[U-Boot] [PATCH v2 1/3] ARM: Tegra: FDT: Add USB EHCI function for T30/T114

[Marek Vasut <marex@denx.de>]

Dear Thierry Reding,

> On Sat, Jun 15, 2013 at 11:28:25PM +0200, Marek Vasut wrote:
> > Dear Thierry Reding,
> > 
> > > On Fri, Jun 14, 2013 at 06:41:40PM +0800, Jim Lin wrote:
> > > [...]
> > > 
> > > > diff --git a/board/nvidia/dts/tegra30-beaver.dts
> > > > b/board/nvidia/dts/tegra30-beaver.dts
> > > 
> > > [...]
> > > 
> > > > @@ -68,4 +69,9 @@
> > > > 
> > > >  		status = "okay";
> > > >  		bus-width = <8>;
> > > >  	
> > > >  	};
> > > > 
> > > > +
> > > > +	usb at 7d008000 {
> > > > +		nvidia,vbus-gpio = <&gpio 61 3>; /* PH5, 
USB13_VBUS_PULLUP */
> > > 
> > > This doesn't work for me on Beaver. I need to turn the above line into
> > > 
> > > this:
> > > 	nvidia,vbus-gpio = <&gpio 236 0>; /* PDD4 */
> > > 
> > > PDD4 is the correct GPIO according to the schematics and the pin is
> > > high-active. Also as far as I can tell, 3 is not a meaningful value for
> > > the U-Boot GPIO bindings. Only the value 1 (low-active) is used.
> > > 
> > > With that change applied on top of your patches I can see that a USB
> > > flash drive connected to USB3 is indeed powered. However I noticed
> > > 
> > > something strange. When I try to use USB, I get this:
> > > 	Tegra30 (Beaver) # usb start
> > > 	(Re)start USB...
> > > 	USB0:   set_host_mode: GPIO 236 high
> > > 	USB EHCI 1.00
> > > 	scanning bus 0 for devices... 1 USB Device(s) found
> > > 	
> > > 	       scanning usb for storage devices... 0 Storage Device(s) found
> > > 	       scanning usb for ethernet devices... 0 Ethernet Device(s) found
> > > 
> > > So no storage device is detected, even though a USB flash drive is
> > > connected and powered properly. If I repeat the same command, however,
> > > 
> > > the storage device is detected:
> > > 	Tegra30 (Beaver) # usb reset
> > > 	(Re)start USB...
> > > 	USB0:   set_host_mode: GPIO 236 high
> > > 	USB EHCI 1.00
> > > 	scanning bus 0 for devices... 2 USB Device(s) found
> > > 	
> > > 	       scanning usb for storage devices... 1 Storage Device(s) found
> > > 	       scanning usb for ethernet devices... 0 Ethernet Device(s) found
> > > 
> > > Any idea what might be going on here?
> > 
> > Try waiting a little after setting the GPIO maybe? The drive might need
> > some time to settle.
> 
> I can make it work on the first invocation of "usb start" by adding a
> rather long mdelay() at the very end of ehci_hcd_init() in the Tegra
> EHCI driver. The magic value seems to be 853 ms. 852 ms wasn't enough
> in any of the test runs. 853 ms always worked.
> 
> However 850+ ms seems like a very long time for the device to settle,
> and keeping it in the driver probably isn't a good idea. Furthermore I
> cannot reproduce the same issue with a newer flash drive, which works
> fine with no additional delays.

Try reverting 020bbcb "usb: hub: Power-cycle on root-hub ports" ... there's a 
thread in the ML that it caused issues.

Best regards,
Marek Vasut