regions
+# Note that "2k" is 2112 bytes, including 64 oob bytes
+file_ofs=0
+flash_ofs=0
+page=0
+while [ $page -ne 1024 ]; do
+ dd if=$1 bs=2112 skip=$file_ofs count=1 | nandwrite -o -n -s $flash_ofs $2 - || exit 1
+ file_ofs=$((file_ofs+2))
+ flash_ofs=$((flash_ofs+0x1000))
+ page=$((page+8))
+done;
+
+# normal mode used for the next two blocks
+modprobe -r docg4
+modprobe docg4 ignore_badblocks=1 || exit 1
+dd if=$1 bs=1 skip=$file_ofs count=540672 | nandwrite -o -n -s 0x80000 $2 - || exit 1
+modprobe -r docg4
+
+
+TODO
+====
+
+ - Keypad support.
+ - Interactive boot menu using keypad and lcd.
+ - Add reliable mode support to the u-boot docg4 driver.
+ - U-boot command that will write a new image to the bootloader partition in
+ flash.
+ - Linux FTD support.
+
diff --git a/include/configs/palmtreo680.h b/include/configs/palmtreo680.h
new file mode 100644
index 0000000..9afc4ca
--- /dev/null
+++ b/include/configs/palmtreo680.h
@@ -0,0 +1,307 @@
+/*
+ * Palm Treo 680 configuration file
+ *
+ * Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_CPU_PXA27X 1
+#define CONFIG_PALMTREO680 1
+
+
+#define CONFIG_SYS_MALLOC_LEN (4096*1024)
+
+#define CONFIG_LZMA
+
+/*
+ * Serial Console Configuration
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART 1
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_CONS_INDEX 3
+
+/* we have nand (although technically nand *is* flash...) */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_LCD
+/* #define CONFIG_KEYBOARD */ /* TODO */
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
+#undef CONFIG_CMD_XIMG
+
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NAND
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+#define CONFIG_MACH_TYPE 1230
+
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_PXA_MMC_GENERIC
+
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_PXA_LCD
+#define CONFIG_ACX544AKN
+#define CONFIG_LCD_LOGO
+#define CONFIG_SYS_LCD_PXA_NO_L_BIAS /* don't configure GPIO77 as L_BIAS */
+#define LCD_BPP LCD_COLOR16
+#define CONFIG_FB_ADDR 0x5c000000 /* internal SRAM */
+#define CONFIG_CMD_BMP
+#define CONFIG_SPLASH_SCREEN /* requires "splashimage" env var */
+#define CONFIG_SPLASH_SCREEN_ALIGN /* requires "splashpos" env var */
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
+
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port speed */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_LONGHELP
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ "
+#else
+#define CONFIG_SYS_PROMPT "=> "
+#endif
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+
+/*
+ * Clock Configuration
+ */
+#undef CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_CPUSPEED 0x210 /* 416MHz ; N=2,L=16 */
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000
+#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_DRAM_BASE
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GAFR0_L_VAL 0x0E000000
+#define CONFIG_SYS_GAFR0_U_VAL 0xA500001A
+#define CONFIG_SYS_GAFR1_L_VAL 0x60000002
+#define CONFIG_SYS_GAFR1_U_VAL 0xAAA07959
+#define CONFIG_SYS_GAFR2_L_VAL 0x02AAAAAA
+#define CONFIG_SYS_GAFR2_U_VAL 0x41440F08
+#define CONFIG_SYS_GAFR3_L_VAL 0x56AA95FF
+#define CONFIG_SYS_GAFR3_U_VAL 0x00001401
+#define CONFIG_SYS_GPCR0_VAL 0x1FF80400
+#define CONFIG_SYS_GPCR1_VAL 0x03003FC1
+#define CONFIG_SYS_GPCR2_VAL 0x01C1E000
+#define CONFIG_SYS_GPCR3_VAL 0x01C1E000
+#define CONFIG_SYS_GPDR0_VAL 0xCFF90400
+#define CONFIG_SYS_GPDR1_VAL 0xFB22BFC1
+#define CONFIG_SYS_GPDR2_VAL 0x93CDFFDF
+#define CONFIG_SYS_GPDR3_VAL 0x0069FF81
+#define CONFIG_SYS_GPSR0_VAL 0x02000018
+#define CONFIG_SYS_GPSR1_VAL 0x00000000
+#define CONFIG_SYS_GPSR2_VAL 0x000C0000
+#define CONFIG_SYS_GPSR3_VAL 0x00080000
+
+#define CONFIG_SYS_PSSR_VAL 0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN 0x01ffffff
+#define CONFIG_SYS_CCCR 0x02000210
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x7ff844c8
+#define CONFIG_SYS_MSC1_VAL 0x7ff86ab4
+#define CONFIG_SYS_MSC2_VAL 0x7ff87ff8
+#define CONFIG_SYS_MDCNFG_VAL 0x0B880acd
+#define CONFIG_SYS_MDREFR_VAL 0x201fa031
+#define CONFIG_SYS_MDMRS_VAL 0x00320032
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000003
+#define CONFIG_SYS_MCMEM0_VAL 0x0001c391
+#define CONFIG_SYS_MCMEM1_VAL 0x0001c391
+#define CONFIG_SYS_MCATT0_VAL 0x0001c391
+#define CONFIG_SYS_MCATT1_VAL 0x0001c391
+#define CONFIG_SYS_MCIO0_VAL 0x00014611
+#define CONFIG_SYS_MCIO1_VAL 0x0001c391
+
+/*
+ * USB
+ */
+#define CONFIG_USB_DEVICE
+#define CONFIG_USB_TTY
+#define CONFIG_USB_DEV_PULLUP_GPIO 114
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_TEXT_BASE 0xa1700000 /* IPL loads SPL here */
+#define CONFIG_SPL_STACK 0x5c040000 /* top of internal SRAM */
+#define CONFIG_SPL_LDSCRIPT board/palmtreo680/palmtreo680_spl.lds
+#define CONFIG_SPL_NAND_SUPPORT /* build libnand for spl */
+#define CONFIG_SPL_NAND_DOCG4 /* use lean docg4 nand spl driver */
+
+/*
+ * NAND
+ */
+#define CONFIG_NAND_DOCG4
+#define CONFIG_SYS_NAND_SELF_INIT
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* only one device */
+#define CONFIG_SYS_NAND_BASE 0x00000000 /* mapped to reset vector */
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x200
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
+#define CONFIG_BITREVERSE /* needed by docg4 driver */
+#define CONFIG_BCH /* needed by docg4 driver */
+
+/*
+ * IMPORTANT NOTE: this is the size of the concatenated spl + u-boot image. It
+ * will be rounded up to the next 64k boundary (the spl flash block size), so it
+ * does not have to be exact, but you must ensure that it is not less than the
+ * actual image size, or it may fail to boot (bricked phone)!
+ * (Tip: reduces to three blocks with lcd and mmc support removed from u-boot.)
+*/
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x40000 /* four 64k flash blocks */
+
+/*
+ * This is the byte offset into the flash at which the concatenated spl + u-boot
+ * image is placed. It must be at the start of a block (256k boundary). Blocks
+ * 0 - 5 are write-protected, so we start at block 6.
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x180000 /* block 6 */
+
+/* DRAM address to which u-boot proper is loaded (before it relocates itself) */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0xa0000000
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+
+/* passed to linker by Makefile as arg to -Ttext option */
+#define CONFIG_SYS_TEXT_BASE 0xa0000000
+
+#define CONFIG_SYS_INIT_SP_ADDR 0x5c040000 /* end of internal SRAM */
+
+/*
+ * environment
+ */
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_BUILD_ENVCRC
+#define CONFIG_ENV_SIZE 0x200
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "stdin=usbtty\0" \
+ "stdout=usbtty\0" \
+ "stderr=usbtty"
+#define CONFIG_BOOTARGS \
+"mtdparts=Msys_Diskonchip_G4:1536k(protected_part)ro,1024k(bootloader_part),-(filesys_part) \
+ip=192.168.11.102:::255.255.255.0:treo:usb0"
+#define CONFIG_BOOTDELAY 3
+
+#if 0 /* example: try 2nd mmc partition, then nand */
+#define CONFIG_BOOTCOMMAND \
+ "mmc rescan; " \
+ "if mmcinfo && ext2load mmc 0:2 0xa1000000 uImage; then " \
+ "bootm 0xa1000000; " \
+ "elif nand read 0xa1000000 0x280000 0x240000; then " \
+ "bootm 0xa1000000; " \
+ "fi; "
+#endif
+
+/* u-boot lives at end of SDRAM, so use start of SDRAM for stand alone apps */
+#define CONFIG_STANDALONE_LOAD_ADDR 0xa0000000
+
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_ICACHE_OFF
+
+#endif /* __CONFIG_H */
--
1.7.8.6